Problem 4.5 Consider the split Russel traction device and amechanical model of the leg shown in Fig. 4.53. The leg isheld in the position shown by two weights that are connectedto the leg via two cables. The combined weight of the leg andthe cast is W = 300 N. / is the horizontal distance betweenpoints A andB where the cables are attached to the leg. PointCisthe center of gravity of the leg including the cast which isbelocated at a distance two-thirds of I as measured from point A.The angle cable 2 makes with the horizontal is measured asB3D45°.An.Ar9Type here to searchCcF5F1F2F3F4F6F7%23%2413r50WERTYlo41 Determine the tensions T1 and T, in the cables, weights W1and W, and angle a that cable 1 makes with the horizontal, sothat the leg remains in equilibrium at the position shown.Answers: T W, =223.6 N, T, =W2 = 282.8 N, a = 26.6°herce1CB BW2.26/3T2Tv11Fig. 4.53 Problem 4.5DeletePrtScInsertF12F11F10F9F8F7Backspa

Draw a free-body diagram of the given system. Apply equilibrium equation of forces in the…

Answered: Determine the tensions T1 and T, in the…

Determine the tensions T1 and T, in the cables, weights W1 and W2, and angle a that cable 1 makes with the horizontal, so that the leg remains in equilibrium at the position shown.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.189RP: The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find...

See similar textbooks

Related questions

Q: The object below is in equilibrium and has a weight w = 80 N. Find T,, T2, T3 and T,.

A: Free body diagram

Q: Determine the magnitude of F1 for equilibrium of the particle.

Q: Two forces F1 150 N and F2 50 N to hold the weight of 200 N. Check and determine if the body is in…

A: Equilibrium is a state of a body at which there is no disturbance in a system neither inside nor…

Q: FA 30° FB B 50 lb

A: Given Applied load = 50 To find FA FB Weight of the pipe

Q: Determine the tension in cables BA and BC necessary to support the 60 kg cylinder in the opposite…

A: Given data: Mass of the cylinder, m = 60 kg. Calculate the weight of the cylinder, W=mg=60 kg×9.81…

Q: If block D weighs 300 lb and block B weighs 275 lb. determine the required weight of block C and the…

A: Consider the free body diagram: For block D: T1=275 lbAngle between forces T1 and T2=αAngle between…

Q: Determine the force in each cable and the force F needed to hold the 10-lb lamp in the position…

Q: Determine the force in each cable needed to support the 20 kg flowerpot. B 6 m

Q: The 500-kg crate is supported by the three cables. Find the tension in cables AD, BD and CD.

Q: A puck weighs 10 lb and rests on the center of the frictionless surface of the ramp supported in…

Q: Determine the force in each cable needed to support the 200-lb construction beam.

A: Answer: Forces in cables- TCD = 256.126 lb , TAC = 87.55 lb and TBC = 87.55 lb

Q: The crate has a weight of 550 lb. Determine the force in each supporting cable.

A: Given data Weight = 550 lb

Q: Determine the tension at the cable TAB and TAC in the system below at equilibrium.

A: Calculate the inclination of the cable AB with the horizontal. θ=tan-13 m4 m ≈36.9° Here, θ is the…

Q: Each cord can sustain a maximum tension of 500 N. Determine the Force at cord AE.

A: Given, The maximum tension is 500N. Resolving forces at each end. At A: Free Body Diagram: ΣFY =…

Q: Determine the force in cable BA and BC needed to hold the 68-kg pipe.

Q: 6. The system below is fixed at A has a roller at C and contains a hinge at B. Determine the support…

Q: Q2: Determine the magnitude of vertical component of reactions (Cy and Ay) and the force in the…

Q: 05: The 50-kg homogeneous smooth sphere resèts on the two inclines. Determine the contact forces at…

Q: If in equilibrium, the anticlockwise turning effect of force F must equal the clockwise turning…

A: Calculate the force F by applying moment at the pin point as follows: ∑MO=0F×0.25=5×0.5F=10 N This…

Q: If cable CB is subjected to a tension that is twice that of cable CA, determine the angle 0 for the…

Q: force in each cable

Q: Determine the reactions at the support. There are two supports: a collar that can slide along the…

Q: If cable CB is subjected to a tension that is twice that of cable CA, determine the angle @ for…

A: Tension in CB = 2* Tension in CA

Q: Q2/ The truss gusset plate is subjected to the forces of three members. Determine the tension force…

Q: Determine the distance d for placement of the load P for equilibrium of the smooth bar in the…

Q: B C 8 ft 3 ft

A: The coordinates of different points is given below – The position vector of a different line as…

Q: Q (3): Determine the tension in AC and BC if two cables are tied together at C and loaded which has…

A: Given Data Mass of the load is: m=20 kg Angle at A is: α=50° Angle at B is: θ=25° Weight is,…

Q: Determine the force (F) which applied to ring A in order to keep the 250 lb *.cylinder B in…

A: As it is given that cylinder is in equilibrium, then the forces and moments acting on it are in…

Q: Q2. Determine the tension developed in each cord required for equilibrium of the 40 kg(F) and 30 kg…

A: Mass of F lamp = 40 kg Mass of G lamp = 30 kg

Q: 15 B

Q: The 1020-kg car is being lowered slowly onto the dock using the hoist A and winch C. Determine the…

A: Given data Mass of the car (M)=1020kg

Q: Determine the tension in cables BC in N necessary to support the 71-kg cylinder if the tension in…

