B. Polar Coordinates 3. The partial surface of the cam and follower mechanism (used for the motion of intake and exhaust valves in automobiles) is that of a logarithmic spiral r = (40e0.050) in mm, where e is in radians. If the cam is rotating at a constant angular rate of è = 4dd, determine the magnitudes of velocity and acceleration of the follower rod at the instant of 0 = 30°. %3D rad %3D

B. Polar Coordinates 3. The partial surface of the cam and follower mechanism (used for the motion of intake and exhaust valves in automobiles) is that of a logarithmic spiral r = (40e0.050) in mm, where e is in radians. If the cam is rotating at a constant angular rate of è = 4dd, determine the magnitudes of velocity and acceleration of the follower rod at the instant of 0 = 30°. %3D rad %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the following mechanism, rod AB is pinned to the two disks at point A and point B, and the two disks roll to the left without slipping. if the length of rod AB, I= 2.4 m, and its angular velocity @ = 6.2 rad/s, determine the magnitude of the linear velocity of point B. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. (0.5 m 0.5 m No slipping No slipping Your Answer: Answer units
6. In the linkage below, the angular velocity of link 2 is 100 rad/s CCW. The linkage dimensions are given. When 02 is 90°, find 03, w3, and the velocity magnitude of point C on link 3 by using analytical method. A*A= 1.75 in A*B = 2.5 in AC = 5 in 02 B 3 Y 03 12 02 3 В A*
For the diagram below the angular velocity of the wheel is w = 2rad/s. The location of the instantaneous center of zero velocity is at point 0.3 m OD 1.2 m OB 45% O somewhere not listed in the other options. OC 0.3 m C
Show full solution pleaseFind the instantaneous velocity of slider F, in mm/s. The crank AB rotates inuniformangular speed of 150 rpm in counter clockwise direction. AB = 50 mm, BD = 400 mm, DC=150 mm, CE = 100 mm, EF = 95 mm, DC and CE are perpendicular. Drawin appropriate scale.(CLUE ANS: 341.6 mm/s)
1. The instantaneous angular velocity of the crank Q2A i - 3,600° counterclockwise. Q2A = 1.5 in. Find the second instantaneous linear velocity. And draw a graphical interpretation showing the proper length and direction of the velocity arrow of Q2A. Velocity scale: 0.5 in = 10 in/s. Drawing scale: 1:1 2.50 1.50 60° - 60°
For the following mechanism, rod AB is pinned to the two disks at point A and point B, and the two disks roll to the left without slipping. if the length of rod AB, /= 2.1 m, and its angular velocity W = 4.5 rad/s, determine the magnitude of the angular velocity of link AB. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. 0.5 m No slipping Your Answer: Answer 1 units 0.5 m No slipping
Q2/ In the mechanism shown in Fig. below the crank AOB rotates uniformly at 200 rev/min, in clockwise direction, about the fixed centre O. Find the velocity and acceleration of slider F. 200 rev/min DAF www Oby 315mm- 135mm 120mm 540mm 450mm 480mm- w F TIM 225mm 225mm
The linkage shown consists of 2 sliders, 1 bar, and a plate. The velocities of A and C are given to be VA = 2 m/s Vg = 3 m/s At the instant given. Find the velocity of point B. Use vector notation. 0.1m W1 rad/s 0.26m 12. rad/s VB m/s
In the figure shown, If v=800 mm/s, solve for the (a) velocity (in m/h) of D and (b) the angular velocity (in rpm) of AB. 320 mm 100 mm B 100 mm D -240 mm
vc = 3.60 Part A Due to slipping, points A and B on the rim of the disk have the velocities va = 7.2 ft/s and vg = 14.4 ft/s (Figure 1) Determine the velocity of the center point C at this instant. Express your answer to three significant figures and include the appropriate units. ft Submit Previous Answers Correct Part B Determine the velocity of the point E at this instant. Express your answer to three significant figures and include the appropriate units. Figure ft VE = |10.8 VB B Submit Previous Answers Request Answer 0.8 ft 45° X Incorrect; Try Again; 4 attempts remaining E CN 30° F A Va Provide Feedback
Find the velocity of slider D for the given configuration, if the link OA rotates at 1000 r.p.m. in clockwise direction. Dimensions of various links are as follows: OA = 150 mm 0Q = 225 mm QB = 200 mm 135 AB = 250 mm AC = 450 mm CD = 325 mm
The rod OA rotates clockwise at a constant angular velocity of 0 = (3) rad -. Two pin-connected slider block, located at B, move freely on OA. The curved rod is described by the equationr = (250 · (8 - cos 0)) m. Hint: 1. Remember clockwise rotation is negative velocity. A d3 d1 d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value 01 130 degrees di 0.45 m d2 dz 0.2 m 0.325 m Using cylindrical components, a. Determine the cylinders's radial and transverse components of velocity at the instant shown, vr and b. Determine the cylinders's radial and transverse components of acceleration at the instant shown, a, and ag. c. Determine the cylinder's magnitude of the velocity at the instant shown, v d. Determine the cylinder's magnitude of the acceleration at the instant shown, a