Draw the 4-bit shift right register circuit implemented with JK type F/Fs. Since the circuit has serial data inputs (01101011), what will be the Q outputs of the F/Fs at the end of the 5.CLK? (F/F outputs are 0 at the first time, show each step in the table.)
Q: Explain multiplication of binary with block diagram and perform hardware implementation of 12 and 10
A: Binary Multiplication: There are two methods of binary multiplication, (i) paper method and (ii)…
Q: Design a 8 bits DAC and convert the following binary numbers to Analog 1- (10011101)2 = ? 2-…
A: DAC is a circuit which converts the digital input analog output.
Q: Initially Load 4-bit binary counter with 0111 and decrement this counter three times and show the…
A:
Q: 3 - Assume that a five-bit binary counter starts in state 00000b. What will your count be after 157…
A: The initial state of the counter is, 00000b The binary representation of the decimal number 157 is…
Q: If for 9bit ADC, VREF+=4V, VREF-=0 then 1.8V is binary encoded as: O a. 11100001 O b. 10011011 O.…
A:
Q: 32-Bit MIPS Register File Implement 32-Bit MIPS Register file (Zero Register...etc) CLK WE3 A1:…
A: Please find your answer below.
Q: If there is a digital bits wanted to be transmitted using all kinds of shift keying. Make a…
A: In digital communication, there are three digital modulation techniques and they are as follows ; 1.…
Q: S Display will be designed for a thermometer. The display will show that degree for minimum…
A: As per our policy we can provide solution of first three questions only. For a) As given, the…
Q: Input streams Output stream 11110000 11001100 H ???????? 10101010
A:
Q: Show how a five bit 11011 binary number can illustrated in the five-bit serial in –parallel out…
A:
Q: With a neat logic diagram and shifting table, explain the shifting of given bit stream 1011001…
A:
Q: Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit…
A: Truth table is, a b c A B V 0 0 0 X X 0 0 0 1 0 0 1 0 1 0 0 1 1 0 1 1 0 1 1 1 0 0 1 0 1…
Q: How to represent zero in 8-bit l's complement? a. 00000000, 1111111 O b. 00000000 O c. 1111111
A:
Q: Determine the decimal values of the signed binary numbers expressed in 1's complement a. 00010111 b.…
A: a) Determine the decimal values of 00010111:…
Q: Problem #1: 7-4. A binary ripple counter starts from 0 and counts up to 511. (a) What is the MOD…
A: The flip flops are used to store the data and act as memory elements. The counter circuits use the…
Q: Write a program to print out the binary equivalent of a positive integer value entered. [Reverse…
A: A program to print out the binary equivalent of a positive integer value entered is given below:…
Q: The signed binary number 0011011 is a positive binary number. Select one: O True False
A: As the left most bit is 0 so the given number is positive.
Q: We want to design a 4-line to 2-line priority encoder that encodes the four inputs Do, D1, D2, and…
A: Given a 4 bit priority encoder. D0 D1 D2 D3 =1 1 0 1 D0 : MSB D3 : LSB X: MSB Y : LSB
Q: Use contraction beginning with a 4-bit adder with carry out to design a 4-bit increment-by-3 circuit…
A: we will use 4-bit full adder for the circuit.
Q: a. Design 4-bit Parallel in Serial out (PISO) shift register.
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: Adders are digital circuits in electronics that implement addition of binary numbers. Given two…
A:
Q: A real analog signal x (t) is sampled at rate 64 samples/sec. A 512 point DFT is taken of these…
A: The Given real analog signal xt is sampled at rate 64 samples/sec.
Q: In the transmission of digital information, the proba- bility that a bit has high, moderate, or low…
A: Transmission of digital information
Q: The upper 16 -bit binary count value are displayed on the four seven -segemnt displays as four…
A: The DAC is an digital to analog convertor. The machines understand the digital binary bits in their…
Q: The binary string 11b10010111110 is a floating-point number expressed using the 14-bit simple model…
A: Given,Using the 14-bit simple model,The binary string in floating-point number is,X=11010010111110
Q: Implement the function f(w1, w2, w3) = m(0, 1, 3, 4, 6, 7) by using a 3-to-8 binary decoder and an…
A: Decoder: It is a combinational circuit which has n no of inputs and 2n no. of outputs. At a time, a…
Q: Using the De N TMS thTM convert the SOP Boolean equation: complement. What is the range of values…
A:
Q: What is the simplest equation to describe F(A,B,C,D), where F=1 when the binary value of the inputs…
A:
Q: Address Data ex8007 Ox79 ex8006 OXCD Өx8005 ӨХАЗ RO = 0x8000 and the memory data placement is as…
A: Given: R0=0x8000 and the memory data placement is as follows: To find: What is the order of r1 and…
Q: Refer to the following registers values and memory snippet to answer the following questions.…
A: The 8086 microprocessor is a 16 bit microprocessor with 16 data lines and 20 address lines. It is…
Q: Q1) Design a counter that has clk and rst as input and 4 bit output. The counter counts in the…
A: Present state Q3Q2Q1Q0 Next state Q3+ Q2+ Q1+ Q0+ Flip flop input D3 D2 D1 D0 0000 0011 0011…
Q: Q4) Starting from an initial value of R 11010101, determine the sequence of binary values in R after…
A: circular shift does not change the value of R . first we shift R logic left then in last logic right…
Q: Design a 4-bit magnitude comparators, which compares two 4-bits binary numbers (A3A2A1A0 and…
A: binary inputs A3 A2 A1 A0 Binary inputs B3 B2 B1 B0 Outputs A<BA>BA=B
Q: 4) Write a truth table for the function performed by the CMOS transistor. The truth table should…
A:
Q: Let the data stream 1001011101 to be the input sequence of a differential encoder. Assume that the…
A: Given: The data stream 1001011101 to be the input sequence of a differential encoder. Assume that…
Q: Find the output phase shift of the DPSK circuit given be V=A+B +1 The input data are (111010011010),…
A: Given input data : 111010011010 Initial value of shift register is high logic
Q: )Design Binary Ripple Counter using D-flipflop. ) Design asynchronous 4-bit UP-Down counter.
