Consider a solenoid with a diameter 0.04 m, length 7.6 m, 55 turns, and total resistance 0.6 Ω. The solenoid is connected to a DC source so that a constant potential difference 9.7 V is created at the solenoid’s ends. Find the absolute value of the heat energy dissipated by the solenoid after it is disconnected from the DC source. Use the free space permeability μ0 = 4 π ×10−7 H/m = 1.257×10−6 H/m.

Consider a solenoid with a diameter 0.04 m, length 7.6 m, 55 turns, and total resistance 0.6 Ω. The solenoid is connected to a DC source so that a constant potential difference 9.7 V is created at the solenoid’s ends. Find the absolute value of the heat energy dissipated by the solenoid after it is disconnected from the DC source. Use the free space permeability μ0 = 4 π ×10−7 H/m = 1.257×10−6 H/m.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter23: Faraday’s Law And Inductance

Section: Chapter Questions

Problem 12OQ

See similar textbooks

Similar questions

A 9ohm resistor is connected to a solenoid and a power source of 10V. The solenoid has a radius of 15cm, 200 loops, and a length of 2cm. If we assume the circuit starts with no current, what is the stored energy in solenoid after 0.5 seconds?
Two resistanceless rails rest 42 cm apart on a 6.6o ramp. They are joined at the bottom by a 0.68 Ω resistor. At the top, a copper bar of mass 0.034 kg (ignore its resistance) is laid across the rails. The whole apparatus is immersed in a vertical 0.35 T field. What is the terminal (steady) velocity of the bar as it slides frictionlessly down the rails?
A solenoid consists of 4200 turns of copper wire. The wire has a diameter of 0.200 mm. The solenoidhas a diameter of 1.00 cm. When the solenoid is connected to a 12.0 V battery, we observe that thecurrent increases over time and is 155 mA after 1.50 milliseconds have passed. Assume that the internalresistance of the battery and connecting wires is negligible. (Hint: the solenoid is acting as both the Rand L in an RL circuit).a) What is the length of wire needed to form the solenoid? ________________________b) What is the inductance of the solenoid? ________________________c) What is the length of the solenoid? ________________________d) What will be the current after three time constants have elapsed?
There is a solenoid with an inductance of 0.285 mH, a length of 36 cm, and a cross-sectional area of 6×10−4 m2. Suppose at a specific time the emf is 12.5 mV, find the rate of change (Ampere per second) of the current at that time. Find the number of turns of the solenoid. Round your answer in one decimal place.
A 25-turn ideal solenoid has an inductance of (4.19x10^-3) H. To generate an EMF of (1.5x10^0) V what should be the rate of change of the current? Express your result as the magnitude in A/s.
3. A solenoid has radius 5.80 mm, length 11.0 cm, 5000 turns, and is placed with its axis of symmetryalong the x-axis, through the origin. A vector normal to the opening of the solenoid points to the right.We measure the resistance of the solenoid to be 14.0 Ω. The solenoid is in a region where thetemperature is 49.0°C and initially, there is an external magnetic field of 0.30 T in the +x direction.Then the magnetic field is turned off and drops to 0 T over 50.0 milliseconds.a. What is the magnitude of the average induced emf during the 50.0 milliseconds while the magneticfield magnitude decreases to 0?________________________b. What is the direction of the induced current, as viewed from the right? Answer clockwise,counterclockwise, or zero and show work or explain in words.________________________c. What is the magnitude of the induced current? ________________________d. What is the magnitude and direction of the induced magnetic field?
A circular loop conductor lying in the z = 0 plane has a radius of 0.10 m and a resistance of 10 Ω. Given B = 0.2 sin103tz (T), determine the current.
suppose a conducting rod with length of 25cm is pulled along the a rotated U-shaped conductor (assume that resistance is negligible), the magentic field has a constant value of 37.2 mT and the constant velocity at which the rod is pulled is 5.5m/s. identify the minimum rate of energy input to the system to keep the rod moving at constant velocity if it has a resistance of 7ohms
A resistor R is connected between two parallel conducting rails separated by 30 cm, as shown in the diagram. A conducting bar maintains electric contact with the rails as it moves relative to them with constant velocity from x = 20 cm to x = 48 cm in 0.6 seconds. A uniform 0.8 T field points into the page. Calculate the induced electric potential difference between the two ends of the bar.
There are 163 windings around a cylinder made of a non-magnetic material. The cylinder has a radius r 4.1 cm and a length L 7 m. The resistance of a sufficiently long cylinder (r << L) is R= 22. The applied voltage is E, = 5 V at the initial moment (t = 0). At the time t = 8s what is the value of the voltage E, in units of mega-volts, that must be applied to the ends of the solenoid, in order for the current to increase directly proportional with time t? (Take 4o = 4 x 10 7T- m/A and r= 3.14.) O 3.18 O 18.44 O 9.54 O 6.36 14.31
You want to make a solenoid of radius r and length l out of a piece of copper wire of resistance R, length L, and diameter D, that you already have, and power it with a battery of voltage V that you also already have. The solenoid must be wrapped N times around a cylinder without overlapping turns. What is B (an equation) inside the solenoid going to be based on V, L, D, N (turns), R, r, l, and any other parameters - geometric or otherwise that you need?
A solenoid has a radius of 3.5 cm, 160 turns and a length of 1.2 m. Take the solenoid to have negligible (zero) resistance. The terminals of the solenoid are connected across a 15 Ω resistor at time zero and the circuit is given an initial current of 55 mA. a) How long will it take for the current to drop to 12mA? b) At time zero, just after the current in the circuit is initiated, what is the energy stored in the solenoid and what is the voltage across the solenoid?