Design A bracket is cantilevered to steel channel using 8 bolts as shown in Fig . 1. It carries an eccentric load of 80 kN at an eccentricity of 250 mm . Diameter of each bolt is 20 mm Compute the stress at bolt B. ( dimensions in mm , use bolts M 16 X 2 )

Q: A converging diverging nozzle is supplied by air from large reservoir where the temperature is 400K.…

A: Temperature T0 = 400 K Velocity at inlet section V1 = 120 m/sCp = 1005R = 287 y = 1.4

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: Given

Q: The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the…

A: Diameter of the cylinder made of the magnesium: Initial temperature of the clamp: Diameter of the…

Q: Given the following table for RTD, compute the Temperature at 113.4 Resistance Ω 112.06 112.44…

A:

Q: Two tension forces are applied to the top of the tower as show wire is also attached to the top of…

A: Given data is We have to find the Tension in the wire AB such that the resultant force is only in…

Q: FBD for half the pliers (front lever) b = 38 mm Pin 90° α-40° 15 mm Ry 50° Rx From geometry, we have…

A:

Q: Is there any relationship between a crystal and a grain? justify your answer.

A: Crystal:The crystal is defined as the highly ordered structure in that molecules or atoms are fitted…

Q: 5. A damped harmonic oscillator with spring constant k, mass m, and damping constant y is subjected…

A: The external force:

Q: Which Failure Theory(ies) is(are) used for a Ductile Material under Static Loading?

A: Ductile Material:A ductile material is a type of material that exhibits plastic deformation before…

Q: c. Determine critical load and critical stress for the column/axial member. Justify  selection of…

A: The column is fixed at both ends.External axial load appliedYoungs modulusDiameter of the…

Q: Water flowing through a pipeline with an internal diameter of 0.4 m moves at a velocity of 0.5 m/s.…

A:

Q: FM A B W₁ Wo F₁ FM Y a A B W₁ Br 1 C Wo

A: a=12 cm, b=24 cm and c=36 cmThe angle that the long axis of the tibia makes with the horizontal is…

Q: r₁ = 10 m r₂ = 14m 3 T₂ = 690 K 9" = 50 kW/m ³ h₁ = 10W/mK Vacuum There is an inner sphere and an…

A:

Q: A pressure cylinder has an outer diameter 210 mm, internal pressure 4.4 MPa, and maximum allowable…

A: Given Data

Q: energy balance

A: for writing energy balance for any combination process we need to some factors like-1- Energy…

Q: à more precise method of estimating uncertainty in experimental results presented by Kline and…

A:

Q: Which of the following is true for crystallographic points, directions, and planes. To indicate a…

A: Crystallography: Crystallography is the branch of science that deals with the study of crystals and…

Q: Write the general energy balance for any combustion process. Is my answer correct?

A: Combustion Reaction Equation:

Q: slope 0.00020, %90 of the section is filled with water, flowrate 83.5 m3/s, determine the diamater…

A:

Q: Calculate the surface area required when the cooling flow is 0.4 kgs-1 for both a co-flow and…

A: Hot fluid (exhaust gases):Inlet temperature of hot fluid is ,Outlet temperature of hot fluid is…

Q: There is a tank with a radius of 1.0 m open to the air at the top and another tank with a radius of…

A:

Q: The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on…

A:

Q: A P collar slides along the OA pipe. A PC elastic cord is attached to it and it is held at point C…

A: BC=0.3mOB'=0.18mCA=0.24+0.12=0.36mnow look at the following edited figureto find OP distance

Q: Hot water at 160 ⁰C is passing through a pipe, and it is lagged with a plastic covering. The…

A: Hot water,  Ti  = 160 ⁰Ck= 0.2 Wm-1K-1 h = 16 Wm-2K-1T ∞ = 25 ⁰C

Q: Find the transfer function for the system illustrated in Figure P2.59. Express the transfer function…

A: m = 10 KgK1 = 400 N/mC = 14.14 N-s /mK2 = 100 N/m

Q: Heat transfer through composite walls The wall of a refrigerated van is of 1.5 mm steel sheet at…

A: GivenTemperature at outer surface, To==(273-15) K=258KTemperature at outer surface, Ti=

Q: 1. Two iron samples with different grain sizes are tensile tested. The grain size of sample A is…

A: The size of grain A and B is 1.1 and 0.37 μm respectively.

