Consider the ideal vapor compression cycle operating between 1.4 bar and 9bar using R-125 as the refrigerant, which removes heat from a cold space at a rate of 100kW. If the evaporator outlet was suddenly superheated by 2℃ above saturation, what will be the resulting effect on the cycle? a.Refrigerant flowrate will decrease, Condenser duty will decreaseb.Refrigerant flowrate will increase, Condenser duty will decreasec.Refrigerant flowrate will increase, Condenser duty will increased.Refrigerant flowrate will decrease, Condenser duty will increase

Answered: Image /qna-images/answer/0d8fa3e0-bb1e-4739-81ff-bbaf67d819b2.jpg

Consider the ideal vapor compression cycle operating between 1.4 bar and 9bar using R-125 as the refrigerant, which removes heat from a cold space at a rate of 100kW. If the evaporator outlet was suddenly superheated by 2℃ above saturation, what will be the resulting effect on the cycle?

Consider the ideal vapor compression cycle operating between 1.4 bar and 9bar using R-125 as the refrigerant, which removes heat from a cold space at a rate of 100kW. If the evaporator outlet was suddenly superheated by 2℃ above saturation, what will be the resulting effect on the cycle?

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter22: Condensers

Section: Chapter Questions

Problem 7RQ: When a standard-efficiency air-cooled condenser is used, the condensing refrigerant will normally be...

See similar textbooks

Related questions

Q: Sketch a commercial type outdoor air-cooled condenser. Discuss the heat transfer mechanism in the…

A: The sketch of the commercial air cooled condenser along with its working are as follows:

Q: A horseshoe player releases the horseshoe at A with an initial speed vo- 36 ft/sec. Determine the…

A: Given: Initial velocity→Vo=36 ft/sec Initial height at point A→yA=3.8 ft For upper strike at…

Q: Part a) Reactions The vertical reaction force at support A can be calculated as The vertical…

Q: Part A As shown, a force vector F with a magnitude of c = 26.0 lb is applied at point A and is…

A: As the figure for part 2 is not given so solved part 1. Given-Information:- a = 9.50 ftb = 3 ftc =…

Q: stress 6 Q/Interpret the following drawing soft plastic fiber hard plastic elastomer strain (8)

Q: A steel cantilever beam, of length L=1 m, has a hollow rectangular cross-section, see Figure Q3. The…

Q: A reheat cycle with two stages of reheating is executed with steam expanding initially from 200 bar…

A: Initial pressure of steam: 200 bar (20 Mpaa) Initial temperature of steam: 540 degrees Celsius…

Q: b) Calculate support reactions in A and B, following the defined sign convection. Reaction forces at…

Q: Why were some fuels called unleaded? I. Lead used to be added to diesel to improve its octane rating…

A: This question is based on the concept of fuel.

Q: Sea 0.92 and 1.025, respectively. If a 25-cm-high portion of the ice block extends above the surface…

Q: A Stirling engine involves: (1) isothermal heat addition → (2) isochoric heat removal → (3)…

Q: Discuss why the petrol engine is irreversible in terms of entropy and work lost due to the…

A: A petrol engine is an example of a heat engine, which is a device that converts thermal energy into…

Q: A wooden beam is loaded by a concentrated load P=1000N and supported by boundary conditions shown in…

A: GivenP=1000N LAB=1600mmLBC=3400,B0=10mm,B1=20mmH=230mmh0=150mmh1=40mm

Q: (A): Derive the differential equation governing the buckling of the column shown in figure knowing…

A: Given: Loading conditions on a column Required: Differential equation and first buckling load

Q: At the bottom A of the vertical inside loop, the magnitude of the total acceleration of the airplane…

Q: Given P1 = 60 lbs and P2 = 150 lbs. Determine the resultant of the two forces. Determine the…

Q: A long copper tube (O.D.=0.5 m and I.D.=0.45 m) is centered in a concrete block (square…

Q: 1. Find the curl of the following vector fields a) V= = (3xz², -yz, x + 2z)

A: Given V=(3xz2, -yz, x+2z)

Q: The 10-kg block shown in the figure below rests on the smooth incline. If the spring is originally…

A: Given data: Mass of the block = m = 10 kg Angle of inclination of plane = 30° Distance travelled = s…

Q: Describe the operating principle of a Karman Vortex air flow meter used in some engine management…

A: A Karman vortex air flow meter (KVAFM) uses the principle of vortex shedding to measure the flow…

Q: Determine the thermal efficiency for an ideal Otto cycle with a compression ratio of 6.9, with…

Q: Stress (MPa) Graph 1 - Stress/Strain plot 400 320 300 200 100 0 (a) 51.472kN (b) 205.89kN (c) 25735N…

Q: At the proportional limit, a 31 mm wide by 14 mm thick bar elongates 2.1 mm under an axial load of…

Q: Describe the manipulator (joints, degrees of freedom, sketch the end effector workspace).

