The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, if the allowable stress for the steel in this application is = 160 MPa, and the diameter of AC: d = 22 mm. Calculate the largest load p on AB in order to keep AC safe: pmax = ____ kN/m.Calculate your answer to 1 decimal place. The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the= 160 MPa, and the diameter of AC: d = 22 mm. Calculate the largestdesign of AC only, if the allowable stress for the steel in this application is(allow)load p on AB in order to keep AC safe: Pmax=kN/m.Calculate your answer to 1 decimal place.p kN/m2 m.B

Uniformly distributed load:- Force is evenly distributed over the span of beam It is given that,…

Answered: Calculate the largest load p on AB in…

Engineering

Mechanical Engineering

Calculate the largest load p on AB in order to keep AC safe:

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.7.10P: Three round, copper alloy bars having the same length L but different shapes are shown, in the...

See similar textbooks

Related questions

Q: Problem 4: Determine the moment created by the three forces shown in the figure below about point B.…

Q: Q4. 0.3 m³ of air at a pressure of 3 bar is expanded to a volume of 0.708 m³and temperature 160°C.…

Q: The 35°C water flow of the Figure below discharges to sea-level standard atmosphere. Neglecting…

A: Given: T=35°Cd1=1 ind2=3 ind3=D inH=6 ft

Q: Serious neck injuries can occur when a football player is struck in the face guard of his helmet in…

A: Given data: P=50 lb

Q: In the figure, aluminum [E = 68 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: A 60-lb aluminum bar, initially at T₂ = 150°F, is placed in a tank together with 190 lb of liquid…

Q: A water jet traveling at a velocity of 30 meters per second collides with a splitter plate, causing…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A: Given data: E= 30000 ksicross sectional area A =1.5 in2a=40 inb=64 inc=24 inL1=55 inL2=100 in normal…

Q: Steps on autocad

A: Given 2D sketch To find Steps

Q: The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of…

Q: 13 ст 2 X Com This pic is with d 29 см NNY T 26cm right Triangle that made from Iron rody P 8 11…

A: Given Data: Length of the base of triangle B=26 cm Length of the height of triangle H=13 cm Length…

Q: 4- If rod AB slides along the horizontal slot with a velocity of 60 ft/s, determine the angular…

Q: Please show steps how you come up with rate of heat transfer

Q: Q9. The platform is rotating about the vertical axis such that at any instant its (C₁. ³/2) rad,…

A: Find the magnitude of velocity at t = 1.7 sec

Q: A workpiece turning at 20 rad/sec has a diameter of 4 inches. Find the peripheral speed of the…

A: Given:Angular speed of the work piece, ω=20 rad/sDiameter of the workpiece, d=4 in

Q: Select one: a. Running an NC part program without touching the stock. Ob. The first time that a new…

A: introduction; A dry run is used for testing of machine program by cutting of air.

Q: A projectile is launched from point A with the initial conditions shown in the figure. Determine the…

Q: Using the tables for water determine the specified property data at the indicated state. For H2O at…

A: Given data:-H2O at T = 40 °C and X = 71 % To find :- specific volume (v) in m3/kg

Q: A velocity field is given by u-V cosa, v= V sinx and w=0. The equation for streamline will be: y=x…

A: Option A is correct

Q: Q13. The collars are pin connected at B and are free to move along rod OA and the [C. (1 + cos 0)]…

A: Given data r = C.(1+costheta) C = 0.2 theta = 0.9 rad. Find the velocity of collar.

Q: Bar OA has the angular motions of 3.4 rad/s, and 7.2 rad/s2 is shown. If angular velocity of Bar AB…

A: let angular velocity of W2 and and angular velocity of AB is w3 so ω2=3.4rad/secω3=1.21rad/sec…

Q: Q19. As shown in the image below, the 2.7-Mg four-wheel-drive SUV tows the 1.1- Mg trailer. The…

Q: A heating system is to be designed to keep the wings of an aircraft cruising at a veloeity of 900…

Q: Where is the Energy Balance?

A: to find energy balance we need to write the mechanical energy conservation equation i.e. bernoulis…

Q: Determine the x, y, and z components of the moment of the force of F=570 N about point A Express…

A: Write the 3D co-ordinates of points A, B and C. A=0,0,4B=4cos45°,0,4sin45°=2.83,0,2.83C=6,6,0

Q: Q6. The 9-kg ball is connected to a spring with spring constant k = 100 N/m and unstretched length…

A: The force responsible for the motion of the ball can be determined as shown below.

Q: The 20-kg crate is lifted by a force of F = (100 + 5t2) N, where t is in seconds. (Figure 1) Figure…

A: Given data Mass of crate = 20 kg Force F = (100 +5t2) N Determine how high the crate has moved…

Q: The car C and its contents have a weight of 630 lb, whereas block B has a weight of 230 lb. The car…

A: Given data weight of block =230 lb weight of car =630 lb

Q: CHAPTER FOUR Equilibrium of Coplanar Forc 4.13 Calculate the horizontal force F that should be…

A: Given data Weight = 100lb Angle = 30° with the vertical. Find the force F

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

Q: For has the instant represented, crank Counterclockubise of w=0.9 rad/s a acceleration respectively…

Q: Which of the following AISI material category designations refers to plain carbon steel? AISI…

A: as per AISI, First digit indicate whether is it plain carbon steel or not? second digit indicate…

