Capacitor proximity sensors: are actuated by both conductive and nonconductive materials. are actuated by conductive materials only. produce an electromagnetic field. have a long sensing range.

Q: A 3-phase 400 volt, balanced star connected lagging load take a current of 5A. The power is…

A: Given- 1 3-phase 400 volts, balanced star connected lagging load with, Current, I=5 A. The power is…

Q: ३६ 6 O a. R O b. 16 OC. SR O d. O In the above circuit, what is the current through the resistance…

A: here we have to find the current through the resistor R.   given circuit is  consider a node 'a' as…

Q: The waveform shown in Figure 1c is passed into an Ideal Low Pass Filter (ILPF) which has a cut-off…

A: Given the signal as shown below: The waveform shown in Figure 1c is passed into an Ideal Low Pass…

Q: 1) a) Consider the circuit below consisting of a battery and five identical bulbs. Rank the…

A: Need to analyze the brightness of the battery based on the given connection and need to order them…

Q: (a) After the switch is first thrown to a (connecting the battery), what time interval elapses…

A: For the given RL circuit the value of time required to reach 220mA, Value of current at t-10s and…

Q: Question: A communication satellite is transmitting a signal to a ground station on Earth. The…

A: Given data: Frequency (f) = 10 GHz = 10,000 MHz Transmit power (Pt) = 50 watts Distance (d) =…

Q: 4. For the system in Figure P4, sketch the root locus and find the breakaway and break-in points.…

A: Given Data: An open-loop transfer function of, Gs=Ks-3s-5s+2s+4 And the feedback of, Hs=1 To Find:…

Q: 7. Consider the Laplace transfer function: H(s) = 3(s+1) (s+5) (s+3) i. Express H(s) under a…

A:

Q: 2- Given the following two-degrees of freedom translational mechanical system, use the "by…

A: The transfer function of the given mechanical translational system needs to be calculated by using…

Q: Draw a dysfunctional circuit. Why is the circuit not functional?

A: It means that the circuit is not operating in normal conditions. Or in other words, we can say that…

Q: (b) A sinusoidal information signal of frequency 800Hz is used to frequency modulate a carrier…

A:

Q: Two power system areas operating at a nominal frequency of 60 Hz are connected with a tie line, and…

A:

Q: a) i) Sketch the sequence x[n] = cos (n. π/2) plotted against 'n' (the sketch should only go from n…

A: Given Data: A sequence of xn=cos nπ2, -2≤n≤3 The input and impulse sequences of, xn=12n hn=12,…

Q: TOOT 10 6v ² 2002 52 Find RT for the circuit Show below

A: here we have to find the total resistance.   we have taken that the all the resistors given in the…

Q: c) If in figure 2.1 the Q-point is given, VGs = -2 V, IG= 0 mA, VDs = 10 V, IDs = (4.XY) mA, then…

A: DC analysis of the amplifier will here XY=54,VGS=-2V,IG=0mA,VDS=10V,IDS=4.XY mA…

Q: In the two circuits, identify i₁(t), represented in the time-domain form. i₁ (t) = 70cos (10t + 30°)…

A: In this question We need to determine the current i1(t) as shown the circuit.  We are solving this…

Q: Let the line voltage V₁ = 208 V and the wattmeter readings of the balanced system in Fig. 12.35 be…

A: It is given that: VL=208 VP1=-560 WP2=800 W

Q: a) What is the major difference between a CG FET ac amplifier and the other two FET ac amplifier…

A: Step-1-> CG FET, CS FET, and CD FET are different types of field-effect transistors (FETs) that…

Q: b. Find the current flowing through 20 52 resistor by first finding a Norton's equivalent circuit.…

A: We need to find out the current through given resistor by using of Norton equivalent circuit.

Q: A 4-bus network having the following L & U matrices: [-j16.75 j11.75 j2.5 j2.5 L U= Z42 is: ܘܘܘܟ 0…

A:

Q: nodal Analysis prob 3 find V, at mode n1, V₂ at node n₂

A: For the given circuit the value of node voltage V1 and V2 needs to be calculated by using the nodal…

Q: Calculate the geometric mean radius (GMR) for the arrangement of parallel conductors shown below if…

A: here we have to find the Geometric mean radius.

Q: An 11 KV generating station has four identical 3-phase alternators A,B,C and D and each of 10 MVA…

A: Here,  Every generator is having a reactance of 0.12 Pu G1∥G2=0.12∥0.12=0.12×0.120.12+0.12=0.06…

Q: A 400 MVA synchronous machine has H₁ = 4.6 MJ/MVA and a 1200 MVA machine has H₂=3.0 MJ/MVA. The two…

A: It is given that: H1=4.6 MJMVA ,S1=400 MVAH2=3.0 MJMVA ,S2=1200 MVASbase=100 MVA

Q: The reference angle of (3\pi )/(2)rad is (\pi )/(2)rad.

