Consider two discharges of BOD from chemical plants along a river separated by some distance d. a. draw a sketch showing how DO and the rate of rearation varies with distance in comparison to saturated DO levels. b. In a separate sketch, show how Lt varies with downstream distance.

Consider two discharges of BOD from chemical plants along a river separated by some distance d. a. draw a sketch showing how DO and the rate of rearation varies with distance in comparison to saturated DO levels. b. In a separate sketch, show how Lt varies with downstream distance.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Related questions

Q: Consider the catchment area shown in the figure below has three rain gauges as labeled. For the…

A: A method for determining the importance of point rainfall data in terms of area. Perpendicular…

Q: well is sunk through an unconfined aquifer and is pumped at a constant rate. The draw-down in he…

Q: QUESTION#1:- Compute the discharge of a river from the data given in table below. The curent meter…

A: The discharge is given by: Q=A×V Where, A = Cross section area = Width×Depth V = Velocity = n×a+b n…

Q: Problem: Three pipes of different length and diameters connected in series as shown discharges 160…

Q: In a rectangular sprinklers distribution pattern, the displacement F is equal to

A: Sprinklers Sprinkler is a garden device that sprays water onto your grass or plants,. Sprinklers are…

Q: Q2 Figure Q2 shows a cross section of a river at Sg. Melaka treatment plant. Using data in Table Q2,…

A: mid-sectionQ=bi+1-bi-12×Vidi

Q: For a ditch drain shown in the figure below find discharge capacity in cumecs using Elliot's formula…

A: finding discharge via elliot's formula while gradient and cross section of channel given

Q: A three reservoir problem shown in the figure with their corresponding length and diameter.…

A: L1= 1700m L2= 1900m L3= 3500m

Q: Calculation and Results 1- Calculate the Reynolds number for each flow quantity and indicating the…

A: Given flow rate data: Diameter of pipe (D) = 1.8 cm Length of pipe (L) = 87 cm Area of…

Q: 791 cfs 197.75 cfs K = 1 K=4 K = 5 197.75 cfs 395.5 cfs K = 3 K = 2

A: Given :- Coefficient of friction(K) in each pipes K1=1 K2=4 K3=3 K4=4 K5=2 K6=5 n= 2 i.e. the number…

Q: 2) A simple water distribution system is shown in the diagram below. Determine the flowrate (cfs)…

Q: What is the maximum depth of rainfall in inches for 90 min rainfall intensity? Refer to the Table…

A: By doing cumulative for all the rainfall intervals we can find depth of rainfall for 90 min rainfall…

Q: How would we derive a solution for groundwater drawdown due to pumping near a river (i.e. a recharge…

A: Brief concept introduction- Groundwater- It is the water that is stored under the earth's crust.…

Q: A radial system consists of four layers with the following properties: Layer Inner Radius [m] Outer…

A: To determine the average permeability of a given radial system for flow in series. Given, Layer…

Q: A simple reservoir has a linear storage indication curve defined by Q/2 = S /At, where At = 1.0 hr.…

A: Hydrograph: A hydrograph is a plot that depicts the flow rate vs time in a river, channel, or…

Q: Problem 1 Water flows in a rectangular channel of constant width with a flowrate per unit width of q…

Q: Three reservoirs 1, 2, & 3 have elevations 322 m, 306 m, and 272 m respectively. The 3 pipes have…

Q: Flow net under a concrete dam is shown in the following Fig. Q. 3(d). Calculate and plot the water…

A: By knowing the flow net , water distribution varying linearly with maximum at the upstream and…

Q: Following are the data of gauge and discharge collected at a particular section of the river by…

A: Given, stage-discharge data as, Discharge (cms) Gauge reading (m) 20 6.4 40 6.4 76 6.5…

Q: Select the best answer .Show your solution 1. Determine the volume of direct run off in cu m that…

Q: How do you determine the capacity of the reservoir? Explain the process for determining the capacity…

A: Reservoirs are generally constructed on rivers in order to full fill the water demand during…

Q: 1. Water flows through a 75 mm diameter pipe at a velocity of 3 m/sec. Find (a) the volumetric flux…

A: Given data in question Diameter of pipe Velocity of water To find out Volumetric flux Mass flux…

Q: 3) You are assigned to determine the Manning's n coefficient for sagebrush. In eastern Oregon where…

Q: Water flows at a rate of 0.020 m 3/s from reservoir A to reservoir B through three concrete pipes…

Q: What is the maximum depth of rainfall in inches for 90 min rainfall intensity? Refer to the Table…

A: Solution: Intensity of Rainfall is defined as ratio of depth of rainfall to the time. It's denoted…

