B/ Aluminum (Tm%3660 OC) and Silicon (Tm-1410oC) were fully dissolved in each other in the liquidstate. The ultimate solubility of silicon inaluminum is 2 % at 577 OC which decreasing withdecreasing temperature to zero% at roomtemperature while the aluminum never dissolvedin silicon in solid state. Aluminum and siliconform eutectic at 577 OC and 12.2 % of Si.construct phase diagram for aluminum and siliconalloying system, label all phases andtemperatures, and show by drawing for 30 wt%silicon alloy which is slowly cooled from 10000cthe temperature of the first solid phase is formed.

Answered: B/ Aluminum (TM3D660 OC) and Silicon…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Copper (Cu) and silver (Ag) alloys form a binary alloy system that dissolves each othercompletely in the liquid state but only partially soluble in each other in the solid state.- The melting point of Cu is 1080 C and the melting point of Ag is 960 C.- At a temperature of 790 C, a eutectic reaction occurs in the 72% Ag alloy. At this temperature, Cucapable of dissolving 10% Ag and its eutectic microstructure is known to have a ratio of /β = 7/19 (findthe point of solubility of Cu in Ag at the eutectic temperature).- At room temperature (25 C), Cu metal can dissolve 5% Ag while Ag metal candissolve 2% Cu.a. Draw a phase diagram of the alloy system complete with the names of points, lines and phase regions.b. The 80%Ag alloy is cooled in equilibrium.i. Draw the cooling curve from liquid to solid state, complete withtemperature, the phases at each stage and the reactions that occur.ii. At the eutectic temperature (4a before and 4b after the eutectic reaction), determine the…
What is the solubility of naphthalene at 50 C in an ideal solution? The melting point of naphthalene is 90 C and the molar heat of fusion is 3500 cal/mole. the gas constant = 1.987 cal mol'degree %3D Select one: O a. 0.55 Ob.93.3 Oc.0.27 Od.6.7
1. An FCC iron-carbon alloy initially containing 0.20 wt% C is carburized at an elevated temperature and in an atmosphere that gives a surface carbon concentration constant at 1.0 wt%. If after 49.5 h, the concentration of carbon is 0.35 wt% at a position 4.0 mm below the surface, determine the temperature at which the treatment was carried out. 2. Consider a metal single-crystal oriented such that the normal to the slip plane and the slip direction are at angles of 60° and 35°, respectively, with the tensile axis. If the critical resolved shear stress is 20.7 MPa, will an applied stress of 45 MPa cause the single crystal to yield? If not, what stress will be necessary?
Decarburization of a steel occurs when carbon diffuses from the steel to the surface and enters the atmosphere. How long will it take for a 0.6 % C steel surface to decarburize below 0.1 % C for a depth of 2 mm if the FCC steel is held at 1250 °C in an atmosphere containing zero carbon? I need this question's answer. It's important for me.
Diffusion 4) Determine the carburizing time necessary to achieve a carbon concentration of 0.4wt% at a position 0.5 mm into an iron-carbon alloy that initially contains 0.2wt% C. The surface concentration is to be maintained at 0.9wt% and the treatment is to be conducted at 927°C. D @927 °C = 1.28 x 10" m'/s Critical Resolved Shear Stress 5) A single crystal of a metal has a critical shear stress of 2.2 MPa. If a stress of 5 MPa is applied along the [100] direction of a unit cell then what will be the resolved shear stress for the (111)[101] slip system? Will the crystal exhibit slip? Schmid's Law Sie Sie plane crection A•B/(A||B)
6. (20%) Pure zinc is to be diffused into the copper by dipping copper into molten zinc at 450°C. Calculate how long would take to obtain 10wt% zinc at a depth of 0.5 mm beneath the copper surface. Is this commercially feasible? What practical problems might arise if we raise the temperature to 1000°C ? Use Table below for error function values as needed. At 450°C, the diffusion coefficient D = 6.3 10-17 m²/s.
For the phase diagram of Pb-Sn system, the maximum solubility of Sn in Lead is 99 % 97.8 % 61.9% 18.3%
For a steel alloy it has been determined that a carburizing heat treatment of 16 h duration at 731°C will raise the carbon concentration to 0.40 wt% at a point 3.9 mm from the surface. Estimate the time necessary to achieve the same concentration at a 7.9 mm position for an identical steel and at a carburizing temperature of 1060°C. Assume that Do is 1.9 x 105 m²/s and Quis 108 kJ/mol, 3.89 -land Madin h
V, Vapor - 90 bpB 90 80 + 80 70 - i+ 70 60 tv, Liquid 60 3D 50 %3D 50 3D 100% A 0% 80 20 60 40 40 60 20 0% 80 100% B d. If we purify all the way to L5, what will be its boiling point and composition then? Temperature
An FCC iron–carbon alloy initially containing 0.25wt% C is carburized at an elevated temperature and in an atmosphere wherein thesurface carbon concentration is maintained at 1.0 wt%. If after 55.0 h the concentrationof carbon is 0.35 wt% at a position 5.0 mm below the surface, determine thetemperature at which the treatment was carried out.
The lead and tin are partially dissolved in each other in solid state although they completely dissolved in liquid state. They form eutectic from solid solutions alfa (a) and beta (B) at alloying composition 62% tin and 38% lead, the eutectic forming temperature is 184°C. Alfa contained 20% tin dissolved in 80% lead at 184°C while beta consist of lead dissolved in tin at 184°C. If the 100 g of eutectic contained 45.5 g of alfa at 184°C.Knowing that the melting temperatures of lead and tin are 329°C and 232°C respectively, and the solubility of tin and lead in each other's diminished to zero at room temperature. Answer the following a) Plot the phase diagram for lead-tin system label all phases and temperature. b) What is the composition of beta at eutectic temperature. c) For 40 % lead alloy calculate the phase amount and composition at 350°C, 170°C, and Tr
A mechanism for hardening steel is called carburization. To achieve this process, the piece of steel is exposed to an atmosphere rich in hydrocarbon such as methane (CH4). Consider a steel with a carbide concentration of 0.25wt%, which must be treated at 950˚C. If the carbon concentration at the surface is suddenly increased to 1.20wt%, how long does it take for a penetration of 0.5mm from the surface to reach a concentration of 0.80wt%? . The diffusion coefficient for carbon in iron at this temperature is 1.6 x 10-11 m2s-1. Assume that the piece of steel is semi-finite. Use the table below.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS