Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The state diagram is shown below. 000 Y = 1 010 110 Y = 0 101 111 011 100 001 1
Q: QI/ Design a 2-bit randoim counter using T flip flop according to the following sequence! Start End…
A:
Q: Design a gray code counter using T flip-flops based on the following state diagram. (Hint: Use truth…
A:
Q: Design synchronous counter using JK flip flops to count the following binary numbers 0000 ,…
A: We have to design synchronous counter using JK flip flops to count the following binary number:…
Q: By using three JK flip-flops, a continuous counting synchronous counter will be designed in the…
A:
Q: Design the synchronous counter that counts these digits 0 1 2 4 5 6 8 using JK flip-flops
A:
Q: Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The…
A:
Q: Question 2 By using a J-K flip - flop design a binary counter with the following sequence…
A: The counting sequence is 1,0,4,3,6,4,6 Here in counting sequence of 4 , next state comes out to be…
Q: How many flip-flops will be needed when following synthesized? codes ar always @(posedge clk) begin…
A: A flip flop is used to store 1 bit of information to store series of data registers are used. Always…
Q: For a 5421 code up counter designed using JK flip-flops, which of the following statements is false?…
A: BCD CODE-binary code in decimal represent than consider it as don't care. Also, if any invalid BCD…
Q: Design a 3-bit binary counter using T flip-flops and gates which counts in the sequence of…
A:
Q: Which one is true for D flip flop? a) It has 2 inputs 1 output b) It has always the output 1. c)…
A: D flip flop or delay flip flop is used to remove the limitation of SR flip flop. When S=1 , R =1…
Q: a) A 4-bit ripple counter consists of flip-flops, which each have a propagation delay from clock to…
A:
Q: Find the binary assignment table for the following circuit, then re-design it using JK flip flops. S…
A: Given circuit diagram: To find: Binary assignment table for the following circuit and re-design it…
Q: Find the binary assignment table for the following circuit, then re-design it using JK flip flops. R…
A: The binary assignment table shows the present state, next state and output. The present state, if…
Q: Find the binary assignment table for the following circuit, then re-design it using JK flip flops.
A:
Q: 4- Design synchronous counter for sequence: 0 1 → 3 → 4 → 5 -→ 7→ 0, using T flip-flop.
A: Given a counter sequence 0 - 1 - 3 - 4 - 5 -7 - 0 Then the expression for Tc will be
Q: DESIGN THE SYNCHRONOUS COUNTER WITH THE FOLLOWING STATE TRANSITION DIAGRAM. USE J-K FLIP FLOP IN THE…
A:
Q: Using JK flip-flops:1. Design a counter with the following repeated binary sequence: 0,1, 2, 3, 4,…
A: The counter can be designed with the help of three JK flipflop. The state transition table should be…
Q: Determine the Q output for the J-K flip-flop, given .2 tha innuts shown. CLK CLK K K
A: The timing diagram as given in the question gives the states of J, K and the Clock (CLK). Now since…
Q: repeatedly Stepper generate predefined binary data, You can use a flip-flop that is assembled into a…
A:
Q: Q5 A Moore machine is to detect three or more consecutive zeros on an input bitstream using D flip…
A: The solution is given below
Q: For a 5421 code up counter designed using JK flip-flops, which of the following statements is false?…
A: BCD CODE-binary code in decimal represent than consider it as don't care. Also if any invalid BCD…
Q: Using T flip flops, design a 3 bit counter which counts in the sequence: 111, 110, 101, 100, 011,…
A: We need to design 3 bit counter which counts in the sequence:…
Q: Design of a digital electronic circuit that produces 4 bits of binary numbers sequentially and…
A:
Q: Design Asynchronous counter using negative edge J-K flip flop to count the following states ( 10→…
A: Here the properties of JK flipflop has been used to solve it. Here number of bits or flipflop needed…
Q: 2- Design Asynchronous counter using positive edge J-K flip flop to count the following states…
A: According to the desirable counter sequence, the Truth table will be Output waveform w.r.t clock…
Q: A 4-bit ripple counter consists of flip-flops, which each having a propagation delay from clock to Q…
A:
Q: What is the use of Pin 7, 9 (Set 2 and Set 1) and Pin 4,12 (Reset 1 and 2) How to connect these…
A: According to the question, we need to explain the work of the pin number (7, 9) & (4, 12) of the…
Q: 3. Construct the Finite State Machine [FSM] using JK flip flop for the following state diagram (Note…
A:
Q: DESIGN THE SYNCHRONOUS COUNTER WITH THE FOLLOWING STATE TRANSITION DIAGRAM. USE J-K FLIP FLOP IN THE…
A:
Q: 2. Determine the Q waveform for the flip-flop as seen in the figure below. Assume that Q = 0…
A: In this question, We need to draw the output waveform of the JK filp flop. If initially Qn = 0
Q: Design the circuit from the state diagram below using RS flip-flop. Hint: Do the state table first.…
A: I have explained the answer below steps
Q: 4. Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t +…
A: Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t+1) =…
Q: Find the binary assignment table for the following circuit, then re-design it using JK flip flops.…
A: For the given logical circuit, binary assignment table is drawn, which shows that Output is set only…
Q: Question 2 By using a J-K flip - flop design a binary counter with the following sequence 1,0,…
A: The counting Sequence is 1,0,4,3,6,4,6 Here in counting sequence of 4 , next state comes out to be…
Q: Design a synchronous counter that operates according to ate diagram given below. Your design should…
A:
Q: Design a three bit counter which counts in the following sequence: 001, 010, 101, 110, 111, 011,…
A: Draw the state diagram table for the JK flip-flop. Present State Next State Inputs Q(t)…
Q: Design a counter that count the sequence 0,1,3,4,7,0,.. by using T- flip flop. Analyze the unused…
A: SEQUENTIAL LOGIC CIRCUITS: Sequential Logic circuits, unlike Combinational Logic circuits, have some…
Q: 4. Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t +…
A: Using the given equation design the equivalent D Flip-flop, state table, and state diagram A(t+1) =…
Q: Draw the circuit of asynchronous reset D flip flop. Write verilog code for T flip flop.
A: Latch is asynchronous device. It check input and change output correspondingly Flip flop is a latch…
Q: / Design Synchronous counter using J-K flip flop to implement the following counting statements:…
A:
Q: In the asynchronous counter, If increases flip-flop number . .?....... increases. 33 - O A CLK pus e…
A: The system or group of flip flops in which the clock is not applied simultaneously and the output of…
Q: FFI FF2 FF3 Clock to Q delay (ns) 4 2. Set up time (ns) T. Hold time (ns) followinc the…
A: Flip flop is a latch with additional control input (clock or enable ). A flip flop is used to store…
Q: Q. 5 Design a synchronous counter that will count according to the following sequence: 1 - 2 - 6 - 4…
A:
Q: The state diagram shown: 1. Write the characteristic equations 2. Design use T Flip Flops Draw ASM…
A: Given: Let input be X Y Let be output be A Z
Q: Design synchronous counters that go through each of the following sequences f. 1 3 5 7 6 4 2 0 and…
A: A synchronized counter is one in which all of the flip flops are timed at the same time using the…
Q: Find the binary assignment table for the following circuit, then re-design it using JK flip flops. S…
A: For the given logical circuit, binary assignment table is drawn, which shows that Output is set only…
Q: Q.5 Design a synchronous counter that will count according to the following sequence: 0-1-3-7 and…
A:
Q: H.W Q/ Show how a synchronous BCD decade counter with J-K flip-flops can be implemented having a…
A:
Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops.
The state diagram is shown below.
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 3 images
- Design a 6-bit counter with control input using flip-flops. Every hour pulseIt should be a design that will increase or decrease by 4 when it arrives. Control input increment orwill determine the decrease. Increasing when control input is 0, decreasing when 1should be designed.Design a 3-bit synchronous counter, which counts in the sequence: 001, 011, 010, 110, 111, 101, 100 (repeat) 001, ... Draw the schematic of the design with three flip-flops and combinational logics.4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially Low. HIGH CLK- CLR nnnnnnn CLK PR CLR
- a. Construct a synchronous 3-bit Up/Down counter with irregular sequence by using J-K flip-flops. The state diagram is shown below. Y = 1 00 010 110 Y =0 101 111 0, 011 100 001 b. Construct an asynchronous counter with a modulus of eleven by using J-K flip-flops. The counter should follow the straight binary sequence from 0000 through 1011. c. The counters are used in cascading in order to achieve the higher modulus operation. A certain application requires an overall modulus of 39,000 which can be achieved by placing the counters in cascading. You are requested to design a circuit for the said purpose by using 74HC161.Use D flip-flops to design a mod-16 binary down counter, whose counting sequence is 1111->1110->1101->1100->1011-> … ->0000->1111…. Derive the logic expressions for the D inputs of the flip-flops and draw the circuit diagram.Design the 4-bit Johnson Counter using D flip-flop as shown in the figure in the VHDL code. 4 Bit Johnson Counter using D FlipFlop él 9 CLOCK RESET FDC CUR 3 FDC FDC FDC
- 4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially LOW. PR HIGH CLK- K CLR CLK- PR CLRDesign a 4-bit ring counter using D flip-flop and draw the logic diagram of a 4-bit ring counter State Table: 4-bit ring counter (Shift Right) Present Next State State ABCA 001 B 0 10Show how an asynchronous counter with J-K flip-flops can be implemented having a modulus of eleven with a straight binary sequence from 0000 through 1010 . Draw the diagram.(need only handwritten solution .otherwise downvote.)
- Design a 3-bit up/down counter using positive edge-triggered T flip-flops. Provide a respective timing diagram to justify the design. Show all the relevant working (state table, state diagram, K-maps, state equations, and final circuit diagram). An up/down counter has two inputs say x, y, and a clock signal. The output should increase by 1 if x = 1 and y = 0 on each rising edge of clock and decrease when x = 0 and y = 1 on each rising edge of clock. When x = y, the output should neither increase nor decrease on each rising edge of clock.question from DIGITAL LOGIC DESIGN book Design a synchronous BCD Counter based on the following conditions. Design the Down counter with JK-Flip Flops by initializing the counter with 3 and count next five states. The counter should cycle back after counting five states. Perform all necessary designing stepsDesign a 4-bit counter C( represented by C3C₂C₁C₁)which can count the specified sequence as following: 0000011010010010 ➜ 11000000. The counter will use the falling edge of the clock (denoted by Clk) and have a separate reset pin (R) which will reset the counter to 0000 when it is low (e.g. = 0). Please use D type Flip-flops. Write down the state diagram, and state table; Use K-map to simplify the input equations; Write down the simplified input equations and draw a neat circuit diagram. (Hint: use don't care for unused states)