b) The following shear stress – shear rate behavior was observed.Shear rate (Seconds-1)Shear Stress (dynes/cm?)20113015.24019.15022.96026.51.Make a plot of shear stress (ordinate) vs shear rate (abscissa) on log-log paper.2.Can the fluid behavior be accurately modeled by the Newtonian, Bingham plastic,or Power law model?

The given table is as follows, Draw the log-log table of shear rate and shear stress as follows:…

Answered: b) The following shear stress - shear…

b) The following shear stress - shear rate behavior was observed. Shear rate (Seconds) Shear Stress (dynes/cm2) 20 11 30 15.2 40 19.1 50 22.9 60 26.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Experimental measurements of relationship between velocity gradient and shear stress for different liquids are shown in the table given below. a) Plot the data on Excel and determine the fluid types. (Show your graph!) b) Which model do you use to describe the data? Specify the ranges of values for the coefficients. Velocity gradient Shear stress Fluid A Fluid B Fluid C 0.2 2.60 7.80 61.55 0.5 5.80 17.40 63.67 0.95 10.51 31.53 66.45 1.4 14.52 43.56 69.30 1.9 21.02 56.75 72.89 2.45 28.22 64.91 77.60 3.05 31.50 69.30 80.38 3.7 38.91 71.98 84.50 4.35 45.21 76.86 88.81 5.05 51.71 80.15 93.78
Fluid mechanics (Subject) Write legibly and sole neatly, show diagrams A surface vessel is 156 m long and moves at a velocity of 6.83 m/s. Determine the velocity of a geometrically similar model 2.44 m long be tested.a. velocity : ____________________ m/s
2. Casson model was discussed in class in the context of blood rheology. This phenomenological model is often used to describe the shear stress vs. shear rate relationship in colloidal suspensions where particle aggregation might cause the measured viscosity to increase at low shear rates. In an experiment, data for the shear stress and the applied shear rate S were fitted to the Casson model written below (in a slightly different form compared to that given in the lecture notes): √t = √²₁+√as. (1) The best least square fit parameters to the experimental data were found to be 40 mPa for the yield stress to and 2.5 mPa s for the parameter a, which is referred to as the plastic viscosity. a. Using Eq. (1), derive an expression for the fluid viscosity u as a function of S. b. Plot the viscosity of the fluid as a function of S for 0.1s¹ ≤S≤ 10 s¹. c. Based on class discussion on fluid classification, how would you characterize this fluid?
While using the Buckingham pi theorem to obtain non-dimensional groups, the repeated variables are chosen to be density, length and velocity and the non-repeat variable is angualr velocity. What is the non dimensional group that will be found in the form of : Non dimensional group= angular velocity x density ______x length ______x velcoity ________
Table 1 shows the variation of dynamic viscosities of water with absolute temperature. Table 1: Dynamic viscosity of water with absolute temperature. Viscosity µ, Pa.s x 10-³ 1.787 Temperature, K 273.15 278.15 283.15 293.15 303.15 1 313.15 333.15 353.15 373.15 4G 1.519 1.307 1.002 0.7975 0.6529 0.4665 0.3547 0.2828 a) Using excel software, develop a relationship of for viscosity in the form of μ=A+BT+CT² + DT³ + ET. Done Show your trend line regression and standard deviation for linear and polynomial index (quadratic T², cubic T³ and T). b) Using the relationship developed, predict the dynamic viscosity of water at 50 °C at which the reported value is 5.468 x 10 Pa.s. Compare your result with the results of Andrade's equation which is given in the form of μ = D.e BT where D and B are constants whose values are to be determined using viscosity data given.
a) Vortex shedding is a common fluid flow problem across bluff bodies. The design of buildings and bridges take into account the analysis of vortex shedding phenomena to avoid the occurrence of resonance, where the natural frequency of the body matches the vortex shedding frequency. In this analysis, the following parameters are found to be important: velocity of flow (V), density of fluid (p), hydraulic diameter of the duct (D₁), dynamic viscosity of fluid (u), width of body (B) and the vortex shedding frequency (n). Using the method of repeating variables, find the non-dimensional relationship governing the phenomena.
Saturated steam at 99.6 °C is heated to 350°C. Use the steam table provided to determine: a. The required heat input if 1 kg of steam undergoes the process in a variable-volume constant-pressure container. b. The work of expansion (in kJ) of the steam undergoing the process. C. The required heat input if a continuous stream flowing at 1 kg/s undergoes the process at constant pressure. d. Does your numeric answer to part c equal the sum of parts b and a? Explain why or why not. Given: 1 bar = 10 N/m4, Q= AH, Q = AU, AA = AÛ + PAV, table B.7 in kJ/kg and m/kg.
viscosity Pas 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 a) Do you think the sample in this graph is Newtonian, Shear-thinning, Shear-thickening? Upload a graph to support your answer. This Sample is _shear-thinning_ Viscosity against shear rate 0 2 4 6 shear rate 1/s 8 10 12 viscosity Pas 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 0 Viscosity against shear rate 2 4 6 shear rate 1/s 8 10 b) Do you think this sample has a yield stress? Input your estimate for the yield stress in mPa (If you think it does not have a yield stress, this value should be zero.) 12
1) At any time, approximately 20 volcanoes are actively erupting on the Earth, and 50–70 volcanoes erupt each year. Over the past 100 years, an average of 850 people have died each year from volcano eruptions. As scientists and engineers study the mechanics of lava flow, accurately predicting the flow rate (velocity) of the lava is critical to saving lives after an eruption. Jeffrey's equation captures the relationship between flow rate and viscosity as: Flow V = Pgt sin(@) 28 сm 10 where p is the density of the lava, g is gravity, t is the flow thickness, a is the slope, and u is the lava viscosity. Typical values are given as follows for the flow rate: u= 4x103 kg/(m.s) ±1% p= 2.5 g/cm³ ±1% t= 28 cm +0.5 cm a= 10° +1 ° g= 9.81 m/s? Determine the likely maximum possible error in the calculated value of the flow rate.
Which of the following parameters should not be selected as repeating variables in using Buckingham Pi theorem? (select all that apply) O a. Both pressure and shear stress O b. Both velocity and representative length O c. Angle
Assignment 3 On Viscosity Calculation - Word TOUT REFERENCES MAILINGS REVIEW VIEW Hyperlink P Bookmark tArt Chart Screenshot Apps for Office Online Video Cross-reference Comment Header Footer Page Number Text Quick WordA Box Parts - ns Apps Media Links Comments Header & Footer (2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av: = 10 cm/s, and the fluid is ethanol at 273 K having a viscosity of 1.77cp (0.0177 g/cm s). (a) Calculate the shear stress ty and the velocity (b) gradient of shear rate -/dy using cgs units. (c) Repeat using SI units. A Torce Fdshear berween teoparailel plates
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.