answer fast (d)Hand arm vibration is a physical hazard which transmitted to the worker's hand duringoperating handheld machine. The worker exposed to hand arm vibration at x-axis = 5m/s², y-axis = 3 m/s² and z-axis = 2 m/s² for 1 hour operating the power tool machine.Mathematical formula for vibration total value is anv = √√ahwx + anwy + awz anddaily vibration exposure is A(8)= ahv Toi.ii.Plan the management process flow on how to control the risk. Illustrate two(2) examples of control measuresDetermine the total daily vibration exposure, A(8) value and compare whetherthe vibration exceed the exposure action value (EAV) of 2.5 m/s².

Write the given data. ahwx=5 m/s2ahwy=3 m/s2ahwz=2 m/s2

(d) Hand arm vibration is a physical hazard which transmitted to the worker's hand during operating handheld machine. The worker exposed to hand arm vibration at x-axis = 5 m/s², y-axis = 3 m/s² and z-axis = 2 m/s² for 1 hour operating the power tool machine. ahwx + ahwy +ahwz and Mathematical formula for vibration total value is ahv = daily vibration exposure is A(8)= ahv To ii. Plan the management process flow on how to control the risk. Illustrate two (2) examples of control measures Determine the total daily vibration exposure, A(8) value and compare whether the vibration exceed the exposure action value (EAV) of 2.5 m/s².

(d) Hand arm vibration is a physical hazard which transmitted to the worker's hand during operating handheld machine. The worker exposed to hand arm vibration at x-axis = 5 m/s², y-axis = 3 m/s² and z-axis = 2 m/s² for 1 hour operating the power tool machine. ahwx + ahwy +ahwz and Mathematical formula for vibration total value is ahv = daily vibration exposure is A(8)= ahv To ii. Plan the management process flow on how to control the risk. Illustrate two (2) examples of control measures Determine the total daily vibration exposure, A(8) value and compare whether the vibration exceed the exposure action value (EAV) of 2.5 m/s².

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

122 1.17 The tripod shown in Fig. 1.73 is used for mounting an electronic instrument that finds the distance between two points in space. The legs of the tripod are located symmetrically about the mid-vertical axis, each leg making an angle a with the vertical. If each leg has a length / and axial stiffness k, find the equivalent spring stiffness of the tripod in the verti- cal direction. CHAPTER 1 FUNDAMENTALS OF VIBRATION FIGURE 1.73 A tripod carrying an electronic instrument.
A vehicle moving horizontally gets a load of wind resistance acting in the opposite direction to the vehicle's motion F M cv? v is the horizontal speed of the vehicle. F is the thrust that comes from the vehicle engine c damping coefficient for wind resistance force (c =0.20 N.sec2/m2) M is the mass of the vehicle (M = 1000 kg) Using Newton's 2nd law, we get the equation of motion dv 1000- + 0,2 v² = F dt At steady state the speed of the car is vo = 30 m/s and thrust F, = 0.2 v3 = 180 N. If the car is moving at a speed around steady state v = vo + dv = 180 and F = F, + 8F, derive a linear differential equation connecting d(dv) ,8v and SF. dt
Vibrations Engineering: A rope of a pendulum has a length of 2 meters. What is the natural frequency of the system for small angles in hertz? (Express the final answer in 4 significant digits)
E. In Exercises I and 2, find the domains and ranges of f, g. f+ g. and f'g. 1. f(x) = x, g(x) = Vx-1 2. f(x) = Vx + 1, g(x) = Vx-I %3D %3D %3D
Q4. Two are applied to the pipe AB as shown. Knowing that the pipe has inner and outer diameters equal to 35 and 42 mm, respectively. Determine the normal and shear stresses at (a) point a, (b) point b.
۱:۳۵ ۱ ص STATIC QU... -> FIND moments around O, A and B 500N 1 900N 60° В 4m A 5m CU
True or false Degree of freedom of a mechanical system define its configuration by the number of independent parameters
A foreman is exposed to the hand tool vibration for 31 minutes with the vibration values of ax = 44 m/s2 , ay = 12 m/s2 , and az = 9 m/s2 . The foreman has completed his works for period of 8 hours. Calculate the vibration total value, ahv and its daily vibration exposure, A(8). Analyze the daily vibration exposure to the worker based on the Vibration Regulation: EAV and ELV and provide your commen
A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance measured along the beam; [x]=[L] y = displacement of the beam; [y]=[L] = circular frequency of vibration; []=[T1] = mass of the beam per unit length; []=[ML1] D = bending rigidity of beam; [D]=[FL2] Show that the equation is dimensionally homogeneous. Note that [F]=[MLT2] see Eq. (1.21:).
4) For what values of m is y = Aemx a solution of y" – 3y' + 2y = 0
EFx=0= (0.433 F1) - (0.667 F2) - (0.866 F3) + (0.342 P) EFy=0= - (0.250 F1) + (0.667 F2) EFz=0= (0.866 F1) + (0.333 F2) + (0.500 F3) - (0.940 P) Find the magnitude of F1, F2, and F3
36- O A) 30 i- 19 k Nm B) 30 i+9k Nm C) 30 j-9k Nm O D) 12i+30j-9k Nm O E) 9j+30 k Nm