banrain is lOoking to design a v drive system for its recently instailed rolaly iachines. smaller pulley naving a dlameter connected to an electric motor and of nd. The belt is used to drive a larger pulley at a speed of 90 rpm. The V belt is used to transmits a power of 95 hp and ignore it in belt class selection process (Table 17.9). The servi / belt drive system is 1.3 and the suggested factor of safety for the current design is 2.5. Pulley Diameter = d = 9 in

banrain is lOoking to design a v drive system for its recently instailed rolaly iachines. smaller pulley naving a dlameter connected to an electric motor and of nd. The belt is used to drive a larger pulley at a speed of 90 rpm. The V belt is used to transmits a power of 95 hp and ignore it in belt class selection process (Table 17.9). The servi / belt drive system is 1.3 and the suggested factor of safety for the current design is 2.5. Pulley Diameter = d = 9 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A V-Belt drive is designed so that it has the input sheave on the shaft of an electric motor (normal torque) rated at .55 hp at 1160 rpm full-load speed. The drive is to a bucket elevator that is to be used 12 hours daily at approximately 675 rpm. The center distance is about 19.5 in. Add the detailed steps of your design to your attached worksheet. Hints: 1) In your design choose an appropriate belt section, specify the small pulley diameter, the large pulley diameter and the length of the belt. Determine the Belt length in inches, in two significant figures. Please enter below a numerical value only, no units are needed. Answer:
Help me please
A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input speed is 870 RPM and input power is 25 HP. Nominal output speed is 310 RPM. Design a V-belt drive and specify:(a) (b) (c) (d) (e)the belt size,the sheave sizes,the number of belts, theactualoutputspeed,the center distance. Show all your calculations.
A belt drive is to be used for transmitting 3KW from an electric motor whose speed is 1500rpm to a palm fruit digester running at 25rpm via a gear box. The speed of the pulley on the work shaft of the gear box is 300rpm. The digester operates at 8hours/day. 1. Select a suitable V-belt for the drive 2. Find the gear box reduction ratio
b) Base on your analysis, why the value of Belt Drive with V-Belt is having a lower coefficientcompared to flat belt?
3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving wheel = 1440rpm Speed of driven wheel = 400rpm Diameter of driving wheel = 300mm Center distance = 2500mm Service = 16hrs/day
A pump is driven by an electric motor through a open type flat belt drive.Motor pulley diameter (DS) = 300 mm, Pump pulley diameter (DL) = 600 mm. The Center distance between the pulleys=1000 mm. Find the length of the belt in inches
An industrial fan running at 600 rpm is driven by a 25kW, 960rpm, induction motor using an open belt drive. The pulley is mounted on the motor shaft of 270mm diameter. Center distance between the two shafts is 1.45 meters and coefficient of friction is 0.35. Assume thickness of belt equal to 6.5 mm and an allowable stress of 2.86MPa for belt material. Calculate the following: a) Angle of lap for both pulleys; b) Length of the belt; and c) Width of the belt (disregard standard size).
Design a chain drive to run a blower at 600 rpm. the power to the blower is available from a 8kw motor at 1500 rpm. the centre distance is to be kept at 800 mm.
Please show step by step manual solution and diagram for Machine Elements 2 problem below. .A pulley 600 mm. in diameter transmits 40 kW at 500 rpm. The arc of contact between the belt and pulley is 144°. Determine (a) diameter of the driven pulley for open belt drive, (b) diameter of the driven pulley for cross belt drive, (c) speed of the driven pulley, (d) belt length for open belt connection, and (e) belt length for cross belt connection.
A conveyor is driven by a 2.5-hp high-starting-torque electric motor through a flexible coupling to a worm-gear speed reducer, whose speed ratio is 35, and then via a roller chain to the conveyor shaft that is to turn about 12 rpm; motor rpm is 1750. Operation is smooth, 8 hr./day and service factor can be taken as 1.2. Decide the chain pitch in inch.
Q2: A speed reducer unit is to be designed for an input of 1.1 kW with a transmission ratio 27. The speed of the hardened steel worm is 1440 r.p.m. The worm wheel is to be made of phosphor bronze. The tooth form is to be 20° involute. Given data: the centre distance (x) = 100 mm. Draw complete construction of the system showing all missing parts, i.e. keys, bearings...etc, with necessary mountings and fixations. (Put the main dimension). Assume suitable missing dimensions or data if any.