M8 A cantileveredbent beam which has a circularcross section with diameter of 0.3 m issubjected to a vertical downward force, P (kN)and a bending moment, 0.5P (kNm) directedas shown. The beam is made of brittlematerial with ultimate strength in tension equalto 350 MPa and compression equal to 330MPa At section a-a,a. Identify which point/s in the section (A, B, Cand/or D) should be considered as criticalpoints in the analysis for failure. State allpoints that apply and briefly explain why. Showyour complete solutionsb. Determine the value of P such that thematerial will not fail at any point using theMNST failure criterion.P (kN)0.5P (kNm)Section a-aBAIC0.45 mDIA

Answered: Image /qna-images/answer/acdb6cfe-c7c3-482b-b158-ff675f4b7ff9.jpg

Answered: Determine the value of P

Engineering

Civil Engineering

Determine the value of P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 15 The design shear resistance, Vpl.Rd of a fully restrained simply supported Universal Beam with yield strength 345 N/mm² is 1,285 kN A point load of magnitude 1,906 kN is applied at the beam's mid-span The area of the web of the beam is Aw = 5,505 mm² The plastic modulus is Wpl.y = 2,979 cm³ The thickness of the beam web is tw = 12.6 mm Find the reduced design moment of resistance of the beam Mc,Rd (use the formula for l-cross-sections with equal flanges and bending about the major axis) Give your answer in kNm to the nearest whole number. Do not include units in your answer.
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
FIGORE %3D aluminum [E = 70 GPa] links (1) and H.W.3: In Figure (2) support rigid beam ABC. Link (1) has a cross-sectional area of 300mm2, and link (2) has a cross-sectional area of 450 mm2. For an applied load of P = 55 kN, determine the rigid beam deflection tad Nadhon hub at point B. (2) 4,000 mm (1) 2,500 mm 1,400 mm 800 mm P. FIGURE
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
A cantilevered structural member is fabricated with the cross section shown below and is eccentrically loaded with F. - 26- F 2t F tt Use G = 77.2 GPa. If I = 4 m, t = 3 mm, b = 80 mm, and F = 112 kN, %3D Determine the maximum shear stress due to torsion. Select the correct response: 133.333 MPa 215.278 MPa 168.056 MPa 155.556 MPa
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Q3) The beam system has a pin support at A, roller supports at D and F, and internal hinges at C. Find the deformations at C and E using the conjugate beam method. 10 kN A C D E F 100 kN-m k5 mt-5 m--5 m5 m-k10 m- = 100 x 10° mm*, and ICF Given: E = 200 GPa, IAC 50 x 10° mm“. %3D لقطة شاشة
P2 - A rectangular beam has a design moment of 40 kNm. The material has a 200 MPa yield strength. Create a section with a width-to-depth ratio of 0.5 using the elastic and plastic theories, respectively.
3G “. Asiacell %99 Home Work... adhomShupper H.W. 1: 4.3 m Two axial members are used to support a load P applied at joint B. • Member (1) has a cross-sectional area of A = 3,080 mm2 and an allowabl normal stress of 180 MPa. • Member (2) has a cross-sectional area of Az = 4,650 mm2 and an allowable normal stress of 75 MPa. Determine the maximum load P that may be supported without exceeding either allowable normal stress. 5.0 m 2.0 m
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
The shown L-shape cantilver is loaded as shown and fixed at A. It has a constant section of 40 mm X 20 mm. For point I located at 50 mm from support A, at the midheight of the section, determine the principal stresses, the principal planes and the maximum shear stress. y 50 mm 150 mm 40 mm 0.5 kN H- I 20 mm 3 kN 160 mm 2.5 kN