Q: Steam and ammonia enter a counter-current heat exchanger, both at 1 bar, with specific enthalpy…

A: Counterflow Heat exchanger with steam and ammonia.Entry pressures of both fluids are 1 bar.change in…

Q: A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the system has a…

A: The power transmitted, P = 4 kWThe diameter of the smaller pulley, d = 150 mmThe speed of the…

Q: We want to determine the minimum volume of concrete s=2.8 that is required to maintain the gate…

A: Given:The mass is .The density is .Free body diagram:Here,  is tension in string,  is force by water…

Q: Q3 For a university building, steam at 150°C for heating is supplied from a remote boiler house…

A:

Q: The worktable of a numerical control machine tool is driven by a closed-loop positioning system…

A: Given data as below:pitch p = 0.25 in/revthe distance at which table moved x = 7.5 infeed rate fr =…

Q: (Pr. 1) In an isotropic medium, Poisson's ratio v relates Young's modulus to either the shear…

A: Hi,   As per the guidelines, we can solve only first question for you since the exact one is nor…

Q: Two couples act on a rectangle with a base of 7 m and a height of 4 m. Determine the magnitude and…

A:

Q: velocity of the gear at the instant the spring compresses 20 mm. Neglect friction.

A: Given DataThe Mass of the Gear A m2=0.3 KgThe radius of the gear A r=50 mm=0.05mThe radius of…

Q: 1- A refrigeration system shown below uses R-134a. The refrigerant comes out evaporators and flash…

A:

Q: C. 3. A trunk of mass M is on a ramp. A rope pulls on the trunk horizontally as shown but the trunk…

A: The above diagram shows a trunk having mass M is pulled with the help of a horizontal rope but it…

Q: Q.2.: Air (R = 0.287 kPa. m³/kg.K) initially at 0.75 bar, 1000 K, and occupying a volume of 0.12 m³…

A:

Q: The Force of F = 27.6 N acts on the bracket as shown. Determine the moment of the force about the…

A:

Q: A fluid is flowing in a 20 cm diameter pipeline with a velocity of 5.50 m/sec. The pressure at the…

A: Given Data:Diameter of pipe = 20 cm Mean velocity = 5.50 m/secPressure at the center of the pipe =…

Q: A rigid, insulated tank whose volume is 2 L is initially evacuated. A pinhole leak develops and air…

A: The volume of the tank, V = 2 LThe air pressure, Pa = 1 abrThe air temperature, Ta = 30 CThe final…

Q: Answer the questions below for the following system. Young's modulus and Poison's ratio can be taken…

A:

Q: Q.1) Draw Free-Body diagrams of each of the three cylinders shown below. Each of the cylinders has a…

A:

Q: Two spur gears are to have a ratio of 9:3 and a 7mm module. If the center distance is to be…

A: According to our guidelines, we are supposed to answer the first three sub parts . please re-post…

Q: Task Ib 13 i. 12 P 270 N 70° [All forces: FPQ, FPR, FRS S 55° Figure Ib shows a crate with a weight…

A: shows a crate with a weight of 270 N supported by the vertical pole RS. Based on the figure, To…

Q: Trusses are made up of Joints and Members. Every member in a truss is: a Zero-Force Member. O in…

A: Trusses are made up of joints and members. Find: condition or property of Every member in a truss.

Q: 18-57. A spring having a stiffness of k = 300 N/m is attached to the end of the 15-kg rod, and it is…

A:

Q: The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to…

A: Write expression for torque due to forces.Here T is torque, F is magnitude of couple forces, and a…

Q: Given the two views of a solid and an auxiliary reference plane, draw the auxiliary view and…

A: Draw Auxiliary view of the given figures.

Q: Can the statue be dragged without tipping? O Yes No Frip xN If the movers can apply the force…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.