C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will be the size of wind turbine that is required to be installed to meet the energy requirement. Following assumptions are taken into account for estimation: Annual energy requirement = 20900 kWh Propeller type wind machine is used Coefficient of performance = 0.40, Loss factor value = 0.325 Wind speed at 6 meter/sec (This wind speed should be taken from the wind data prepared for that location.) Density of air = 1 kg/m? Capacity factor = 0.30 (i.e. 30% of the time, wind machine is producing energy at rated power) Number of hours in a month 730 hours. Annual energy density = Radius of rotor = Turbine Rating =

C2(i)Assume that annual energy requirement of an industry is 20900 kWh ,we calculate that what will be the size of wind turbine that is required to be installed to meet the energy requirement. Following assumptions are taken into account for estimation: Annual energy requirement = 20900 kWh Propeller type wind machine is used Coefficient of performance = 0.40, Loss factor value = 0.325 Wind speed at 6 meter/sec (This wind speed should be taken from the wind data prepared for that location.) Density of air = 1 kg/m? Capacity factor = 0.30 (i.e. 30% of the time, wind machine is producing energy at rated power) Number of hours in a month 730 hours. Annual energy density = Radius of rotor = Turbine Rating =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 20 kVA machine has a full load copper loss of 400 W, an iron loss of 150 W, and a mechanical loss of 200 W. Determine:a) Efficiency at 3/4 of full load with f.d.p. 0.8. Ans: 95,43%b) Performance at full load with f.d.p. 0.9. Ans: 96%c) Peak performance apparent power. Ans: 18,71 kVAd) Yield in the previous case for f.d.p. Unit. Ans: 96,39% I need the procedures to get these results. Thanks
A wind turbine model has the following power curve: 5 10 15 20 25 30 Wind speed a) From the power curve above, estimate the value of the following: Cut-in speed = Cut-out speed = Rated speed = Rated power = b) If radius of this turbine is 25 m and air density is 1.2 kg/m³, calculate the coefficient of power at rated speed c) The wind speed distribution for the location of the wind turbine is shown below. Determine the power output for the given wind speed (using the wind turbine power curve above) and calculate the total annual electrical energy output. Produced power of wind turbine [MW]
Refer here for the specifications of the D400. a) What power output should you be able to supply from the 24V D400 at 15.4 m/s? b) If the wind drops to 2 m/s, what will the output power be? c) According to the performance graph what is the maximum power you can obtain from the 24V D400? There is a possibility of installing the turbine on top of a 20m high mast instead. Assuming that Zo=0.012, what would you expect the wind speed to be at that height? Use wind shear formula and assume Vref = 7.5 m/s at a height of Zref =10 m.
Draw and explain a typical power curve for a wind turbine and write the definition of the four important terms that are shown in the power curve
• A DC shunt machine while running as generator develops a voltage of 250 V at 1000 r.p.m. on no-load. It has armature resistance of 0.5 ohm and field resistance of 250 ohm. When the machine runs as motor, input to it at no-load is 4 A at 250 V. Calculate the speed and efficiency of the machine when it runs as a motor taking 40 A at 250 V. Armature reaction weakens the field by 4 %
(a) Draw and explain a typical power curve for a wind turbine and write the definition of the four important terms that are shown in the power curve. [ (b) Explain any three factors which affect the efficiency of a wind turbine.
Discuss about the performance characteristics of wind turbine
Please answer with step by step math for Zin, Zout, and the load voltage. Thank you!
Consider a wind machine designed to deliver its rated power at the average velocity fora given wind spectrum. It will be marketed for sites having wind velocity spectra thathave the same annual average velocity but with Weibull statistics ranging from k = 3/2to 5/2.a. Calculate the ratio of maximum to minimum annual average on-site wind poweravailable for exploitation for this range of wind fields.b. What additional assumptions are necessary if the power actually produced is tobe in the same ratio as in (a) above?
Q9/ Complete the blank Commutator in DC machine is made up of .....................................?
Find the rolling force and its power. The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
Explain binary cycle power plant (using figure). Compare its performance as compared to other geo-thermal power plants.