b. A cart full of water is initially at rest on a smooth (frictionless) surface. Suddenly it starts ejecting water to the left (negative x-direction) at a constant velocity relative to the cart Vw/c. a. Immediately after the cart starts ejecting water, the acceleration of the cart is i. To the right Equal to zero To the left Cannot be determined ii. iii. iv. b. After some water has left the tank, you determine the cart has absolute velocity, Vc. The absolute velocity of the water leaving the cart is i. To the left ii. iii. iv. Equal to zero To the right Cannot be determined

b. A cart full of water is initially at rest on a smooth (frictionless) surface. Suddenly it starts ejecting water to the left (negative x-direction) at a constant velocity relative to the cart Vw/c. a. Immediately after the cart starts ejecting water, the acceleration of the cart is i. To the right Equal to zero To the left Cannot be determined ii. iii. iv. b. After some water has left the tank, you determine the cart has absolute velocity, Vc. The absolute velocity of the water leaving the cart is i. To the left ii. iii. iv. Equal to zero To the right Cannot be determined

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4: Determined the speed of block A in (Fig 2), if block B has an upward speed of 6 m/s. D Fig 2. B Fixed Point
Q4(a) A body starts from rest and accelerates at a rate of 2 m/s? for 5 seconds, then runs at a constant speed for next 60 seconds, and comes to rest after another 100 seconds. Determine total distance travelled by the body (b) Refer to Question Q4(a), if the body is travelling with a uniform speed of 20 m/s from start to end, critically evaluate its effect on the total time.
Q3. The 100 kg log is pulled by a constant tension force of 1000 N from rest. Determine the velocity of the log corresponding a distance of 3 m I am waiting for you, sir...
In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
PROBLEM 2.1 A car is traveling due west at 20.0 m/s. Find the velocity of the car after 3.00 s if its acceleration is 1.0 m/s² due west. Assume that the acceleration remains 1. constant. 17.0 m/s west 23.0 m/s west c. 17.0 m/s east d. 23.0 m/s east а. b.
4. Two blocks with the same mass are connected to a compressed spring at opposite ends. At first, the spring and blocks slide at the same velocity v on a frictionless surface to the right. The spring is released and at some later instant the left block is moving at v/2 to the left and the other block is moving to the right. What the speed of the center of mass of the system at that instant? (A) 5v/2 (B) 3v/2 (C) v (D) v/2
A steel ball was released from rest into a cylinder full of water. the downward acceleration up the ball is defined by the equation a=0.9g-CV. whose g is accelerating due to gravity. C=3.02/s. Det. the velocity in m/s after 0.25mins. a) Det. the dept of the ball from the water surface after 0.25 mins. b.) when of the following most nearly gives the acceleration of the ball when it reaches the bottom if the total height of the cylinder is 50 ft?
I Suppose an autonomous surface vessel (ASV) traveling with velocity TvG/O= vi₁ begins to make a turn by adjusting the thrust of its left and right thrusters, TA and TB, respectively. The center of mass of the ASV is located at G and the ASV is symmetric about its vertical axis. The ASV also experiences a drag force that is proportional to its speed and opposes its velocity. At the instant shown, the drag force is D = -kvi₁ where k is a drag coefficient. 1. To model the mass moment of inertia, approximate the ASV as consisting of three rigid bodies: a flat plate as a center body of mass 6m and two slender rods housing the propulsion assemblies, each of mass m, at the outboard sides of the vehicle. Determine the mass moment of inertia, IG, about the vertical axis passing through the center of mass G. (Hint: Use the parallel axis theorem.) 2. At the instant shown, determine the inertial acceleration vector ac/o = axi₁ + ayi2 of the center of mass and the angular acceleration a of the…
PROBLEM 2.24 29. A fighter jet lands on the deck of an aircraft carrier. It touches down with a speed of 75 m/s and comes to a complete stop over a distance of 200 m. If this process happens with constant deceleration, what is the speed of the jet 50 m before its final stopping location? 66.95 m/s 65.95 m/s c. 67.95 m/s d. 68.95 m/s a. b.
Q4. One ball of mass m = 1.4 kg is being swung in the vertical, circular path with radius of r = 2.9 m. At the instant shown, the ball is moving at a speed of v = 5.7 m/s. Determine the total acceleration of the ball (in m/s²) at this instant. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. Take g = 9.81 m/s². Your Answer: A 045° Answer
Q2. As shown in the image, a ball is confined to move along the smooth vertical slot due to the counterclockwise rotation of the arm OA. The ball contacts only one side of the slot at any instant. There is no need to solve for any answers for this problem: the goal is to demonstrate the strategy to solve the problem using cylindrical coordinates. On paper, draw the directions of the acceleration of the ball in radial and transverse components. Also, draw the FBD of the ball that shows its weight W, the normal force N exerted by the slot, and the force F from the rod, and write the resultant force components (involving W, N, F, and angle 0) in the radial and transverse directions. The accuracy and quality of the drawings are highly important and points will be taken for low-quality sketches. Take g = 9.81 m/s². Write in the answer space below "see notes". 6=2 rad/s 0.5 m A
OR Fig. 3 A robotic arm shown in Fig. 3 is programmed so that the 0.4-kg part A traces the radial path defined by r = 1–- 0.5 cos (2nt) meter and tranverse path of 0 = 0.5 – 0.2 sin (2nt) rad respectively. a) Calculate the velocity magnitude of part A at 1= 3 seconds. b) Determine the radial and transverse components of the force exerted on A by the robot jaws at 1= 2 seconds. Show the necessary Free-Body and Kinetic diagram to support your analysis.