(d) Design an underground rectangular tunnel drift, in a massive granitic rock with a UCS over 100 MPa, of width: 3.1 m, height: 4.1 m, and length 10 m, using an initial Burn-Cut method to create an extra surface for the next underground Bench-Blasting operation, where the idea is roughly illustrated in Figure A3-Q2. : VIII VII VIII VIII IV . IV VII IV IV Development leading Salad care andy VII Brech Blast hader 2 VII . VIII VII VII VII VIII Firing sequence for tunnel numerical order 1 Dorsegment healing Seldcre body Burn cut (after ICI) Arabic numerals: short delay periods Roasan nunerals: half-second periods xy-section view Derech Eros Batt holes Bench blasting methods (yz section view) Figure A3-Q2. Idea of new free surface creation in underground drifts and tunnels

(d) Design an underground rectangular tunnel drift, in a massive granitic rock with a UCS over 100 MPa, of width: 3.1 m, height: 4.1 m, and length 10 m, using an initial Burn-Cut method to create an extra surface for the next underground Bench-Blasting operation, where the idea is roughly illustrated in Figure A3-Q2. : VIII VII VIII VIII IV . IV VII IV IV Development leading Salad care andy VII Brech Blast hader 2 VII . VIII VII VII VII VIII Firing sequence for tunnel numerical order 1 Dorsegment healing Seldcre body Burn cut (after ICI) Arabic numerals: short delay periods Roasan nunerals: half-second periods xy-section view Derech Eros Batt holes Bench blasting methods (yz section view) Figure A3-Q2. Idea of new free surface creation in underground drifts and tunnels

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The height of the down sprue is 175 mm and its CS are at the base is 200 mm2. The CS area of the horizontal runner is also 200 mm2. Assuming no losses, indicate the correct choice for the time (second) required to fill a mould cavity of volume 106 mm3. (Use g = 10 m/s²) (a) 2.67 (b) 8.45 (c) 26.7 (d) 84.50
Using Castigliano’s Theorem
In electric discharge machining, why the taper structure is generated when using normal flow of thedielectric fluid? P lease also give suggestion s to avoid the taper structure
A sprue in a sand mould has a topdiameter of 20 mm and height of 200mm. The velocity of the molten metalat the entry of the sprue is 0.5 m/s.Assume acceleration due to gravity as9.8 m/s2 and neglect all losses. If themould is well ventilated, the velocity(upto 3 decimal points accuracy) of themolten metal at the bottom of the sprueis ______ m/s.
Please solve this question, Thank you ery much.
5 UEME1233 MANUFACTURING TECHNOLOGY I (а) 25 mm on a layered structure of natural fibre-reinforced polymer composite. He encountered delamination problem in the workpiece (Figure 3) when he used conventional cutting tool to drill the hole. Instead of using conventional machining process, discuss ONE suitable advanced machining process that can be applied for this machining purpose and predict TWO possible limitations for the selected process. Q3. An engineer would like to drill a square hole of 20 mm x 20 mm with depth of (Word limit: ~100) Cutting Tool Delamination – Composite Material Figure 3. Delamination of the composite material. A resistance welding is performed to join two 2-mm thick stainless steel sheets (b) with ten 6-mm diameter spot welds produced concurrently. The resulted weld nugget each has average 3 mm in thickness. Calculate the required welding current and energy consumption for the welding if ten seconds are needed for the whole welding operation. Given that the…
what is Huebsher equation ?
Hi please help me with this question. Thank you very much. Please also explain the solution. Thank you
Q.3- Choose the correct answer of the following: 1. Injection molding is a type of: (a) Vacuum casting (b) Centrifugal casting (c) Squeeze casting (d) Die casting 2. From various casting processes, investment casting process is the suitable operation for manufacturing of: (a) Engine blocks (b) Gears (c) Jewelry (d) Car wheels (e) Pipes 3. The welding process by (GMAW) process is (a) Slower than, (b) Faster than, (c) at same speed as (d) at unpredictable speed. 4. The clearance angle is provided on the tools with a view to (a) Strength the tool. (b) Shear off the metal. (c) Prevent the tool from rubbing on workpiece (d) Facilitate easy flow of chips. 5. Chances of crack propagation are more in: (a) Cold working process (b) Hot working process (c) Both of the above (d) None of the above 6. For machining of carbide material which of the following tool will be preferred? (a) Zero rake angle tools. (b) Large positive rake angle tools. c) Large negative rake angle tools (d) Small point angle…
Molten zinc is used in a molding process. It is poured through an inlet whose area is 7,5 m2, The head of metal of pouring basin height is 3 m, and the head of metal of pouring basin plus sprue is 2 m. What would you recommend to be the maximum area of the exit location of the sprue?
Please complete and clear solution with diagram
Can you please simplify the solution for this problem. Kindly clarify also if I am wrong I think our prof forgot to put the cos(10) for the distance of the restultant. (For the solution below)