Design the steel reinforcement for flexure for the beam to carry the loads shown in the figure below, use the following data: width of the beam b= 300mm , effective depth d=600mm, side cover =40mm, effective cover = 60mm,use f'=28MPA ,fy = 414MPA, useØ 25mm steel bars. %3D W =80kN /m 6m

Design the steel reinforcement for flexure for the beam to carry the loads shown in the figure below, use the following data: width of the beam b= 300mm , effective depth d=600mm, side cover =40mm, effective cover = 60mm,use f'=28MPA ,fy = 414MPA, useØ 25mm steel bars. %3D W =80kN /m 6m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Design economical spacing of 10 mm diameter stirrups for the beam which carries the loads shown. Design shear reinforcement of prestressed beam with the following properties listed. Properties: f^c=28 MPa fy = 276MPa Aps = 800 mm² Ds = 10mm Dm = 18mm fse = 800 MPa fpu = 1500 MPa fpe = 860 MPa Pe = 250kN
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 28 kips, w = 3.8 kips/ft, LAB = 4.6 ft, Lec = 4.6 ft, and Lco = 15.0 ft. Determine the magnitude of the maximum bending stress in the beam. %3D %3D B |C D LAB LBC LCD Answer: Omax = ksi
Fill in the blanks: Determine the required tension steel area of the T beam with given properties below. Width of flange bf= 500 mm Width of web bw = 400mm Thickness of flange tf 140 mm Effective depth d = 380 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 30 MPa Yield stress of steel bar fy = 300 MPa Mu = 448 kN-m As = mm2 CS Scanned with CamScanner
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield strength 420 MPa. If bar centroid is located 70 mm from the bottom edge of the beam and f'c = 21 MPa, calculate the design moment strength in kN-m. Write your answer with 2 decimal places only.
Design the flexural reinforcement of the cantilever beam shown below for the given loading and data. The loads shown include the self-weight. f. = 28 MPa ; fy 420 MPa Main Reinforecemnt : 020mm ; Stirrups : Øø10mm P= 70kN -1000mm W= 100 kN/m 150mm 450mm -2.0m 400mm Page 4
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 3.8 kips/ft, LAB = 5.2 ft, LBc = 5.2 ft, and LCD= 14.4 ft. Determine the magnitude of the maximum bending stress in the beam. %3D D B LAB LBC LCD Answer: ksi Omax
A simply supported beam is reinforced with 5-p25 mm at the bottom and 2-020 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN -m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = __ mm
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = mm Design strength of the beam section to the nearest whole number = kN·m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = kN/m (to the nearest whole number)
1. A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determine the safe compressive load. Fy = 248 MPa, E= 200 GPa. Use AISC/NSCP Specs. 450 mm -cover plate 'I 12 mm y2 IP d2 10 m C 310 x 37 A = 4720 mm? d = 305 mm bf = 77 mm tf = 12.7 mm tw = 9.8 mm C 310 X 37 a) Both ends of column are fixed b) Both ends of column are hinged c) One end fixed, the other end hinged Use design values of k. tw d=305- Ix = 59.9x10° mm ly = 1.85x10° mm x = 17.1 mm x=17.1