Question 3:a) Design a circuit which will add a 4-bit binary number to a 5-bit binary number. Use five fulladders. Assume negative numbers are represented in 2's complement. (Hint: How do you makea 4-bit binary number into a 5-bit binary number, without making a negative number positive ora positive number negative?)b) A half adder is a circuit that adds two bits to give a sum and a carry. Give the truth table for ahalf adder, and design the circuit using only two gates. Then design a circuit which will find the2's complement of a 4-bit binary number. Use four half adders and any additional gates. (Hint:Recall that one way to find the 2's complement of a binary number is to complement all bits,and then add 1.)

There are two independent questions. We are authorized to answer one question at a time, since you…

Design a circuit which will add a 4-bit binary number to a 5-bit binary number. Use five full adders. Assume negative numbers are represented in 2's complement. (Hint: How do you make 4-bit binary number into a 5-bit binary number, without making a negative number positive or a positive number negative?) a

Design a circuit which will add a 4-bit binary number to a 5-bit binary number. Use five full adders. Assume negative numbers are represented in 2's complement. (Hint: How do you make 4-bit binary number into a 5-bit binary number, without making a negative number positive or a positive number negative?) a

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

How to build this circuit? (on Digital or Logisim) Binary-coded decimal is an alternative method of representing integers using binary. In it, each base-10 digit is represented by four bits, thus each nibble takes one of 10 values (0000 through 1001). Therefore, using BCD, 42 (decimal) is represented as 0100 0010 (binary) and 196 (decimal) is represented as 0001 1001 0110 (binary). Create a circuit in Logisim that accepts as input a pair of two-digit integers represented as BCD and outputs their sum in BCD. Any and all Digital components are fair game. You can assume that all inputs will be valid BCD-encoded numbers.
1. Gray code to Binary converter: Gray code is one of the codes used in digital systems. It has the advantage over binary numbers that only one bit in the code word changes when going from one number to the next. (See Table 1). Design a combinational circuit with 4 inputs and 4 outputs that converts a four- bit gray code number into an equivalent four-bit Binary number. Use Karnaugh map technique for simplification. Use LogicWorks for pre-lab demonstrations. Select the library "7400dev.clf* in the Parts Palette and then select the XOR chip 74-86. This would give you a set of 4 XOR's as shown in Fig. 1, just like the hardware chip 74-86. You could use as many as needed from these XOR gates in your design. Get back to ALL LIBRARIES and select switches for the inputs and Binary Probes as indicators of the outputs. Verify your design in the pre-Lab. During the Lab construct the circuit and verify its operations.
DISCUSSION: 1- Is the Gray code arithmetic code? Why? Where this code usėd? 2- What is the parity bit? 13- Design five - bit odd parity checker? 4- a) What are the main applications of the comparator? /b) Design two – two bit comparator. -5- Convert five.bit Gray to binary code, write truth table and draw the circuit diagram. 2-5
1) What is the biggest binary number (decimal value) you can write with 6 bits? What is the biggest binary number (decimal value and in terms of n) you can write with n bits? If you want to represent the decimal numbers from 0-16, what is the minimum number of bits you will need? Convert the decimal number 238 to binary number. (ZERO point if not showing steps/calculation!)
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
A 4-bit binary up/down counter is in the binary state of zero. The next state in the DOWNmode is (a) 0001 (b) 1111 (c) 1000 (d) 1110
Logic Gates:* 7404LS (NOT)* 7408LS (AND)* 7432LS (OR)* 7400LS (NAND)* 7402LS (NOR)* 7486LS (EX-OR)Or you can use 74HCxx versions. Task 2: 4 INPUT PRIORITY ENCODERa) Write the truth table.b) Find the outputs in terms of min terms using minimal expression.c) By using K map, find the simple/simplest expression of theoutputs.d) Draw the circuit diagram. (Simulation design will be accepted.)e) Simulate the circuit & explain your results. (Please do notdesign separate simulations for each output. You should design ONEsimulation including all inputs and outputs.)
Design a combinational circuit with 3-inputs and 1-output. The output is equal to logic-1 when the binary value of the input is less than 3. And the output is logic-0 otherwise.
parity generator design, construct and test a circuit that generates an even parity bit ffrom four messages bits . use XOR gates. adding one more XOR gate, expand the circuit so that it generates an odd parity bit also.
Assume that the exclusive-OR gate has a contamination delay of 3 ns and that the AND or OR gates have a contamination delay of 2 ns. What is the total contamination delay time in the 4-bit adder? Note: your answer should include only the value of the delay without the unit (only the number) Note: Submit your work on paper as well А- B- Cin- Cout Answer:
How many full adder circuits are needed to add 2 five bit binary numbers. O a. 5 O b. 7 O c. 10 O d. 2