Q: The window washers A and B support themselves and the 15-kg uniform plank CD by pulling down on the…

Q: The bar shown is in equilibrium determine the forces P, T and R

A: Given Load in the system To find Magnitude of P, T and R

Q: Determine the magnitude of the force P required to hold the 300-kg crate in equilibrium

Q: If the sack atA, has a weight of 40 lb, determine the weight of the sack at B and the force in each…

Q: The Shaft AB is supported by a thrust bearing at A and a slider bearing at B. Determine the force in…

Q: are joined at the junction ring C. Determine the tensions in cables AC and BC caused by the weight…

Q: A puck weighs 8 lb and rests on the center of the frictionless surface of the ramp supported in…

Q: Determine the stretch in each spring for for equilibrium of the 1.8-kg block. The springs are shown…

A: Mass (m) = 1.8 kg Spring constant AB = 30 N/m Spring constant AC = 20 N/m Spring constant AD = 40…

Q: i) Determine the range of the mass of block so that the system is in M =: equilibrium. M2 ii)…

Q: Determine the angle 0 at which the link ABC is held in equilibrium. The springs are unstretched when…

Q: If the maximum tension allowed in cable AD is 500 N, determine the tension in cables AB, AC, and the…

A: Given: F_AD = 500 N To find: F_AB = ? F_AC = ? W = ?

Q: 7. Determine the tension developed in cables AB, AC, and AD required for equilibrium of the 300-lb…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: Q/ Determine the horizontal and vertical components of reaction at the supports (A and B). Neglect…

Question

Problem 4.5 Consider the split Russel traction device and a
mechanical model of the leg shown in Fig. 4.53. The leg is
held in the position shown by two weights that are connected
to the leg via two cables. The combined weight of the leg and
the cast is W = 300 N. / is the horizontal distance between
points A andB where the cables are attached to the leg. Point
Cisthe center of gravity of the leg including the cast which is
be
located at a distance two-thirds of I as measured from point A.
The angle cable 2 makes with the horizontal is measured as
B3D45°.
An.
Ar
9Type here to search
Cc
F5
F1
F2
F3
F4
F6
F7
%23
%24
1
3r
50
W
E
R
T
Y
lo
41

Determine the tensions T1 and T, in the cables, weights W1
and W, and angle a that cable 1 makes with the horizontal, so
that the leg remains in equilibrium at the position shown.
Answers: T W, =223.6 N, T, =
W2 = 282.8 N, a = 26.6°
he
rce
1
CB B
W2
.
26/3
T2
Tv
11
Fig. 4.53 Problem 4.5
Delete
PrtSc
Insert
F12
F11
F10
F9
F8
F7
Backspa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The tongs shown are designed for lifting blocks of ice. If the weight of the ice block is W, find the horizontal force between the tongs and the ice block at C and D. Neglect the weights of the tongs.
Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
The center of gravity of the nonhomogeneous bar AB is located at G. Find the angle at which the bar will be in equilibrium if it is free to slide on the frictionless cylindrical surface.
A uniform 80.0 N ladder 4.0 m long is placed against a frictionless wall with its base situated 2.0 m from the wall. Find the forces exerted by the wall and by the ground on the ladder.
2. A solid consists of a cylinder and a hemisphere of equal radius fixed base to base. Find the ratio of the radius to the height of the cylinder, so that the solid has its centre of gravity at the common face. (Ans. 2:11 Hint. For stable equilibrium, the centre of the body should beelow the common face or maximum lie on it. So take the centre of gravity of the body at a distance (a) from the bottom of the hemisphere.
2. A uniform 80.0 N ladder 4.0 m long is placed against a frictionless wall with its base situated 2.0 m from the wall.Find the forces exerted by the wall and by the ground on the ladder.
In the position shown in Fig.4, the excavator applies a 20 kN force parallel to the ground. There are two hydraulic cylinders AC with effective diameter of 95 mm respectively to control the arm AB. Meanwhile, a single cylinder DE with effective diameter of 105 mm to control arm EBIF. Neglecting the weight of the members, determine the pressure against each of the piston for the hydraulic cylinders.
Figure is a simplified sketch of the mecha- nism used to raise the bucket of a bulldozer. The bucket and its contents weigh 10 kN and have a center of gravity at H. Arm ABCD has a weight of 2 kN and a center of grav- ity at B; arm DEFG has a weight of 1 kN and a center of gravity at E. The weight of the hydraulic cylinders can be ignored. Calculate the force in the horizontal cylinders CJ and El and all forces acting on arm DEFG for the position shown. 30°1, 30° 0.6 m 0.9 m 0.6 m 0.9 m 0.6 m 0.9 m 0.3 m
You must exert a force of 52 lb to support a load in a wheelbarrow such that the handles are parallel to the ground. Your hands are gripping the handles 3.1 ft from the axle. The load in the wheelbarrow is 144 lb. How far is the center-of-gravity of the load from the axle?
In Fig. the weight w is 60.0 N. (a) What is the tensionin the diagonal string? (b) Find the magnitudes of the horizontalforces F S1 and F S2 that must be applied to hold the system in the positionshown.
A non-uniform bar rests across two supports that are 20 ft apart. When loads of 200 lb, 4 ft from end A and 150 lb, 6 ft from end B, are on the bar, end A supports 233 lb and end B supports 197 lb. Find the weight of the bar and the position of the center of gravity.
A hoist lifts 525 kg of concrete. Calculate the weight of the concreate, that is the force exerted on the host by the concrete.