Consider the inverting amplifier shown in Figure Q1c. Initially R₁=10 ks, R₂=1 MS2 and R3 is a short circuit (02). R₁ R₂ w R3 A • Vo Figure Qlc (i) If the op-amp has an input bias current of 100 nA and an input offset current of 10 nA, calculate the output voltage. [2] (ii) Evaluate the required value of R3 to cancel the effect of bias current at the output. [2] (ii) Calculate the new value of Vo. [2] Explain the need for decoupling capacitors and the importance of their placement. [4]

Consider the inverting amplifier shown in Figure Q1c. Initially R₁=10 ks, R₂=1 MS2 and R3 is a short circuit (02). R₁ R₂ w R3 A • Vo Figure Qlc (i) If the op-amp has an input bias current of 100 nA and an input offset current of 10 nA, calculate the output voltage. [2] (ii) Evaluate the required value of R3 to cancel the effect of bias current at the output. [2] (ii) Calculate the new value of Vo. [2] Explain the need for decoupling capacitors and the importance of their placement. [4]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
1- Mention any two non linear applications of op- amp. 2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
The two input terminals of an op-amp are connected to voltage signals of strength 745µV and 740µV repectively. The gain of the op-amp in common mode is 50 and CMMR is 8&IB. Calculate the output voltage and % of error due to common mode.
One way to measure the slew-rate limitation of an op amp is to apply a sine wave (or square wave) as the input to an amplifier and then increase the frequency until the output waveform becomes triangular. Suppose that a 1-MHz input signal produces a triangular output waveform having a peak-to-peak amplitude of 4 V. Determine the slew rate of the op amp.
If the ideal design for op-Amp circuit generate 200 mV at the output, Then practically with 26 mV offset voltage the output voltage of the circuit will be equal to .. . mV
An inverting op amp has Rf= 600kohm and R1= 6kohm. Determine the op amp circuit voltage gain, input resistance and output resistance. Also Determine the output voltage and input current if the input voltage is 0.1 V. Assume op amp to be ideal one.
Consider the following circuit using diode and Op-Amp. Assume ideal Op-Amp with output saturation at +-13V. Assume diode forward drop is 0.7V. a. Find Vo and VA when Vin = 1V and 3V. b. Find V, and VA when Vin = -1V and -3V. R Vin R VA ovo ER₂
The two input terminals of an op-amp are connected to voltage signals of strength 754µV and 740µV repectively. The gain of the op-amp in differential mode is 50 and CMMR is 80 dB. Calculate the output voltage and % of error due to common mode.
(c) (d) Figure Figure Q1b shows an Op-amp with a bias current compensating resistor (Rp). R₁ V₂. Vp IB. R₂ W A • V₂ Figure Olb (i) Derive an expression for V. to quantify the effect of bias currents IB+ and IB-. [3] (ii) Explain how you would choose a value for Rp to reduce the output error due to the bias currents, IB+ and IB.. [3] Referring to an op-amp define what is meant by common-mode rejection ratio (CMRR) and explain the effect a finite CMRR would have on high-precision applications. [4] Page 2 of 7 Continued overleaf
A differential op-amp circuit as shown below is used to implement a given linear voltage measuring functionV = f(V,). ouf Provide answers to questions 19 – 22. ww V. V; W R out R2 Ground
Draw an op amp symbol including sources to account for offset voltage, offset current, and bias current. What is the principal effect of these sources in an amplifier circuit?