b- What is the crystal structure of an iron carbon 1.2% alloy that has been cooled from temperatures 1000-790-600 Celsius, and what are the proportions of the components at a temperature of 790 Celsius (illustrate this by drawing and extract the values using the lever rule).

b- What is the crystal structure of an iron carbon 1.2% alloy that has been cooled from temperatures 1000-790-600 Celsius, and what are the proportions of the components at a temperature of 790 Celsius (illustrate this by drawing and extract the values using the lever rule).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

evwVmpreun atatus: QUESTION 34 Consider a single crystal of RENE NS, a second generation Nbased superaloy. This alloy is used in the hottest part of gas turbine engines for aerospace. The matrix phase has a face-centered-cubic (FCC) crystal structure. This single crystal has been subjected to a tensile stress that is applied along a (314) crystal direction (aka, the axis f sip occurs on a (1 1 1) plane in a (101) direction, please cakulate the stress in MPa at which ylelding will occur. The critical resolved shear stress for this alloy is 800 MPa. cose Fo cos dcos (CRSS) (1SJos dcose 3184.3 O 41,600.0 O800.1 O 6368.7 579.0 400.1 Save A A es nit to sove ond subent. Cck Sae All A es to save dll ansers 3.
1000 grams of steel containing 1.5 weight percent carbon is heated to complete melting. After equilibrium is achieved, we slowly cool the alloy. Determine the amount of pure iron or pure carbon we need to add to this 1000 gram alloy if we need to have 100% pearlite at 720C upon slow cooling from complete melt.
Using the following table, draw a melting point diagram and estimate the eutectic temperature and composition: Percent composition Melting point range (°C) 100% A 125-126 75% A-25% B 115-120 65% A- 35% B 128-131 50% A- 50% B 135-140 100% B 151-152 Can you suggest what additional points you need to give a more accurate measure of the eutectic point?
If 500 g of a 40 wt% Ag-60 wt% Cu alloy is slowly cooled from 1000°C to just below 780°C (see Fig. 8.32): i. How many grams of liquid and proeutectic alpha are present at 780°C + AT? ii. How many grams of alpha and beta are present in the eutectic structure at 780°C - AT ? Atomic percent silver "C 10 20 30 40 50 60 70 80 90 F 1100 T 1084.5 1900 1000 961.93 1700 1600 1400 1200 1000 850 900- 800-a 700 600 500 400 L 10 Cu Figure 8.32 7.9 L+a 1 20 1 30 L 780 71.9 1 40 50 60 70 Weight percent silver- L+B 91.2 80 1 90 B Ag
The composition of the liquid in an 29 wt% griffinium alloy at 898 degrees centigrade is (enter the wt% griffinium)
4. Johnston and Gilman reported that in a grown LiF crystal that has been subjected to a constantstress of 10.8 MPa, the dislocation velocity at 249.1 K was 6×10-3 cm/s and at 227.3 K thevelocity was 10-6 cm/s. They also observed that their data suggested an Arrhenius relationshipbetween the dislocation velocity and the absolute temperature so that we can write? = ?exp ( ― ?/??)where v is the dislocation velocity, A is a constant of proportionality, Q an effective activationenergy in J/mol, and R is the universal gas constant (8.314 J/mol.K). Determine Q and A usingthe given data and the above equation. 5. A typical cross-head speed in a tensile testing machine is 0.2 in./min. (a) What is thenominal/engineering strain rate imposed by this cross-head speed on a typical engineering tensilespecimen with a 2 inch gauge length? (b) Estimate the average dislocation velocity that would be obtained at this strain rate in analpha-iron specimen with a total dislocation density of 1010 cm-2 of…
Referring to Figure 1, answer the following: What are the liquidus and solidus temperatures for an 80%Pb20%Tl alloy? What is the composition of the solid solution phase for the aforementioned alloy once we hit the liquidus temperature upon cooling? For the same alloy above, use the inverse lever rule to calculate the %solid and %liquid at 325C
A binary alloy having 28 wt% Cu and balance Ag solidifies at 779°C. The solid consists of two phases a and B. Phase a has 9% Cu whereas phase ß has 8 % Ag at 779°C. At room temperature these are pure Ag and Cu respectively Sketch the phase diagram. Label all phases and temperatures. The melting points of copper and silver are 1083 and 9610 respectively s Pà) Estimate the amount of a and B in the above alloy at 779°C and at room temperature.) b) Calculate the mass fraction of phases for 40% Cu alloy at 300 °C and TR c) What is the composition of the alloys in (b)
A Cu-Ni alloy must be fully liquid at 1350°C for processing. However,when placed in service the alloy must be solid at 1200°C. The phasediagram for the Cu-Ni binary system given below in Figure 3b.(i) Determine the composition range in which the alloy must lie.(ii) To obtain the maximum yield strength what composition shouldbe used?(iii) If, however, the highest elongation is required then whatcomposition should be used?
Moving to another question will save this response. uestion 37 Materials with dislocations have lower shear strengths than materials with no dislocations. Is this true or false? Moving to another question will save this response. L
For an alloy containing 20 wt % Ag, refer to the Cu-Ag phase diagram given in the Figure: What is the melting point of Cu in °C? What are the relative amounts(in %) of the existing phases at 900°C? Define the Eutectic point in terms of °C and the composition % of Ag.
Describe experimental procedure to obtain a binary isomorphic phase diagram for metals A and B by stating the equipment and materials you need? Show typical micrographs at 3 different phase regions for the alloy 50% A and 50% B on the phase diagram you obtained