Design an amplifier with an overall gain Av = -15 where the input voltage vi has a source impedance (Ri) of 2kW and the amplifier has an input impedance of 4kW, VBE,on = 0.7V and β =200. The amplifier requires a maximum output voltage swing. Determine all resistor values, Ai and the maximum voltage swing.

Design an amplifier with an overall gain Av = -15 where the input voltage vi has a source impedance (Ri) of 2kW and the amplifier has an input impedance of 4kW, VBE,on = 0.7V and β =200. The amplifier requires a maximum output voltage swing. Determine all resistor values, Ai and the maximum voltage swing.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

Plz do it byhand. Complete solution plz
20. The resistance R and a 2 μF capacitor are connected in series across 200-V dc supply. Across the capacitor is a neon lamp that strikes at 120 volts. Calculate the value of R to make the lamp strikes 5 seconds after the switch has been closed. A. 4.89 kΩ B. 4.89 MΩ C. 2.73 MΩ D. 2.94 MΩ
4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?
Solve 2,3 only.Note the load resistance is 10 ohm and frequency 60 Hz
NOTE: Solve this as soon as possible, I need this urgently. Determine the currents Iy and I, in the circuit below 6 mA 1.51 1 mA
Problem 15. A source of e.m.f. of 15 V supplies a current of 2A for six minutes. How much energy is provided in this time?
2. For the characteristics below. Determine the ff: a. ac resistance at l,=2mA. b. ac resistance at I,=25 mA c. Compare the results of part (a) and (b) to the dc resistances at each current level. Ip(mA) 30 25 20- 15- 10- 2 Ala 0.1 0.2 0.3 0.4 0.5 0.6 0.7 08 0.9 Vo(V) AV
NOTE: Solve this as soon as possible, I need this urgently. Determine the currents I, and I, in the circuit below 6 mA 1.51 1 mA
An aluminum wire 5m long and 2mm diameter is connected in parallel with a copper wire 3m long. The total current is 4 A and that in the aluminum wire is 2.5 A. Find the diametre of the copper wire. The resistivity of copper wire being 1.7 micro ohm meter and that of aluminum taken Al 2.6 micro ohm meter
In the figure below, q1 = +2.00 nC and q2 = -8.00 nC. At what postion can an electron be placed and experience zero net electric force from 9₁ and 92? y 91 + O at x 13.33 cm O at x = 6.67 cm O at x = -10 cm O at x = 3.33 cm 92 10 cm > X
Find the current in i in the electrical circuit below 54 k0 SV a. 15uA Ob.20u A c.25JA Od25pA A Moving to another question will save this response. mc021-1jpg: mc030-2jpg mc024-3 pg Verified Venfied 1:07 2021 Pr EN
An aluminium rod with square cross section is 1.3 m long and 3.8 mm on edge ) What is the resistance between its ends? The resistivity of aluminium is 2.75 - 10-8 Q.m. (ii) What must be the diameter of a cylindrical copper rod of length 1.3 m if its resistance is to be the same as that of the aluminium rod? The resistivity of copper is 1.69 * 10-8 Q.m. (iii) Calculate the current (in A) and the current density (in A/m^2) of the cylindrical copper if the potential drop across the ends of the wire is 0.060 V. Select one: a. (i) 3.27 x 10-30 (ii) 15.3 × 10-3 m (iii) l= 18.3 A and J=1 x 105 A/m2 b. (i) 2.50 x 10-3n (i) 3.4 × 10-3 m (iii) l= 24 A and J=2.64 x 10 A/m2 c. (i) 2.50 x 10-3 (ii) 3.4 x 10-3 m (iii) l= 24 A and J=2.08 x 106 A/m2 d. (i) 3.27 x 10-3 (ii) 8.14 x 10-3 m (iii) l= 18.3 A and J=2.64 x 106 A/m2