Q: 2.In a water treatment unit, the flow through a trapezoidal cross-sectional tapping channel, is…

Q: c. Maximum Annual discharge for the Chikasia River near Blackwell, Oklahoma for 1936- 1977 is given…

Q: 1. If the flow out is 200 mm³/sec in figure 1, find K1 and K2 dh = 0.01 mm/sec, dt 2. In figure 2,…

Q: Consider the catchment area shown in the figure below has three rain gauges as labeled. For the…

A: PA = 65 mm PB = 49 mm PC = 81 mm Pmean = ? Draw the lines as per Thiessen polygon method and…

Q: Flow rate was monitored for a week, and the following values were recorded as gal/min: 10.1, 12.2,…

A: Question is related to fluid mechanics.

Q: Obtain relation D=aT for the following hydrologic data using MS EXCEL

A: Given: Accumulated time, T(min) Accumulated depth, D (mm) 15 17 75 29 To obtain:…

Q: Outline the main components of Darcy’s Law and explain to what extent can it provide a useful…

A: In soil mechanics, if the water level is different on opposite sides of the soil, the water tends to…

Q: An engineer wanted to determine Q20 when he designed a bridge for a highway. He collected and…

A: Flood frequency analysis: This analysis is a process used by hydrologists that are used to predict…

Q: Figure for Situation 7 Flow Overflow 375mm Discharge 225mm Soil 150mm 300mm

Q: b. Figure 3.2 is the flow of a channel having a large width, b, under a sluice gate. Assuming…

Q: Two reservoirs are connected by two pipelines as shown in Figure 5.1. The difference in the…

Q: The following figure illustrates the flow net for a proposed structure at the Alaska shore. From the…

A: Given data: H=10, K=6×10-5m/sec from figure, Nf=3, Nd=12 K=6×10-5K=6×10-5×60×60×24=5.18m/day For…

Q: The waterline section of a barge is as shown. A=7 B=7 C=5 D=2 a) Calculate the total area (m2 ) of…

A: Figure is as shown

Q: Problem 2. A Venturi flume with a rectangular cross-section is used to measure the flow rate from a…

A: Given data d1=1 m The expression for area is given as A1=π4d12 Substitute the value in above…

Q: In the table below data for precipitation and runoff both in depths of cm are given for June during…

A: The data given is arranged in ascending order: Runoff Precipitation 0.8 8 1.2 9 2 10 2.5…

Q: Q3) For steady flow in rivers, the discharge measurements are taken during both the rising and…

Q: g (gravitational acceleration), spillage The influence of the road height P (spillway height), using…

A: Variables are Q,H,g,Pso,Taking H,g,P as repeating variables

Q: The table below represents the flow information for a river, follow the flood hydrograph of this…

Q: Question 7 (Parallel pipes) Two reservoirs are connected by two parallel pipelines with diameters of…

Q: B) Water at 20 degrees Celsius flows at a rate of 0.05 m3/s in a D=20cm asphalted cast-iron pipe.…

A: Solution: Q=0.05m3/s D=20cm=0.2m L=1km =1000m Q=VA A= For circular cross-section of pipe A=π(d/2)2…

Q: The following data were observed at the X dam reservoir in April 2020. Find the average groundwater…

Q: 6. When just full, a reservoir has a surface area of 1 km², and this area is approximately constant…

A: A=1 km2O=100 h1.2

Q: The following figure shows a flow network. The permeability is k = 5x10-3 cm / s, solve the…

A: Consider the free body diagram as;

Q: A 40-year annual series of eak river discharges with the mean equal to 15,000 cfs and standard…

A: we know that Gumbel's methodpeak value XT=X+Kσfrequency factor k=yT-ynSnReduced variate…

Concept explainers

Field applications of hydraulic conductivity

Hydraulic conductivity is one of the hydraulic properties of soil defined as a measurement of the ability of a porous medium to permit water movement or fluid flow through it. It is denoted by the letter K. It is influenced by the density and viscosity of the fluid. It is also called permeability. Hydraulic conductivity is defined as the ratio of velocity to the hydraulic gradient. The different methods used to determine the hydraulic conductivity are laboratory methods (constant head permeability tests and falling head tests), in-situ field methods (pumping in and pumping out tests), small scale field tests (infiltration tests and slug tests), and indirect methods such as estimation from grain size, consolidation test data, and horizontal capillary test. The pedotransfer function (PTF) method is a specific empirical estimating approach employed in the soil sciences is also used to determine the hydraulic conductivity of the soil.

