Determine the maximum effective net area of the fillet weld using the maximum weld allowed by the code. Length of 550 mm and a maximum weld size is 12.5 mm. * P 10,601 sq.mm. 9721 sq.mm. 8840 sq.mm. O 1100 sq.mm.

Determine the maximum effective net area of the fillet weld using the maximum weld allowed by the code. Length of 550 mm and a maximum weld size is 12.5 mm. * P 10,601 sq.mm. 9721 sq.mm. 8840 sq.mm. O 1100 sq.mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: One plate of size 100 mm x 12 mm is lap joined to another plate of size 200 mm x 12 mm by fillet…

Q: Determine the total LFRD design strength and the total ASD allowable strength of the 5/16 – in E70…

A: We will solve this question in step no. 2

Q: Determine the tensile capacity of the angle shown. The diameter of the rivet is 7/8". Fy = 36 ksi,…

A: The net width of the given angle section is: wg=1+2+2+2.4+2.4+1.2=11" Effective hole diameter d0 =…

Q: ical steel press r with a wall th d to an interno

Q: 7. The rebar is to be lapped 18 inches.

A: Show the footing plan as in Figure (5-26) Show the footing plan as in Figure (5-27) Show the…

Q: 200 x 20 mm Plate • 5310 x 47.3 C310 x 30.8 Semi-circle Weld, 10mm radius

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

Q: 13) Welds are actually weaker than the steel members they join? T or F 14) Pumping concrete allows…

A: 13: Welding is process used to join two metal surface . Weld are weaker than steel they join . The…

Q: i) Groove welds ii) Fillet welds ii) Slot and Plug welds

A: Groove welds : The most popular weld with a root opening is a groove weld. There is a distance…

Q: Solve a 100 x 100 x 10mm angle is to be welded to a gusset plate shown. The angle carries a load of…

A: Given strength of fillet weld 94 mpa Size of fillet weld = 8 mpa Load to be carried = 185 kn

Q: LC hoop=2011PH 90 MPA %3D ) Find stresses in the eotated elementt uith 9= 30° us ing the MOHR's…

A: Hoop stress acts in circumferential direction and longitudinal stress acts along the length of…

Q: afe strength of a 5/16 in. fillet weld if it's actual length is 3 1/2 in. and the allowable unit…

Q: One leg of an 8 x 8 x 3/4 angle is to be connected with side welds and a weld at the end of the…

A: Fillet weld: This weld is a joint made by joining two metal pieces together which are perpendicular…

Q: A hanger is suspended from a plate that is welded to a wide flange beam as shown. The plate requires…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Find the Load Capacity of the weld if the throat thickness is 8. 13 mm, Nominal Tensile Strength, Fu…

A: t = 8.13 mm l = 400 mm Fu = 520 MPa = 520 N/mm^2 P = ?

Q: Which of the following most nearly gives the throat of a 9 mm fillet weld? a. 4.5 mm b. 6.4 mm c.…

A: Given:- The length of the fillet weld = 9 mm To determine:- The most nearly value of the throat

Q: If 100 mm leg of ISA 100 65 8mm angle is connected to the gusset plate as shown below with total…

Q: usescale (1/1) draw the front Section view in mides pan and the side Sectional Vien middles pan for…

A: Front Sectional View: The front sectional view is the view of the object done by taking a section…

Q: Determine the lengths of the side fillet welds required at the heel and toe of the angle shown.…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate Fy = 248 MPa Fu =…

Q: Using the elastic method, determine the maximum force to be resisted per inch by the fillet weld…

A: Consider the free body diagram as;

Q: Determine the required fillet weld size for the angle bracket shown per the given weld configuration…

A: Given weld configuration and it is required to determine the required fillet weld size for the angle…

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

Q: 4m 2KN/m 盒 2DKM am Draw free bedy diagram, Find the reections (Show cakulalion. Draw ascal…

A: We are authorized to answer three subparts at a time since you have not mentioned which question you…

Q: 6. What is the best suitable type of pipe? a) Hard b) Rigid c) Tough d) Malleable

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

Q: 20 find the required fillet welds size if the alloweble shearstress is (9.4kN/km²) forthe figure…

A: C.G of the weld on X axis x=190×95+190×95+250×0190+190+250=57.3 mmand on y axis y=2502=125…

Q: Problem 7: Locate the centroid y of the cross-sectional area of the beam constructed from a channel…

Q: Determine the required weld size necessary to carry the load P.

