(b) Design the state diagram and state transition table for the state table in Table 1. Hence, construct a sequential logic circuit to realize the output using D flip-flops. Table 1 State Table PRESENT State Input NEXT State Output en Qn+1 y 1 1 1 1 1 1 1 (c) Design the truth table and logic circuit of a 2-input multiplexer.

(b) Design the state diagram and state transition table for the state table in Table 1. Hence, construct a sequential logic circuit to realize the output using D flip-flops. Table 1 State Table PRESENT State Input NEXT State Output en Qn+1 y 1 1 1 1 1 1 1 (c) Design the truth table and logic circuit of a 2-input multiplexer.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

We want to design a circuit to detect prime numbers.The input of the circuit is a 4-bit binary number and the output is a single bit and should show one when the number is prime and zero otherwise.B. Implement the circuit using a 4× 1 multiplexer and combinational logic gates.C. Implement the circuit using only one decoder and one OR gate. What is the size of the decoder you use?
Figure Q2(e) shows a programmable logic array (PLA) unit with two inputs, four columns, and three outputs. Show the steps to implement a one-bit comparator using this PLA. Note that the output should have equal (EQ), less than (LT), and greater (GT) status. A, 02 Figure Q2(e)
Design a 3-bit counter that counts the following sequence: 7,5, 3. 1.0.7, 5. 3, 1, 0, 7. etc. Using the sequential design technique that starts from a state diagram, draw the state table. minimize the logic. and draw the final circuit. The outputs of logic circuit are 2 = Qo Q1. I, = Qo.Qi + Qo.Qi, Io = Qo.Q2, Cont2 = Qj Q2 Cont1 = Qu Q2. Cont0 = Q2 Qo.Q1. h = Qo.Qi + Qo.Q1, Io = Qo Qz Cont2 = Q, Q2 Contl = Qo Q2 Cont0 = Q2 Qo Qı Ij = Qo.Q, + Q».Qı, Io = Qo. Q2. Cont2 = Qj Q2. Contl = Qo.Q2. Cont) = Q2 L = Qo.Qı. I¡ = Q. Qj + Qu Q Io = Qv.Qz Comt2 = Q, Q, Contl = Q Q2 Cont0 = Q2 !! fefsto How much will be per-product cost and th
The following statements describe the sequential circuits. Select all the TRUE statements. a The sequential circuits consist of a combinational circuit and storage elements. b The storage elements keep a binary bit even though the circuit power is gone. c Only the current input determines the outputs of sequential logic circuits. d The flip-flop is controlled by signal levels.
5) You want to design an arithmetic comparison combined logic circuit.a. Write your design purpose of the 4-bit comparison (big-equal-small) circuit.b. List the process steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. Realize with AND, OR, NOT gates.c. Compare the decimal numbers in the last two digits of your student number in the circuit you designed and discuss the result. last two digits of student number : 0 4 . Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, Because it is normal when solving a question to have tables and equations. I want an integrated solution, please look at the question carefully before starting the solution because I have sent a question a lot
Design a digital circuit that performs the four logic operations of exclusiveOR, exclusive-NOR, NOR, andNAND. Use two selection variables. Show the logic diagram of one typical stage.
1) by creating the state table for the state diagram given below a) draw logic diagrams by designing Sequential Circuits with JK Flip flops. b)Draw logic diagrams by designing Sequential Circuits with D-Type Flip flops.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
You want to design an arithmetic comparison combined logic circuit. (a) List the steps that you will apply in the design approach. Design a 4-bit comparison (large-equal-small) circuit. Explain each step. With AND, OR, NOT gatesmake it happen. (b)By comparing the numbers 9 and 1 in the circuit you designed, the resultdiscuss.
Using T-type flipflops, design a counter by counting the binary sequence of 7, 5, 3, 1, 0, 2, and then back to 7 by creating Karnaugh diagrams, and draw the logic circuit. If there is a situation that prevents the counter from working properly in binary situations (such as the two states constantly looping over each other), what solution should be made to overcome this situation? If there is such a case, correct the counter design according to your suggestion and show the design that will enable it to count correctly by correcting the status table. If this is not the case, do not make any changes. NOTE: The state variables are A, B, and C. Flip flop inputs are TA, TB and TC. Q(t+1) =Qn+1= Qn ⨁ TTFull Screen Reader for a T-type FF
3.) The design size of the synchronous counter sequential (sequential) logic circuit. It will count from 0 to 9 and the son of your student number will not count decimals in two digits. A. List the process steps that you will apply in the design approach. Create the State Chart and State Chart. B. Design the sequential circuit using JK Flip-Flop. Explain each step. Show that it has performed the desired action. last digit student num: 0 4 " Not : I want the solution to contain tables and equations, and the electrical circuit resulting from tables and equations, as in the picture that I attached,And if possible, I want the solution on paper if possible.
Convert the following logic gate circuit into a Boolean expression, writing Boolean sub-expressions next to each gate output in the diagram: C DD