Bond, Anchorage and Development Length Question 1: How much shall be the development length of 25 mm diameter deformed reinforcing bar of grade Fe415 in tension? (Given that design bond stress in limit state method for deformed bars in tension = 2.24 N/mm²) 1. 762.9 mm 2. 1220.6 mm 3. 1007.39 mm 4. 849.5 mm

Bond, Anchorage and Development Length Question 1: How much shall be the development length of 25 mm diameter deformed reinforcing bar of grade Fe415 in tension? (Given that design bond stress in limit state method for deformed bars in tension = 2.24 N/mm²) 1. 762.9 mm 2. 1220.6 mm 3. 1007.39 mm 4. 849.5 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.3P: A tensile test was performed on a metal specimen having a circular cross section with a diameter 0....

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
The following data was obtained from a tensile test on Load (kN) 16 32 56 72 95 110 132 142 140 135 Extension (mm) 0.2 0.4 0.7 0.9 1.5 2.5 5.0 8.5 10.0 12.0 a specimen of 10mm diameter and gauge length 60mm. Using the graph paper supplied, plot the load-extension diagram and determine: (1) The tensile strength (2) 0.1% Proof Stress (3) Young's Modulus for the specimen
Sample: Malleable Steel (AISI 4145) Original Diameter: 6.14mm Gauge Length: 55 mm Final Length: 68.12 mm Final Diameter: 3.54mm Load (kN) Deformation (mm) Stress (MPa) 12.95 Strain (%) 0.3838 0.54 0.7841 0.95 26.48 1.3899 1.63 1.9485 2.07 3.3090 3.10 4.5821 4.22 5.9359 5.03 7.0340 5.51 8.2413 6.22 10.9446 7.22 13.1951 8.18 12.8228 8.77 12.2583 9.11 12.5915 9.61 13.2536 10.33 13.6636 10.71 13.9772 11.35 14.5433 12.63 15.1155 13.88 15.4970 15.10 15.6484 17.09 15.4031 17.79 14.7655 18.73 13.6721 19.28 10.4617 19.88
A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in TableUsing a spreadsheet program obtain the following:a. A plot of the stress–strain relationship. Label the axes and show units.b. A plot of the linear portion of the stress–strain relationship. Determine modulus of elasticity using the best-fit approach.c. Proportional limit.d. Yield stress.e. Ultimate strength.f. If the rebar is loaded to 390 kN only and then unloaded, what is the permanent change in length?
Q2/Show the mechanical properties changes during tensile test of a metal specimen. Write the mathematical relationships. 443X
100 types of steel failures
A 32-mm rebar with a gauge length of 200 mm was subjected to tension to fracture according to ASTM E-8 method. The load and deformation data were as shown in Table P3.33. Using a spreadsheet program obtain the following: a. A plot of the stress-strain relationship. Label the axes and show units. b. A plot of the linear portion of the stress-strain relationship. Determine modulus of elasticity using the best-fit approach. c. Proportional limit. d. Yield stress. e. Ultimate strength. f. If the rebar is loaded to 390 kN only and then unloaded, what is the permanent change in length? TABLE P3.3 3 Load (kN) Displacement (mm) Load (kN) Displacement (mm) 472.9 8.4 62.2 0.1 487.1 9.7 188.9 0.2 496.4 11.1 329.8 0.4 505.7 12.4 383.4 1.7 512.8 13.7 426.0 4.0 522.6 15.3 447.3 5.9 532.4 18.5 462.5 7.2 525.9 22.4
Class work I diameter Given: metal specimen x-section (circular) = 0.55 in. Gage length = 2.030 fm. in. Fracture occurred at pounds # final length final dia. Determine 28,500 € = 2.30 in. = 0.43 in. tensile stress in kşi c) Reduction of x-sect, area a percentage pricentage as a a) Ultimate 6) Elongation as Note: Gaye length - length over which elongation is measured all
A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the modulus of elasticity. 120 Upper scale 90 60 Lower scale 30 0.040 0.004 0.060 0.006 0.120 0.012 0.020 0.100 0.010 0.0 0.080 0.008 0.0 0.002 Strain (in./in.) Stress (ksi)