A: Solution Dead load(PDL)=360 kN Live load(PLL)=120 kN The centroid of the area is, x=1502=75…

Q: and L = ( 6.5 + 1.5b) inches. Determine the design strength oR, for the concentrically loaded weld…

A: Fillet weld: - It is defined as the process in which two metal pieces join together perpendicularly…

Q: nated wood beam giuing (actual dimensions) cross section, as shown int 12 in. 3 in. 2 in. 2 in. 2…

Q: Calculate the normal stress in the weld due to axial force of 40 kN. Consider throat thickness of…

A: Axial force (P) = 40kN = 40 X 103 N Thickness of the weld (t) = 4.2 mm Length of the weld (l) = 350…

Q: A supply plenum is fastened to the furnace with equally spaced screws. Findin inches dimension X.

A: Given values: A supply plenum is fastened to the furnace with equally spaced screws. Distance…

Q: The effective throat thickness of a fillet weld not to be greater than.... a. 0.3t b. 0.6t C. t d.…

A: Throat is the part of weld which is assumed to be effective in transferring the stress. Throat is…

Q: he allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the…

Q: using Draw S.P.D and B.M.D Virtual work Methol 6KN/M 20KN/ RI 2m R2 um

A: We have to draw the shear and bending moment diagram

Q: b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a…

A: Solution Given data Length of gusset plate L=140 mm Width of gusset plate b=320 mm

Q: 1-draw the net work using AOA method 2- draw the net work using AON method Activity Predecessor A --…

A: Network diagrams in project management are used to represent different activities and also their…

Q: mensions as shown is to be connected to a plate of the same width and thickness by standar ong the…

Q: The connection shown below is fastened by bolt is 100 MPa, determine the maximum ax

Q: Find CLR? () lb/ft3 (*No unit)

A: QRR = 100.0 ft3/sCRR = 0 lb/ft3QLR = 60.0 ft3/sCLR = ? lb/ft3Qout = 160.0 ft3/sCout = 150 g/L1 g/L =…

Q: The cylindrical portion of the compressed air tank shown is fabricated of 0.25-in.-thick plate…

A: Calculation of inner radius- r=d2-tr=102-0.5r=4.75 in

Q: 1. A 150 X 90 X 12 mm angular section is welded to a gusset plate shown. Area of angular section is…

A: The given figure is shown below:

Q: Provide a balanced welded connection to mobilize the full capacity of the angle. ( Filler material…

A: The values and figure(diagrame) given in the question are as follows Yield strength(fy)=480 MPa…

Q: The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the…

Concept explainers

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.

Question

Determine the maximum effective net area of the fillet weld using the maximum
weld allowed by the code. Length of 550 mm and a maximum weld size is 12.5
mm. *
P
10,601 sq.mm.
9721 sq.mm.
8840 sq.mm.
O 1100 sq.mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the lengths of the side fillet welds required at the heel and toe of the angle shown. Allowable shearing stress through the throat of each weld is 124 MPa. L 150 x 150 x 13 L1 P1 108 T= 250 kN 42 13 150 mm P2+ L2 gusset plate 150
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
Show min weld strength (kips/in) of the nominal size of the fillet weld from 1/8" to ¾” with SMAW. Explain the effective area of the welds.
Determine the effective area of the figure as shown. PL% x 5 Weld
Calculate the maximum shear force in the welds and the required weld size in the given figure. Where P= 50kN X=60mm, Y=150mm, Z=100mm What is the maximum force on the weld in kN/mm? (2 decimal places) What is the required weld size considering E70xx fillet weld in mm? (rounded value)
Calculate strength of single V butt joint to join 2 plates 300 x 16 mm with f = 250 MPa. Assume weld to be fabricated on field. (for single 5 V-butt weld, throat thickness .xtmin). 8 =
*Calculate the maximum allowable force "P" that can be applied without causing the weld to fail. Use the Elastic Method 24" 1/4/
2. Determine the lengths of the side fillet welds required at the heel and toe of the angle shown. Allowable shearing stress through the throat of each weld is 124 MPa. L 150 x 150 x 13 L1 P1 108 13 150 mm T= 250 kN P21 L2 gusset plate 150
If 100 mm leg of ISA 100 65 8mm angle is connected to the gusset plate as shown below with total weld length(Lw) of 290 mm. Calculate Lw1 and Lw2. Use steel table Lwl ISA 100 65 8 mm Lw2
20. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksit) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places)
Problem 2: What is the U value for these cases? 1. Plate connected using bolts (fasteners) only. 2. Plate using transverse welds only 3. 3/4 in thick plate using longitudinal welds only where the length of the weld (L=10 in) and L = 1.25 W where W is the width of the plate. 4. Single angle where both legs are bolted to the support. 5. Single angle L8x8x1 with longitudinal welds (L = 9 in) on one leg 6. Channel C10x20 connected using one bolt only in the web 7. Single angle connected on one leg using transverse and longitudinal welds.
Design calculations for a certain 1/2 in fillet weld show that the effective length required is 7 in. If allowance is made for defects at the ends of the weld, the actual length should be NOT less than A. 9 in. B. 8 1/2 in C.8 in. D. 7 1/2 in.