Determine (a) the distance a for which the maximum absolute value of the bending moment in the beam is as small as possible, (b) the corresponding maximum normal stress due to bending. (a) a = (b) a= 2 kips ft ksi C 15 kips D 10 ft-7 ft → B I W14 x 22

Determine (a) the distance a for which the maximum absolute value of the bending moment in the beam is as small as possible, (b) the corresponding maximum normal stress due to bending. (a) a = (b) a= 2 kips ft ksi C 15 kips D 10 ft-7 ft → B I W14 x 22

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the magnitude of the pin reaction at B by (a) ignoring the fact that BD is a two-force…

Q: Q-The strength of a fully matured concrete sample is 500 kg/cm². When cured at an average…

Q: A temporary diversion has been constructed on a highway of -3% gradient due to major repairs that…

A: The gradient of temporary diversion, G = -3% The distance, drivers can see the sign informing them…

Q: A 6-yd hydraulic shovel with a bottom-dump bucket is excavating common earth. The swing angle is 75…

A: Part 1) Part 2)

Q: Theory of structure Drow S.F.d A.F.D B.M.D

Q: An existing sewer at P is to be continued to Q and R on a falling gradient of 1 in 150 for plan…

A: Answer Let us draw the digram based on the given data as shown below Height of Instrument = 89.52…

Q: Find the work if force of 66 N displace the roller by 0.22 m

A: Objective: To determine the work done by the given force in moving the roller. Given: Force (F) =…

Q: Find the Y location of maximum shear stress.

A: To find the location of maximum shear stress for the section shown in the figure.

Q: H. beam with dimension of (300x 600) mm f = 21 MPa and f = 420 MPa ( C 4m PĮ + 4m with including…

A: Answer We are given Load P = 25 KN beam width b = 300 mm beam depth h = 600 mm effective depth d =…

Q: Water-cement Water = 191.6 liter The required cement content will be ratio = 0.50

A: Given data: Water cement ratio, wc=0.5 Water, w = 191.6 liter Required cement content, c =?

Q: Degree of saturation

A: Introduction : The given question is related with geotechnical engineering . In this question data…

Q: Solve the absolute maximum bending moment and absolute shear force in the simply supported beam…

A: A simply supported beam is loaded by a train of load, which consist of only concentrated loads. To…

Q: What are the different dimension styles used in AutoCAD?

A: This question is related to the Autocad from Civil Engineering. In this question ask about the…

Q: For the frame and loading P = 480 lb shown, determine the internal forces (axial for of the…

A: P=480lb To find internal force at point j

Q: A 0.30-m-diameter cork ball (SG = 0.21) is tied to an object on the bottom of a river as is shown in…

A: Given data:- The given diameter of the cork ball, D=0.3 m The specific gravity of the ball is,…

Q: Problem 2: The structure consists of a solid rod of length 2L. On the left it is fixed to the wall.…

A: The given figures are shown below:

Q: 1.2. moving plate U plate = Umax Ufluid =0 u (velocity) A U fluid =Umax stationary plate F T j…

A: Given data:- The given two parallel plate velocities, u=1 cm/s The distance between two calculators…

Q: An anaerobic digester is operated with a hydraulic retention time (HRT) of 25 d and a flow rate of…

Q: 6- A Sample of saturated clay had a volume of 97cm and a mass. of 0.202 kg. When Completely dried…

A: Given Data Saturated clay volume = 97 cm3 Mass of saturated clay = 0.202 kg Dry volume of clay =…

Q: 75mmy 25mmp 24.0M 750mm Hg @56 = 13.6 Ve75mmg = 0.6m/s Reqd² h = ?

A: A pipe flow in which one end is open to the atmosphere and manometer is inserted at one point to…

Q: The beam is bolted or pinned at A and rests on a bearing pad at B that exerts a uniformly…

A: Given : Determine the shear and bending moment diagrams along the beam. We know Shear force diagram…

Q: The inextensible, rigidly jointed frame illustrated below is fully fixed at D and E and has a simple…

A: Given data : Indeterminate beam is given with different flexural rigidity Find : Distribution factor…

Q: A log weighing 830 lb is lifted by a pair of tongs as shown. Determine the forces exerted at E and…

Q: Calculate area of tensile steel for a singly R.C. beam 230 mm x 380 mm size and factored moment 50…

Q: What is the unit of measurement for rack space? Are normal racks tall?

A: This question is related to the AutoCAD and design and drafting from civil engineering.

Q: pletely fill up the missing data ((marked with “X”) and apply arith STA BMa 00 _0 7 TP1 25.622…

Q: Water is discharged through the drain pipe at B from the large basin at 0.03 m^3 /s. If the diameter…

A: Given : Discharge through the drain = 0.003 m3/s Diameter of drainpipe = 60 mm To Find : Determine…

Q: How many methods of plumbing, mentioning the reasons and reasons for each of these methods?

A: Basically, a pumping system involves two main purposes which are to supply water for different needs…

Q: 7. A 6-in.-long bronze tube, with closed ends, is 3 in. in diameter with a wall thickness of 0.10…

Q: A simply supported beam carries three concentrated loads as shown in the figure. a. Determine the…

A: A simply supported beam is given of span length of 24ft. On this beam, three concentrated loads…

Q: 2. For the cantilever beam shown in the figure, what will cause zero deflection at A? ANS. P=112.5 N…

A: Given Data:M=400 N-mSpan=4m To Determine: Load P that will cause zero deflection at A.

Q: What are Xrefs and its applications?

Q: 1. Determine the sum of the following sound levels (all in decibels): 68, 82, 76, 68, 74 and 81

A: Sound Levels: The sound level determines the intensity of the sound and classifies the intensity of…

Q: As shown in the figure, two aluminum rods AB and BC, hinged to rigid supports, are pinned together…

A: Given: P=6000lb, A=0.60in2, Compute: elongation of each rod and dispplacement at point B.

