Consider the voltage source shown in the figure for w= 5 rad/s and w=15 rad/s. Let Vs = 15 cos (wt) V, R = 5 ohm, C= 0.1F, 4₁=1 H, and 4₂ = 2 H.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.Vs ±morL₁CRwww12 Determine the real and reactive power supplied by the source vs(t) 15 cos(5t) V.The real and reactive power supplied areVAR.W and

Answered: Image /qna-images/answer/6e1489df-c069-4aba-9bb0-12e3514aad51.jpg

Answered: Determine the real and reactive power…

Determine the real and reactive power supplied by the source vs(t) 15 cos(5t) V. The real and reactive power supplied are VAR. W and

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
2. Refer to the Figure 2. a) Determine the total impedance of the circuit in polar form. b) Determine the voltage v(t) and current i(t) sinusoidal forms. Sketch one cycle of the waveforms in the same x-axis. Clearly indicating the peak value and the period of each waveform and the phase difference (in milliseconds) between the two waveforms. c) Determine the values of resistance R and inductance L. d) Determine the phasors V,, VR and Vc. e) Sketch the phasor diagram showing Vs, Vr, Vr, Vc and I.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
H.W 2 An AC circuit includes two sections AB and BC in series. The section AB consists of two branches in parallel. The first of these is formed of resistance of 60 2 in series with a capacitor of 50 mF, while the second consists of a resistance of 60 2 having an inductance of 250 mH. The section BC consists of a resistance of 100 N having an inductance of 300 mH. The frequency of the current is 50 Hz. The voltage across section AB is 500 V. What is the voltage across the section BC?
You are working in an industrial plant. A bank of capacitors is to be used to correct the power factor of a 480-V, three-phase motor. The capacitor bank is connected in a wye. Each of the three capacitors is rated at 25 µF and 600 VDC. You have been told to reconnect these capacitors in delta. Can these capacitors be changed from wye to delta without harm to the capacitors?
Ererrises: IA platinum oil has a resifance of 3-14k r at go°C and 3.747JV at 100°C.- Fin'd the resistance at o'C ond the kmp -creff. of resifonce af 40°C 2. A pofential difference of r5oV is apphed to a field wnding at 15°C and the currend is SA. What will be the mean fempouafure of the winiding when currend has falen to 3.91A, apphedvrltage being constant Aasume s =p7.5. 3. A cril has a resi fance of 182 when its mean femperature is 20°C and 20v when ik mean femperature s 50°C. Frid is mean femperature rise when ik resotonce is 21JL and the sorrandinig femperature is i5°C. A cril of a relay takes a curre of 0.12 A when it is at the vem insbi o al 4. A jemperature of is'C ond canneckerdacms a oV supply If the minimum operating current of the relay is 0.1 A, colculate the femperature above ohich the relay will fail to operate when connected ti the same supply. Resi tncenfemp.coefficrenf of the cril makria] is o.0043 per °C at 0°C.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
A generator rated at 30MVA, 11kV has a reactance of 40%. Calculate its p.u. reactances for a base of 50MVA and 10kV. O 0.606 p.u. O 0.506 p.u. O 0.806 p.u. O 0.706 p.u.
If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit be? Explain why. a) a pure resistor circuit b) a series or parallel R-L circuit c) a series or parallel R-C circuit d) a series L-C circuit