Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 5 mm & Modulus of Elasticity 199 GPa. It is found that the specimen has undergone an extension of 1.2 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 4.9 x 10-3. Solution Cross-sectional Area, A (in mm2) Tensile Load, F (in N) Length of the Specimen (in mm)

Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 5 mm & Modulus of Elasticity 199 GPa. It is found that the specimen has undergone an extension of 1.2 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 4.9 x 10-3. Solution Cross-sectional Area, A (in mm2) Tensile Load, F (in N) Length of the Specimen (in mm)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.6.7P: A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 7 mm & Modulus of Elasticity 192 GPa. It is found that the specimen has undergone an extension of 1.2 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 4.2 x 10-³. Solution Cross-sectional Area, A (in mm²) = Tensile Stress, (in N/mm²): Tensile Load, (in N) = = Length of the Specimen (in mm)
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 8 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1.6 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain-induced due to the load "F" on the specimen is 4.1 x 10-3. Solution Cross-sectional Area, A (in mm²) Tensile Load, F (in N) Length of the Specimen (in mm)
Determine the elastic tensile load "F" that acts on mild steel specimen of Diameter 9 mm & Modulus of Elasticity 201 GPa. It is found that the specimen has undergone an extension of 1 mm due to the elastic load "F". Also, determine the length "L" of the specimen, if the strain- induced due to the load "F" on the specimen is 3.6 x 10-³. Solution Cross-sectional Area, A (in mm²) = 63.617 One possible correct answer is: 63.617251235193 Tensile Stress, (in N/mm²) 723.6 One possible correct answer is: 723.6 Tensile Load, (in N) = = 46033.261 One possible correct answer is: 46033.442993786 Length of the Specimen (in mm) 4.366 X One possible correct answer is: 277.77777777778
A tension specimen of circular cross-section tapers uniformly from 20 mmto 16 mm diameter over a gauge length of 200 mm. When an axial load of40 JcN is applied, the extension measured on this gauge length is 0-4 mm. Findthe modulus of elasticity of the material.Compare the strain energy in this specimen with that in a specimen of thesame material of uniform diameter 18 mm carrying the same load. (U. Lond.)
A cylindrical specimen of a steel alloy 10 mm in diameter and 100mm long is pulled in tension at a load of 23500N and the strain found to be 0.0015, the elongation will be: Select one: 0.15mm Ob. 0.023mm 0.100mm Od. 0.0015mm
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
In our previous topic regarding strain, repeat the problem on the strain using thefollowing parameters:F = 150000 +/- 150 lbfSide length = 1.2 +/- 0.025 inModulus of Elasticity = 25000 +/- 11.5 ksiDetermine the relative error. Is it above or below the accepted 5% error?
A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?
PROPAGATION OF ERRORS Determine the range of values to which the strain will be calculated.F = 150000 +/- 150 lbfSide length = 1.2 +/- 0.025 inModulus of Elasticity = 25000 +/- 11.5 ksiDetermine the relative error. Is it above or below the accepted 5% relative error?
Problem 2: A specimen of steel having an initial diameter of 0.503 in was tested in tension using a gauge length of 2 inches. The following data were obtained for the tension. Plot the stress strain data and determine the modulus of elasticity, and the yield strength of the material. Elastic State Load P Ibf Elongation in 1 000 0.0004 2 000 0.0006 3 000 0.0010 4 000 0.0013 7 000 0.0023 8 400 0.0028 8 800 0.0036 9 200 0.0089
The relationship between true strain (ɛ-) and engineering strain (ɛ) in a uniaxial tension test is given as (a) & = In (1 + &7) (c) &7= In (1+ E) (b) ɛg = In (1- E) (d)= in (1- E) %3D %3D