Problem 2: (M2)Design engineers in many situations must justify their selection of material. Your role in a mechanicaldesign company that manufactures steel pipes is to confirm the maximum stresses imposed by a 250 psioil pressure on the pipe wall, which acts as a pressurized cylinder once the gate valve is closed.If the pipe diameter is 1 foot and its wall is 0.25 inches thick. Evaluate the longitudinal and hoop stressesat point A.ValveAoil inFigure.3: Steel oil pipe

Pressure, P = 250 psi Thickness, t = 0.25 in Diameter, d = 1 foot = 12 in a) Longitudinal stress…

Design engineers in many situations must justify their selection of material. Your role in a mechanical design company that manufactures steel pipes is to confirm the maximum stresses imposed by a 250 psi pil pressure on the pipe wall, which acts as a pressurized cylinder once the gate valve is closed. If the pipe diameter is 1 foot and its wall is 0.25 inches thick. Evaluate the longitudinal and hoop stresses at point A

Design engineers in many situations must justify their selection of material. Your role in a mechanical design company that manufactures steel pipes is to confirm the maximum stresses imposed by a 250 psi pil pressure on the pipe wall, which acts as a pressurized cylinder once the gate valve is closed. If the pipe diameter is 1 foot and its wall is 0.25 inches thick. Evaluate the longitudinal and hoop stresses at point A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel tube of 200 mm external diameter is to be shrunkonto another steel tube of 60 mm internal diameter.The diameter at the junction after shrinking is 120 mmbefore shrinking on, the difference of diameters at the junctionis 0.08 mm. Calculate the radial pressure at the junctionand the Hoop stresses developed in the two tubes aftershrinking on.Take E = 2 x 10³ N/mm²
A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa.Calculate the tangential stress in the steel.
A steel tube of 300 mm external diameter is to be shrunk on to another steel tube of 90 mm internal diameter. After the diameter at the junction is 180 mm. Before shrinking on the difference at the junction is 0.12 mm. Find (i) The radial pressure at the junction; (ii) The circumferential stresses developed in the two tubes after shrinking on.
Q3: (a) describe the location and function of the following: \i. Gudgeon pin ii. Rod shank ii.Large end (b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
DESIGN Situation No. 1 – A pressure vessel 360 mm in diameter it to be fabricated from steel plates. The vessel is to carry an internal pressure of 6 MPa. 1. What is the required thickness of the plate if the vessel is to be cylindrical and the allowable steel stress is 120 MPa. 2. What is the required thickness of the plate if the vessel is to be spherical and the allowable steel stress is 120 MPa. 3. If the vessel to be fabricated is cylindrical using 12 mm thick steel plate, what is the maximum internal pressure that the vessel can carry if the allowable steel stress is 60 MPa.
A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa.Calculate the longitudinal stress in the steel.
The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of pressure of p. The state of stress at point "a" on the surface of the tank is represented by stress components with an unknown stress element rotation angle of 0. Note that, the two normal stress components for x'y' system (note: not xy system!) are known: ox, = 120 MPa and Oy = 180 MPa, but the shear stress component (T,) is unknown. Determine: (1) the principal stresses at point a ; (2) Tx'yı ; (3) rotation angle of 0 . y 180 MPa 120 MPа х 0 = ? a Tyy = ? tank cross section stress state at point a
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.10 ksi. Determine the hoop stress in the wall of the tank.
Show complete solution pls A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. Thechanges in dimension caused by an increase in temperature of 80°C for the:1. Outside diameter 2. Inside diameter 3. LengthNote: All answer must be round off up to 3 decimal places.
(b) Determine the thickness of a plain cylinder head for 0.3m cylinder. The maximum gas pressure is approximately 3.2N/mm. Design the studs also for the cylinder cover. Assume the allowable hoop stress =42 N/mm' for cast iron; the allowable tensile stress for material of studs =63 N/mm?
SolveSample Problem 4.1.All remain as presented, except for the following changes.The factor ofsafety is now 2, and not 3.As Presented, the thickness of the tube is uniform. In the new one that you are solving,let the thicknessesof the top and bottom be the same,ttb, and the thicknesses of theleft and right be the same,tlr.Theheightand the width of the tube are still respectively 5 in and 3.25 in.As you make thesethickness changes,you are to keep thetotal mass of the tube unchanged. Answer the same questions (a) and (b).Explain your findings
QUESTION 2 A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers. It is subjected to an internal pressure of 5.2 MPa. Calculate the circumferential and longitudinal stress induced. Which axially applied compressive load would reduce the longitudinal stress to zero?