Q: Find the centroid of square from bottom of X axis having dimension 8 mm*8 mm

A: Given data : The width of square section b=8 mm The depth of square section d=8 mm Required :…

Q: Find the external reactions at support A (hinge or pin) and D. (roller) and the reaction of the…

A: Given: a=1mb=4 md=2 me=3 mg=2 mw1=2 kNmw2=5 kNmF1=20 kN Radius of the pulleyr=1 m To find: Reactions…

Q: A timber pile of length 8m and diameter of 0.2m is driven with a 20 kN drop hammer, falling freely…

A: Given data: Timber pile length, = 8 m Diameter = 0.2 m Driven with, w = 20 kN drop hammer Falling…

Q: V.2. applied a at can be on beam with dimension of (300x 600) mm f = 21 MPa and f= 420 MPa (neglect…

Q: A 6m El = constant E = 50 GPa I= 135(106) mm² 70kN-m Determine the slope and deflection at point b…

Q: d) If the aircraft has a takeoff weight of 7500 kg and flying at the indicated angle of attack, what…

A: Given, W = 7500 kg α = 4o

Q: In a fill section of a construction site, 1600 m³ of moist compacted soils are required. The design…

A: According to given data In a fill section of a construction site, 1600 m³ of moist compacted soils…

Q: How many separate fields should be included in a single RFI, and what are their purposes

A: This question is related to the Building design and drawing from civil engineering.

Q: If other materials were allowed to be used to strengthen the balsawood frame of the bridge, what…

A: In order to offer access to a physical impediment, such as a body of water, a valley, or a road, a…

Q: Calculate the forces in members BE and BD of the loaded truss. The forces are positive if in…

Q: Q7/ Oxygen at 30 °C and 300 kPa absolute pressure ex- pands isothermally to an absolute pressure of…

Q: For #5-7, assume there is a creek with a width of 4.6 m, depth of 23 cm, slope of 0.001 m/m, and…

A: Given data:- The given creek width is, 4.6 m The given depth is, 23 cm. The given slope is, 0.001m/m…

Q: For the particles in problem 3, determine the percent removal in a sedimentation basin with a depth…

A: Answer We are given Before flocculation Average diameter = 20 μm Specific gravity S = 2 After…

Q: A cohesive soil was tested in natural state and in remoulded state. If the cohesion of soil in…

Q: For the new cast (f=0.014) pipe system shown below, determine the flow rate in each pipe. Ignore…

A: Given : f = 0.014 Determine the flow rate in each pipe. Formula to be used : Darcy weisbach…

Q: Calculate the forces in members AB, BH, and BG. Members BF and CG are cables which can support…

Question

Determine (a) the distance a for which the maximum absolute value of the bending
moment in the beam is as small as possible, (b) the corresponding maximum normal
stress due to bending.
(a) a =
(b) a =
2 kips
ft
ksi
10 ft
15 kips
7 ft
I
W14 x 22

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Mass and mass related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1780 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 230 kip-ft, P = 24 kips, LAB = 5.2 ft, LBc = 7.8 ft. %3D MA A В C LAB LBC
X Your answer is incorrect. The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; I = 843 in.“]. Assume that the support at D can provide resistance %3D either up or down. For a loading of w = 5.4 kips/ft, determine: (a) the beam deflection vg at point A. (b) the beam deflection vc at point C. Assume LAB = 13 ft, LBc = 7 ft, LcD =7 ft, LDE = 6 ft. %3D A B E LAB LBC LcD LCD Lpe Answers: (a) VA = -0.65669 in. (b) vc = 0.024937 in.
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 × 106 mm4). For the loading shown, determine the beam deflection vc at point C. Assume P = 51 kN, w = 30 kN/m, LAB = LBC = 3.3 m, LcD = 1.9 m. B C D LAB LBC LCD Answer: vc = -17.22 mm.
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1570 in.“]. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 160 kip-ft, P = 10 kips, LAB = 9.0 ft, LBC = 13.5 ft. MA A В C LAB LBC Answer: (a) VA = in. (b) Ув in.
A beam is subjected to equal bending moments of M, = 3600 N-m. The cross-sectional dimensions are b = 115 mm, c 31 mm, d = 66 %3D mm, and t = 4 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. M2 M2 H. d (typ) b. Answer: mm (a) y= i 2= i ! mm4 %3D S= i ! mm3 MPa = Ho (q) MPа (c) OK = !MPa (d) Omax =
es A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, F Ra 1 X Y 12 Determine the section modulus of the beam. Select the correct response: 72113.831 mm³ 87833.695 mm³ 57962.384 mm3 45378.561 mm³ Ri 12
A beam carries a concentrated load W and a total uniformly distributed load W. (N/m). What safe value of W (Newton) can be applied if fbc < 100 MPa and fot s 60 MPa at negative value bending moment? Show the equation of the positive bending moment. 175 mm Wo N.A. 125 mm -2 m- 4 m R1 R2 INA = 24 x 104 mm
The simply supported beam consists of a W21x44 structural steel wide-flange shape [E = 29,000 ksi; I= 843 in."1. Assume that the support at D can provide resistance either up or down. Fora loading of w= 7.2 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB= 10 ft, LBc = 5 ft, LCD =5 ft, LDE=5 ft. B LAB LBC LCD LDE Answers: (a) VA = in. (b) vc = in.
Plz solve within 30min I vill give definitely upvote and vill give positive feedback
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1690 in.*). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA = 170 kip-ft, P = 30 kips, LAB = 6.1 ft, Lec = 9.2 ft. P MA В C LAB LBC Answer: (a) VA = in. (b) Vg = in.