A: In the given figure there are three links in the mechanism, in which one link is a fix link and…

Q: In an ideal spark ignition engine, the combustion step is modeled as which process? a.Isochoric…

Q: Compute the total heat gain load from all the sources into the lunchroom, if the lunchroom is…

A: Given: Wall facing SE 20*15, U = 0.3 Btu/hr.ft2.F Roof, U = 0.4 Btu/hr.ft2.F Outside conditions,…

Q: Relationship between Specific Gravity and Head Pressure of the fluid

A: Introduction Specific gravity, sometimes referred to as relative density, is a measurement of a…

Q: (g) A tanker with a mass of 80x10' metric tons is towed by a tug as shown in Fig. 1(g). A constant…

Q: O Determine the 2nd moment of area of the I-beam cross-section with respect to z-axis in Figure (b)…

A: Given P = 2000N LAB =2100 mm LBC =2900 mmBo= 10 mm, B1 = 20 mm H = 240 mm h0= 200 mm h1= 20 mm

Q: A pipe having a diameter of 30 cm is exposed to an atmospheric pressure of 70 cm of mercury, while…

A: In this issue, we will compute the maximum permitted internal pressure in the pipe while measuring…

Q: P4. The open loop transfer function of a unity feedback system is given by K G (s) = s(as+1) (Bs+1)…

Q: The turning-moment diagram for one cycle of a multi-cylinder engine shows fluctuations in energy…

Q: The wooden beam (E = 10 GPa) is loaded as shown. Using the Method of Superposition, find the slope…

A: Given data: P=4 KN =4*103 NThe length L=6 mdistance from A to C ,a=1.5 mdistance from B to…

Q: Which of the following is not an assumption for the ideal vapor compression process? a.Isobaric…

Q: QUESTION 9 A liquid cooled heat sink for a smartphone is sketched in Figure Q9. It uses water of…

A: Density ρ= 997 kg/m kinematic viscosity v= 1.19 x 10-6 m2s-1 No of tubes = 5 diameter Dh =5 mm…

Q: A shaft with 3 meters span between two bearings carries three masses of 10 kg, 20 kg and 15 acting…

A: Given: Length of the shaft→L=3 m mass→m1=10 Kg; →m2=20 Kg; →m3=15 Kg Length of the arms →L1=45…

Q: QUESTION 15 The slider crank mechanism in Figure Q15 consists of a piston connected by a rod to a…

Q: * A 200 MW Steam Power Plant operates on a simple Rankine Cycle assuming non-ideal isentoric…

Q: QUESTION 5 1. A table has four tubular legs of length 0.75 m. The thin-walled tubes have an inner…

A: Given data L=0.75m, r=4.5cm and t= 0.28cm The youngs modulus = 0.8GPa Find the maximum mass the…

Q: What are the advantages of using cascade refrigeration? I.Higher required pressure differences for…

A: This question is based on the concept of the Cascade refrigeration system.

Q: Confine with 1 lb of wet steam at 500 F and with an enthalpy of 800 Btu in a rigid container. Heat…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: from an aluminum alloy that has a plane strain fracture toughness of 45 MPa m and a yield strength…

A: Given data Fracture toughness = 45MPa√m The yield strength = 500MPa maximum critical internal crack…

Q: A gas with specific volume v₁ = 1 m³/Kg and pressure p₁=1bar in a closed system undergoes a…

Q: Discuss why the petrol engine is irreversible in terms of entropy and work lost due to the…

A: A petrol engine is an example of a heat engine, which is a device that converts thermal energy into…

Q: The Fatigue behaviour of initially crack free aluminium 6061 is shown in Figure Q12. A component…

A: Given: For the life of →N1=100000 cycles of loading, the stress amplitude is: →σ1=150 MPa And for…

Q: f one mole of air/fuel mixture (rigid diatomic gas) is initially at 20◦C, is compressed and expanded…

A: The initial temperature is Ti=20°C=293 K The compression ratio is rk=7 The number of mole of gas is…

Q: WHAT ARE THE DIFFERENCE BETWEEN THE TURBO ROCKET ENGINE AND TURBO RAMJET ENGINE in airplane

A: The ramjet engine are different from turbojet rocket engine. The RAMJET ENGINE can not operate at…

Q: The 2.00-kg slender rod shown is hanging in a vertical position and is pin-supported at point A. The…

Q: STRESS STRAIN Typical for thermosets Typical for thermoplastics Q/Interpret the following drawing

A: Introduction Thermoplastic and thermosetting plastics are both polymers, but they react to heat (as…

Q: An intermediate fuel oil (?=996 ??/?3) stands 12 m deep in a storage tank whose top is open to the…

A: Given data: ● The density of the oil: ρ = 996 kg/m3 ● The height of the oil: h = 12 n ● Take…

Question

a.Refrigerant flowrate will decrease, Condenser duty will decrease

b.Refrigerant flowrate will increase, Condenser duty will decrease

c.Refrigerant flowrate will increase, Condenser duty will increase

d.Refrigerant flowrate will decrease, Condenser duty will increase

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given data

VIEW

Final Solution

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.