answer all Both M1 and M2Consider the circuit shown below. Voltage VB is a constant source.are biased in the active region. Small-signal device transconductances are gmı = 1 mU andgm2 = 0.5 mU. Assume r.1 = 0 and ro2 = ∞ if not specified.a. Find voltage gain Ap1 = vo1/Vin-b. Find voltage gain Ay2 = vo2/vin-c. Find voltage gain Ap3 = vo3/Vin-d. Find output resistance looking into the drain of M1, Ro1: Assume ro1 = 20 knand ro2 = o.%3D%3DVDD10 k2Vo1-Ro1Vin H M,Vo2Vo3R210 k2

Answered: Image /qna-images/answer/67f167b7-06d7-4b4f-bbb4-190903270d30.jpg

Consider the circuit shown below. Voltage VB is a constant source. are biased in the active region. Small-signal device transconductances are gm1 = 1 mU and 9m2 = 0.5 mU. Assume ro1 = 0 and ro2 = 0 if not specified. a. Find voltage gain Ap1 = vo1/Vin- b. Find voltage gain Ap2 = voz/Vin- c. Find voltage gain Ap3 = Vo3/Vin- d. Find output resistance looking into the drain of M1, Ro1. Assume ro1 = 20 kn Both M1 and M2 %3D %3D and ro2 = 00. VDD 10 k2 FR01 VinHE M, 02 Vo3

Consider the circuit shown below. Voltage VB is a constant source. are biased in the active region. Small-signal device transconductances are gm1 = 1 mU and 9m2 = 0.5 mU. Assume ro1 = 0 and ro2 = 0 if not specified. a. Find voltage gain Ap1 = vo1/Vin- b. Find voltage gain Ap2 = voz/Vin- c. Find voltage gain Ap3 = Vo3/Vin- d. Find output resistance looking into the drain of M1, Ro1. Assume ro1 = 20 kn Both M1 and M2 %3D %3D and ro2 = 00. VDD 10 k2 FR01 VinHE M, 02 Vo3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current.
The Pinch off voltage for N-Channel JFET is -3V, maximum saturated drain current 8mA and the value of VGS is -1.5 V. Calculate drain current, a. 4 mA b. 2.5 mA c. 2 mA d. 18 mA
An N-channel JFET has IDSS = 12 mA and a transconductance of 4mA/V when VGS = 0V.a. Find the pinch-off voltage VP b. Fid the drain current when VGS = -2V.
For the circuit given in figure below draw the collector characteristic curves for Ip= 50, 150 and 250 micro amperes on the same graph Re 220 A - Vec 10 V R 10 k Boc= 200 OV-5 V
A fixed bias n-channel JFET with Vdd= 12V, Rd= 1.2k ohms. Idss=12mA and Vp=-4V. Determine Vs. a.0 V b.None of these c.4.35V d.6.7V
10 k2, RE = R, = 150 2, r'e = 50 2, and Bac = 50. The For a common-emitter anmplifier, R value of the voltage gain is +Vcc Rc C3 R oVout REI R2 RE2 Select one: a. 67 b. 100 C. 50 d. 28.5
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. the direction of conventional current flow O c. that it is a P-channel MOSFET O d. the direction of electrons
How do we know that with amplification with emitter degenerate resistor amplifier both M1 and M2 are in the saturation region?
What is the collector current for a C-E configurationwith a beta of 100 and a base current  of 30 uA?A. 30 A  B. 0.3 A  C. 3mA  D. 3MA
Questiona. In an experiment the voltage required for the device is 9V dc but unfortunately the transformer available is of 220-6 Vdc. Design a circuit which can power the device (use only methods that we have studied excluding Zener diode)b. Explain the behavior of the following circuits if the input signal is triangular wave of peak voltage 5V and the biasing battery of 3V
2. Draw the output waveform for the zener limiting circuit. Show your analysis. ANS. Will limit the voltage at 6.9 V; and -15.7 V 1k0 20V 6.2v Vs 15 V -20v
EHide bla This course Determine Vx and the mode of operation of the PNP transistor shown in the figure below. Assume Is = 2.5x106 A,B- 50, VA =, and Rc = 0.1 KO. Vec 2 V EX 1.2 V- Re幸 Select one: O a.1.153 V. Active Mode O60577V. Active Mode Oc 023 V. Active Mode d. None of these Oe 2306 V Saturation Mode For the circuit shewn in the figure below. assume l = 3 107A V= 26mv. B= 100, and V = The value of r-5