Question 2An incompressible fluid flows steadily in the entrance region of a circular tubeof radius R = 75 mm. The flow rate is Q = 0.1 m/s. Find the uniform velocity Uat the entrance. The velocity distribution at a section downstream isนumax1-(+)²2Evaluate the maximum velocity at the downstream section. Calculate the pressuredrop that would exist in the channel if viscous friction at the walls could beneglectedL.U1p = 850 kg/m³R

Answered: Image /qna-images/answer/bc7694c0-a5e9-4183-ac0b-8a5f1210efab.jpg

compressible fluid flows steadily in the entrance region of dius R = 75 mm. The flow rate is Q = 0.1 m/s. Find the uni e entrance. The velocity distribution at a section downstrea u น Итах 2 -1-(+)² uate the maximum velocity at the downstream section. Calcu that would exist in the channel if viscous friction at the walls

compressible fluid flows steadily in the entrance region of dius R = 75 mm. The flow rate is Q = 0.1 m/s. Find the uni e entrance. The velocity distribution at a section downstrea u น Итах 2 -1-(+)² uate the maximum velocity at the downstream section. Calcu that would exist in the channel if viscous friction at the walls

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is pumped between two reservoirs in a pipeline with the following characteristics; (d=275mm, L= 50m, = 0.02, minor loss is neglected. The pump performance curve is approximated by the equation: H,=21.5-6507 Where H, is in meters and Q is in m/s. Determine the discharge O and pump head /7 when two pumps in series are used for total static head (4Z=25m).
In a pipe of diameter 300mm the center line velocity and the velocity at a point 100mm from the center, as measured by pitot tube are 2.4 m/s and 2.0 m/s respectively. Assume the flow in the pipe to be turbulent find: 1-Dischrge through the pipe,2-Coefficient of friction, 3 Height of roughness projections.Please do not waste my question solve with correct answers only.
Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70 m, Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the ViScosity), Usef 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation 135 Elevation 140 m Tank (B) Tievation 100m Tank LA) Jund: Elevitions in Write the answer for any numbers after the declmal
QI A stream line of water out from orifice at y=0.6 from the bottom of a big tank and open the atmospheric to fall a water of distance x=1.5m from the wall of tank. The area of the orifice H=650mm2 and the discharge equal 0.117m3/min when the height of water surface is H=1.5m from the axial of orifice. Calculate the coefficient of velocity, contraction discharge? 1 Add file
The head of water at the Inlet of a pipe of length 1500 m and diameter 400 mm is 50 m. A nozzle of diameter 80 mm at the outlet, is fitted to the pipe. Find the velocity of water at the outlet of the nozzle if f=0.01 for the pipe.
out Water flows steadily in a two- duct dimensional bend. The incoming velocity to the bend is parabolic with maximum velocity equal to 9 ft/s. The inclination of the bend is a = = 40°. 2h V. The width of the duct is constant тах (2h = 30 inches). After the bend, the velocity is uniform and equal to Vout- Compute and sketch the force required to keep the bend in place.
Fresh water at 20°C flows from reservoir A to reservoir B as indicated. Calculate the flow rate by a) applying Bernoulli and solving iteratively for flow rate by successive calculation of flow rate and friction factor; and b) making use of the Hardy-Cross method A L = 1000 m d = 100 mm ε = 0.15 mm Pump B 20 m
SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m2/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). HI 300 m H2 datum A = SN/1000 L = 100 x SN (m) D 0.3 m Please solve these question my sn number 31
A pipe of diameter 400 mm carries water at a velocity of 20 m/s .The pressure ta point A is 300000 N/m2 and at point B is 200000 N/m2 , while the datum head at A and B are 20 m and 25 m respectively . Find the loss of head ( HL ) between A and B A- 4.5 m B- 5.19 m C- 6.2 m D- 5.6 m E- 7.1 m
oil flows through a pipe as shown. The coefficient of discharge for the orifice in the pipe is 0.63 What is the discharge of oil in the pipe in l/s D = 250mm , sg =0.91 , 180 mm diameter sharp edge orifice , reading 350mm
Find the cross sectional area Discahrge=20 m3/s Velocity of flow=2 m/s
The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.