Calculate the value of R shown in Figure 1

Q: Specific speed of a kaplan turbine

A: Given; Kaplan turbine are the turbine which works on axial flow reaction. In this turbine water flow...

Q: Find the resultant of two forces equal to 50N and 30 N acting at an angle of60°

A: Given Forces F1= 50 NF2= 30 NAngle = 60 To find Resultant

Q: The spanner shown is used to rotate a shaft. A pin fits in a hole at A, while a flat, frictionless s...

A:

Q: A particle travels along the circular path x2 + y2 = r2. If the y component of the particle's veloci...

A:

Q: and max. B.

A:

Q: modulus of ln (2 +3 j)?

A:

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is...

A: Given data: Diameter of tank =D =3.75 ft = 45 inThickness =t = 0.3750 inLimiting stress =σ = 3750 ps...

Q: 7 m B 10 m 40° 2 m 35 1.5 m 8 m

A: Newton's equation of motion can be written as, v=u+ats=ut+12at2v2=u2+2as Here, v is the final veloci...

Q: A stone was dropped from a hot air balloon when the balloon was 93 m from the ground (ascending at a...

A:

Q: A bronze bar is fastened between a steel bar and aluminun bar as shown. Find the largest value of P ...

A: Given:As=480 mm2Ab=650 mm2Aa=320 mm2Es=200 GPaEa=70 GPaEb=83 GPa

Q: Water is to be supplied to the inhabitants of a college hoste through a supply main. The following d...

A: Given:L=4000 mn=3000Water consumed per day, q=180 Lhl=18 mf=0.007t=8 hrs

Q: ow. Find out the value of "K" such that the system will be in the stable region.

A: Need to find the value of K

Q: find the velocity (in m/s)

A:

Q: A container 10 m wide and 10 m long contains water 2 m high and is accelerating to the right at a ra...

A:

Q: (a.) A fluid at P1, V1, flows through a sudden 2:1 contraction, with Az/A1 = 1/2 (see figure below)....

A: given; A2/A1=12KL=0.25∆P=P2-P1

Q: 1. The kinematic viscosity of kerosene is 9 = 2.39(10-6). Determine its viscosity in FPS units. At t...

A: Givenkinematic viscosity of kerosene ϑ=2.39×10-6 m2/sspecific gravity sgkerosene=0.810

Q: Mass of ball=2.1 kg Velocity of bas=2.2 m/s Determine kinetic energy

A:

Q: ur instantaneous velocity is 219 kph. Det a. The acceleration of your boat b. The acceleration of bo...

A: Need to find Acceleration of Bots.

Q: A 105 x 205 mm reciprocating R134a compressor operates with a suction pressure of 0.2928 MPa and a c...

A: Note: As per policy, we can solve the first three subparts. Please resubmit the remaining parts.Refr...

Q: A fixation plate (thickness 3 mm, width 40 mm) has a circular hole of radius 5 mm. The plate contain...

A:

Q: If the length of a column is doubled, the critical load becomes ?

A:

Q: Force applied-7 N Displacement=3 m Determine work done

A:

Q: 10 Ibm/min of Steam at 4.5 MPa with a moisture content of 7% undergoes a constant volume process unt...

A:

Q: Force applied=7 N Displacement=3 m Determine work done

A: Given data : Displacement=S Force=F   Required Work Done

Q: Problem 11.032 - Second law analysis of ideal vapor refrigeration compression cycle NOTE: This is a ...

A:  

Q: A centrifugal pump is required to pump water t an open water tank situated 4 km away from the locati...

A: Given:L=4 kmd=0.2 mf=0.01v=2 m/sh=5 m

Q: 5. Steam at 200 "Cand with an entropy of 5.6105 KI/kg-Kexpands isothermally to 0.515 MPa. Far 5 kg (...

A: Since we only solve one question, we will solve the first one. Please resubmit the question and spec...

Q: 80 kN

A:

Q: A bar of a steel alloy that exhibits the stress–strain behavior shown in Animated Figure 7.34 is sub...

A: Given data: Specimen length = 375 mm = 0.375 mCross section = 5.5 x 5.5 mm2 = 30.25 mm2 

Q: FOS-?

A: Given; A machine element is subjected to the following bi-axial stress:  σx=75 MPa σy=15 MPa ζxy=35 ...

Q: efficiency (expressed in decimals, such as 0.25; don't write 25%) of the pump is ?

A: Need to find efficiency of pump.

Q: what is the term that refers to the total energy content of a system in the topic of Thermodynamics?

A: The system consists of any liquid or gas which is under the observation and everything else is calle...

Q: Assuming the end of C is moved 10mm downward by a load P on the beam, determine the normal strain de...

A:

Q: 1.39 The bar AB is supported by a frictionless inclined surface at A and a 7/8- in.-diameter pin at ...

A:

Q: Question 2: For the following truss structure (with members AB, BC, AD, DE, BE, CF and FG all of 60 ...

A: Find the force in memeber DE

Q: ‘Hydraulic lift’ works on the basis of

A:

Q: VE FUNCTIONS OF EACH COMPONENTS

A: we have to discuss functionality of different parts of tensile strength test.

Q: the velocity of boat A relative to boat B.

A: Determine the velocity of BOAT A relative to B

Q: 4. Determine the internal normal force, shear force, and bending moment at point C in the beam. 10 K...

A: Answer: ◆ Internal Normal Force at C: NC = 0 kN. ◆ Shear Force at C: VC = 20 kN. ◆ Bending Moment at...

Q: the critical load becomes

A: Given; If the length of a column is doubled ;the critical load;   P=π2EIl2  

Q: As shown in the figure below, determine the internal loadings at points D and. Consider the weight o...

A: given: FN = 70lbs SN = 50lb/ft

Q: A ball is released from the bottom of an elevator which is traveling upward with a velocity of 6 ft/...

A:

Q: The radius of a highway curve is 120m, and has an angle of 9.31 from the horizontal. The center of g...

A: Given data as per question The radius of a highway curve = 120m Angle =9.31o Distance between the tw...

Q: 2. Assuming the end of C is moved 10mm downward by a load P on the beam, determine the normal strain...

A:

Q: 6. Find the C.O.P. of a refrigeration system if the work input is 30 KJ/kg and refrigeration effect ...

A: From the data given in question, Work input = W = 30 kJ/kg Refrigeration effect = QR = 120 kJ/kg   C...

Q: Question 3: For the following truss structure (with members AB, BC, AD, DE, BE, CF and FG all of 60 ...

A: Find the force in member AE  

Q: During inelastic collision of two particles, which one of the following is conserved ? 1. total line...

A: Let us first understand which quantity is conserved in which type of collision. In all types of coll...

Q: GIVE FUNCTIONS OF EVERY COMPONENT IN UNIVERSAL TESTING MACHINE (ALL PARTS_

A: A universal testing machine (UTM) is a machine that uses tensile, compressive, or transverse stresse...

Q: Truss detail Member=9 Joint%3D6 Reaction34 Is truss formed is sta

A:

Q: The instantaneous angular velocity of the crank Q2A is 3,600° counterclockwise. Q2A = 1.5 in. Find t...

A:

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.