Q: The following figure shows five forces act at point A. Calculate the magnitude of the resultant…

Q: how to get mass (in lb/m) if given weight is 960 lb. Please show the proper conversion of units when…

A: Given :- Weight = 960 lb To Find:- Mass (m) in lbm

Q: Two beams at 6 meters in length each are arranged so that the reactions at A, B, and D are the…

Q: Two forces F₁ and F2 act on the screw eye. If their lines of action are at an angle 9 apart and the…

A: Given-Information:- F1 = F2 = F To-Determine:- 1. Magnitude of Resultant Force FR2. Angle Between…

Q: 9 in. 30° 6 in. 3 in. 3 in. 3 in. 4 in. The top cylinder weighs 100 lbs., the middle cylinder weighs…

Q: Determine the moment produced by force FB about point O. Point O is at the base of the pole as…

Q: A piston-cylinder set up for an experiment has 30L (50% liquid, 50% vapor by volume) of water inside…

A: Write the given data. V1=30 Lx=0.5P1=300 kPaV2=2V1T2=150 °C

Q: As shown in the figure below, a reversible power cycle receives energy QH by heat transfer from a…

A: Given data A reversible power cycle Find the thermal efficiency and temperatures

Q: The loading and unloading response of a metal is shown in the figure. What is the elastic and…

Q: The 23-kgkg disk, is pinned at its mass center OO and supports the 5-kgkg block AA. The belt which…

A: Introduction In this problem, we will use the equilibrium state of the disc to compute the time…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

A: The given information in the problem is listed in the following attached image:

Q: The 23-kg disk, is pinned at its mass center O and supports the 5-kg block A. The belt which passes…

A: Given data mass of disk = 23 kg Mass of block = 5 kg Find the natural frequency of the system.

Q: = Q8. The 3.1-kg, uniform crate starts from rest to slide down the inclined surface. If the…

A: Given data:- Mass of the crate =3.1 kg μk=0.12 g=9.81 m/s2 and S=2.7 m To find:- Work done by…

Q: A steel [E = 30,300 ksi; a = 6.7 x 106/°F] pipe column (1) with a cross-sectional area of A₁ = 5.70…

Q: The wheel is spinning about shaft ABAB with an angular velocity of ωs=10rad/sωs=10rad/s, which is…

A: Given data: ωs=10 rad/sω˙s=6 rad/s2ωp=12 rad/sω˙p=3 rad/s2 Need to determine the velocity and…

Q: Which of the following could not be obtained directly from the stress-strain diagram from a tensile…

A: Draw stress - strain diagram and find which property from the following is not obtained from the…

Q: Diagram Q ww Water, 90°C x = 0.10 1-kg of water that is initially at 90°C with a quality of 10…

Q: Q15. As shown on the right in image below, the force Facting on the box varies with time t, and the…

A: Since the variation is linear for the duration of 0.3 second to 1 second, the impulse can be…

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the design of AC only, if the allowable stress for the steel in this application is = 160 MPa, and the diameter of AC: d = 22 mm. Calculate the largest load p on AB in order to keep AC safe: p_max = ____ kN/m.

Calculate your answer to 1 decimal place.

The rigid bar AB shown below is supported by a steel rod AC having a diameter of d mm and a block. Ignore the weight of AB and AC. Consider the
= 160 MPa, and the diameter of AC: d = 22 mm. Calculate the largest
design of AC only, if the allowable stress for the steel in this application is
(allow)
load p on AB in order to keep AC safe: Pmax=
kN/m.
Calculate your answer to 1 decimal place.
p kN/m
2 m.
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem for sx= 11 MPa and ??y= -20 MPa (see figure).
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.
A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
QUESTION 4 Figure 3 below shows a vertical rod under its own weight. Find the displacement at A and stress distribution. Use E-100 MPa and weight per unit volume 0.06 N/cm³. Solve using two elements and comment on the stress distribution. 1.6 m 1m A Area = 2500 cm² 8 B Area = 1500 cm²
A rod of different materials is arranged as shown with the corresponding axial forces (see figure 3). Find the maximum value of the force P in kN such that it will not exceed a stress in steel of 140,000 kPa, in aluminum of 90,000 kPa, or in bronze of 100,000 kPa. INPUT THE NUMERICAL VALUE ONLY IN 3 DECIMAL PLACES
The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block. Ignore the weight of AB and AC, and the distributed load on AB is p = 4.0 KN/m. Determine the axial normal stress developed in AC: = ____ MPa. Calculate your answer to 1 decimal place.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take d₁ = 30 mm, d2 = 50 mm, and P = 50 kN. P 0.9 m 125 kN 125 KN B 1.2 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is MPa.
A hollow cylindrical column is placed on a steel plate on a concrete pedestal, if it supports a compressive load of 0.75 MN as shown in the figure and the stress in the column is limited to 55 MPa, Calculate the desirable wall thickness of the column given that the diameter of the outside wall is 25 cm. Column ANS: Base plate mm (one decimal place)
Compute the maximum stress in the member, considering stress concentrations. Use Figure P3-66 2.00-in dia. 0.10-in radius 1.25-in dia. Applied torque = 2200 lb-in
PROBLEM: Find the values and plot the distribution of stress over the cross section of the upright of the figure. Locate the point of zero stress. 9,000 N 60 mm thick 100 mm 50 mm