A: When the desired angle is in the third quadrant (angles from 180° to 270°), our reference angle is…

Q: Example: Determine @o, @max When R=5092 and R = 19 R 50mH L 5μF

A:

Q: Find power dissipated across R1 in mW V₁=8,8Volts, and R₁ =5,4k V1 Si Ge R1

A: V1=8.8 V, R1=5.4 kΩ. Given circuit diagram is,

Q: 70 V + 20 Ω Μ O 301-1012-2013--70 Ο 301 – 10+2 + 2013 = 70 Ο 3021 – 1072 – 2013 – 70 3011+1012-2013…

A: to find the KVL equation for the mesh 1 in the given circuit.…

Q: Find the Norton's equivalent circuit of the circuit in the figure below at terminals a-b. Draw the…

A:

Q: Question 1. An industrial load consisting of a set of induction motors connected to a 220 V 60 Hz…

A:

Q: 9. Simplify Y = AB' + a) AB' + C b) AB + AC c) A'B + AC' d) AB + A K (A B)C

A: It is given that: Y=AB'+A'+BC

Q: What is the scaled value of the capacitor? Express your answer to three significant figures and…

A: For the given circuit, the value of scaled capacitor, frequency for scaling and the ration between…

Q: 1. Fixed Bias Configuration 15V ITC 160ko 1.2k₂ Is Determine: Vor B=100 IB, IC, VCE

A: it is asked to find IB,IC, VCE for given circuit

Q: Final answer is already given in the given photo below so just kindly provide a COMPLETE and CLEAR…

A: Cs=9ss2+2s+9

Q: 4) Two single phase transformers in an open delta bank served a 3 phase balanced load of 100 KVA. If…

A: Rating of transformer S = 100 KVA. Initially two single phase transformers are there then one…

Q: Do the operations by taking two digits in the part of the decimal number after the dot. Do not…

A: Solution: Given data: 3- phase Delta -connected Z=40 ohm<30(degree) Voltage=374 V Angle= 140…

Q: 5. Use matrix analysis to find nodal voltages, V₁, V2, V3, for the circuit shown in Figure 5. 2 A V₁…

A: In this question We need to determine the voltages at the nodes as shown the circuit.  We are…

Q: 165 km three-phase walking line 55 MVA transmits power at 132 kV voltage (in-phase) to the load with…

A: Length of transmission line l=165km, Load SL=55MVA,Vph=132∠0°kV,cosϕ=0.8 lagging,   The load current…

Q: 25. Find the load impedance Z₁, for the networks of Fig. 18.125 for maximum power to the load, and…

A: Given: A network with current dependent current source,  To find: i) Load impedance for maximum…

Q: For the frequency divider circuit the D-flip-flop is a CD4013 Dual D-Type flip-flop V2 is a square…

A: According to the question, for the frequency divider circuit the D-flip-flop is a CD4013 Dual D-Type…

Q: 6.(20) SGI:V₁=1/0° SD1=1 jQG2 :V2=? SD2-1 Z=j0.5, (a)Find QG2 for |V₂|=1 (b) and V₂ ?(c) If QG2=0,…

A: V1 = 1∠0°SD2 = PD2 + j1SG2 = 0+j1Z= j0.5 = 0.5 ∠90°

Q: the folowing are the symmetrical component of phase current. positive sequence component =10 cis…

A: In this question positive sequence component of phase B current is given....We have to find out…

Q: Calculate the Laplace Transform of x(t)=3 u(t) + e -²t u(t) + e 4t u(-t). Draw the Region of…

A:

Q: A sine wave has a maximum value of 10 V. Its value at 450 is 450 V Q 14.14 VO 7.07 V 4.5 VD

A: A sine wave has a maximum value of 10V with an angle of 45o

Q: 1. For this source voltage, what is the amplitude ? What is the peak to peak voltage V? Vpp = = 2.…

A:

Q: Use graphical convolution to find the output y(t) = x(t) h(t) for the signal x(t) in Figure 1(A) and…

A: Given Data: A system with, Input signal =xt Impulse signal =ht To Find: Output signal

Q: For the circuit shown find the impedance phase angle Z (in degrees) i = 0.02 sin(157t+40) V=2547.4…

A: here we have to find the impedance phase angle

Q: (NEED A NEAT HAND WRITING SOLUTION ONLY OTHERWISE WILL LEAVE A DOWNVOTE)

A: Given: A binary channel,  with  λ=0.5,Px=0=1-p, Px=1=p,  To find: The value of p that achieves the…

Q: Using a d.c. voltmeter and a.c. voltmeter to measure the output filter of a power supply, the obtain…

A: Output voltage measured by using  DC voltmeter VO-dc=25 V. Output voltage measured by using  AC…

Q: A 3-phase star connected system has an earthing resistance of 250. Calculate the equivalent zero…

A: In this question, we have to determine equivalent zero sequence resistance of earthing resistor.…