Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?

Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Similar questions

Draw the FBD for the bar described in Prob. 5.1 if the bar is homogeneous of mass 50 kg. Count the unknowns.
The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
Can the uniform bar of weight W remain at rest in the position shown?
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The drum shown in Fig. (a) has a radius of gyration of 30 cm and weights 1,8 kN. It is supported by means of small hubs which rest in bearings. A weight of 1 kN is attached to one end of a rope, the other end being wrapped around the drum. Neglecting friction in the bearings, determine the acceleration of the weight, the angular acceleration of the drum, and the tension in the rope. 37.5 cm 1.8kN T IkN
The uniform slender rod, witha mass of 9.6 kg and a length ofE = 0.76 m, is fixed to a light vertical shaft at 0. The shaft can rotate freely in the stationary socket on the floor. A constant moment of M 11.8 N m is applied to the shaft, as indicated. What is the magnitude of the angular acceleration (in rad/s) of the rod? The rod moves in a horizontal plane.
The ABCD structure illustrated on the left is used to stop the rotational movement of an inertia wheel attached in O while having a cusion B in contact with the wheel. The static friction coefficient is 0,4 and the cinetic friction coefficient is 0,3. The couple M applied on the inertia wheel is 300N*m. The lineic weight of the ABC membrane is 200N/m. The effort of compression in the hydraulic cylinder CD is 3,50 kN and its weight is negligible. Determine: 0.6 m a) if the inertia wheel turns or not b) the efforts on the ABC part 1 m 30° B 60 mm A M 0.3 m
The shown spool has a mass of 100 kg and radius ofgyration of 0.3 m. For P = 70 N and ms =mk = 0.2 thespool rolls without sliding, calculate the angularacceleration of the spool
A tractor is now drafted in to move the blo ck. The weight of the tractor is equally distributed over all four wheels and it pulls on the blo ck via a rope with tension T. The back wheels have a diameter of 1.6m and the front wheelshave a diameter of 80cm. The tractor motor generates a torque of τ on each of its back wheels that have radii Rb and masses mb. The front wheels of the tractor are smaller than the back wheels and have radii Rf and masses mf. Both sets of wheels can b e treated as uniform solid disks with moment ofinertia I = 1/2mR2. The mass of the tractor body, without the wheels, is M. If the wheels don't slip, show that the tractor can accelerate the block with an acceleration of (see image)
In the given 15.0 meter slab and inclined 10°with the horizontal, the ends are resting on inclines of 30° incline at B and 20° at A, a semi-trailer truck is to pass through it with the wheel loads as shown. How Far (x, meters) shall be 3. the front wheels located before motion impends, the angle of friction is 15° for all areas of contact. Neglect the weight of the slab 15.00 m 24KN 40 KN 32 KN 16 KN 3.6 m 4.0m 20 30
Consider a hollow clay cylinder, which has a moment of inertia 87 kg-m2. The cylinder is free to rotate frictionless-ly, and it starts from rest. It rotate about a fixed axis through its center. Let's assume that we apply a tangential force to the end of the cylinder (the flat face of the shape) with a magnitude which can range from F = 0 to F = 61 N. The force can be applied at any distance from the axis of the cylinder ranging from R=0 to R=4 m from the axis of rotation. (a) Find a pair of values of F and R that cause the disk to complete 2.00 rev in 10.0 s. (b) Is your answer for the previos part unique? How many answers exist?