Question

Consider two discharges of BOD from chemical plants along a river separated by some
distance d.
a. draw a sketch showing how DO and the rate of rearation varies with distance in
comparison to saturated DO levels.
b. In a separate sketch, show how Lt varies with downstream distance.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Field Applications of Hydraulic Conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

se that 1 of 1 Consider the frame shown in (Figure 1). Suppose that F₁ = 850 N Figure 200 N/m Y Part C FA= Y Part B Submit 60° Determine the magnitude of the reaction at pin A Express your answer to three significant figures and include the appropriate units. Submit PA Value Request Answer A μÁ FB = Value Request Answer Fo= Value Determine the magnitude of the reaction at pin B. Express your answer to three significant figures and include the appropriate units. 2m Units Submit Request Answer Units - 0 < 1 of 1 Determine the magnitude of the reaction at pin C on CB Express your answer to three significant figures and include the appropriate units. Units ? ? 2m ?
Example 6.13 For the following functions in two-dimensional irrotational flow, determine the conjugate functions (a) y = m In r m cos 0 (b)
Which of the following is false regarding factor of safety in the design of structures? a. It considers uncertainties in the material properties. b. A higher factor of safety is preferable in designing safe structures c. It should not be less than 1 to ensure the structure’s safety. d. It considers changes in the loading pattern on the structure. Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
For flow in a pipe with Reynolds number of Re=10^7:
The intensity of the distributed load acting on the beam is w = 3.1 kN/m. (Figure 1) igure A 3 m 30⁰° 4 m B < 1 of 1 Part A Determine the magnitude of reaction at A. Express your answer to three significant figures and include the appropriate units. NA = Part B Submit Request Answer B₂, By = μA Value Submit Determine the x and y components of reaction at B using scalar notation. Express your answers using three significant figures separated by a comma. Provide Feedback VE ΑΣΦ | | Units Request Answer ? vec ? kN
3. Consider the following scenario: A civil engineering stadent measures the resistivity of a particular cytindrical wire for different lengths L by tapping at points the wire from 0.l m to 1 m in steps of 0.1 m The radms of the wire is 0.02 mm. The experiment is carried out under following circumstances: a) The best line has been drawn through the points given below and determine the resistivity of the wire from the slope of the plot between blue marked points. b) Based on the vahue of resistivity you calculated, what is the material wire resistor made of? Make sure everything is in ohms and meters, otherwise your units will not work out correctly in the end! Table 1. Resistivity of Some Common Materials. Material Silver Соррer Gold Aluminum Steel Lead Manganin (Cu. Mn. Ni alloy) Constantan (Cu, Ni alloy) Mercury Nichrome (N. Fe. Cr alloy) Resistivity p ( N-m) 1.59x 10 1.72x10 2.44 10 2.65x10 2x10 22x10 4.4x10 4.9x107 9.6x10 1-10 9. 8 7- 6- 5. 3. 2. 00 0.2 0.4 06 08 Lim)
3. Determine the resultant of the three forces acting on the dam shown in the figure and locate its intersection with the base AB. Required: Resultant and its intersection with the base AB Solution: P-10,000 lb -24,000 f F-6000 tb
Example 2 Two spheres are pressed against each other by an external force. The diameter of the spheres are 20 nm and 30 nm. The elastic constants are Esphere.= Esphere. 2 =150 GPa and Poison ratio are Vsphere-1= Vsphere-2= 0.3. Determine the geometrical factor using DMT model.
Water at flows in the system shown. The density of the water is 1.94 slugs/ft', and the viscosity is 2.359x10 slugs/ft-s. Determine the following. a. Q ignoring minor losses b. Q accounting for minor losses Kt 0.5 10 ft IK,- 10 D= 3 ft L= 1000 ft eps = 0.00164 ft Q = ? Ka= 1.0
Problem 2: Boundary Layers State an example where engineers deliberately modify a surface to create a turbulent boundary layer, and explain why. (25 words) Hint: Review Finnemore and Franzini (2002) §9.7 and the handout "Backspin and Lift." (a) A small (6) R large Laminar Plate Laminar Turbulent de Turbulent TI Plate
Prepare a basin with half filled water and stone.drop a stone into the basin and observe what will happen 1.what happens when you drop the stone2.what causes the ripples to form3.how far does the ripples continue ANSWER 1,2,3
Please solve chapter Analytical Positioning Reactions max 30-45 minutes thank u A beam with bearings A (rolls) and B (joints) is loaded as shown in the figure. Given : The working moment is 96 kNm at B, and the load is evenly distributed to the triangle acting 16KN/m on the high side of the triangle. Question: Calculate the magnitude of the deposition reaction at A and at B in an analytical way, include the units and indicate the direction of the reaction Note : In Image A = rolls B = pin/joints