A: As there are two questions and it is not mentioned which question to do. So, please mention the…
Q: The values of A and B as 4 bit binary number and the value of M has been given regarding to…
A: Given: A3A2A1A01000 and B3B2B1B01001.
Q: 4.10 Design a four-bit combinational circuit 2's complementer. (The output generates the 2's…
A: According to our policy we can only solve one. As you haven't mentioned which one is required so I'm…
Q: a. What is the counting range in binary and decimal for an up-counter with 3 bits? p. What is the…
A:
Q: 8085 microprocessor went through its manipulation operation in the ALU, the results was transferred…
A: 8085 is an 8-bit microprocessor which is designed in 1977 by intel using NMOS technology. The 8085…
Q: Sketch a timing diagram of a 4-bit binary counter like the 74X163 showing the clock signal CLK and…
A: Sketch a timing diagram of a 4-bit binary counter like the 74X163 showing the clock signal CLK and…
Q: What is the binary representation of whole number 1,234 as a 12-bit signed integer? What is the…
A: In 12-bit signed integer, MSB is use to represent sign and rest of 11 bits are used to represent the…
Q: Q4\ design synchronous counter with irregular binary count sequence shown in below using negative…
A: Design synchronous counter with irregular binary count sequenc shown in below using negative edge,…
Q: Problem 10. A comparator shown in the circuit below is used to pick the larger of the two 4-bit…
A: (a) Write the truth table for the 4-bit-2-to-1 MUX as below. Inputs Outputs G S Y3…
Q: (a) If I have an n-bit unsigned integer, is it correct to say that I can always represent it as an…
A:
Q: B- A- B-[ A B -Y -Y AHC AH A B- B (a) 1. Write a truth table for the function performed by the gate…
A: The answer of the following question is
Please write nicely.
Draw the 4-bit shift right register circuit implemented with JK type F/Fs. Since the circuit has serial data inputs (01101011), what will be the Q outputs of the F/Fs at the end of the 5.CLK? (F/F outputs are 0 at the first time, show each step in the table.)
Step by step
Solved in 3 steps with 1 images
- The 3-bit shift register is shifted five times to the right with the serial input being 1011101. What is the content of the register? (Write your answer using only 0s and/or 1s.)After the data have been entered into the register in Figure, what will be the values stored in Q3,Q2,Q1,Q0 respectively A.1,0,1,0 B.1,1,0,1 C.0,1,0,1 D.1,0,0,1Q1. Show the implementation of 4 bit binary to gray code (shown in below table) converter using either EPROM or PLA. In Gray code only one bit changes at a time. Binary Gray code Decimal equivalent 0000 0000 1 0001 0001 0010 0011 3 0011 0010 4 0100 0110 5 0101 0111 6. 0110 0101 7 0111 0100 8. 1000 1100 1001 1101 10 1010 1111 11 1011 1110 12 1100 1010 13 1101 1011 14 1110 1001 15 1111 1000
- Q2) Convert to decimal number: 1) The hexadecimal number (FD45) 2) The octal number (7024) 3) The EX-3 (11001010.00110110) 4) The number of base 9 (8301)1. Assume that the registers are 8-bit wide. Consider the following code: MOV R1, #4A MOV R2, #40 ADD R3, R1, R2 a) What will be the 8-bit result in Register R3 (in hex)? b) What is the 8-bit result in Register R3 (as unsigned decimal)? c) What is the 8-bit result in Register R3 (as signed decimal)? d) What will be the value of the carry (C) bit?H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
- (c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit position of the first 1' in the pattern reading from MSB (2nd position) to LSB (0th position).An additional output variable V is required along with binary code to indicate that the binary code is valid or note i.e., if the input pattern is '000' then the output V should be '0' to indicate that the binary code is not indicating the bit position of first 1' and we don't care about the binary code if V = 0. Design the required circuit using dual 4x1 MUXS and minimum additional logic.Available resources along with dual 4x1 MUXS are NOT gates, 2-input(AND, OR, NAND, NOR) gates.Below is a 4-bit up-counter. What is the largest number of the counter if the initial state Q 3 Q 2 Q1Q0 =0011? (D 3 an Q 3 are MSB, and when Load = 1 and Count =1 the counter is loaded with the value D 3 ...D0) 4-bit counter Clock Q3 Load Count "I" or Vcc "I" or Vcc Do "1" or Vcc - D, Qi Q2 "0" or Gnd - D2 "0" or Gnd D3 Q3 1111 0011 1100 0110
- Write program to load the content of memory location 0x0700 into register R3 then set D6,D7 and complement D4,D5 for date in R3 then store the result in memory location 0x0800 .please show work included 4. If a 6-bit binary number is used to represent an analog value in the range from -63 to 126, what is the accuracy of the system? In other words, if the binary number is incremented by one, how much change does it represent in the analog value?Q4) Design a Register File which includes four 2-bit registers (In total, it includes 8 bits). Each register is named as ala0, b1b0, c2c0, d1d0. Registers are loaded from the S input. In addition to that, there are two input signals, X and Y, to determine which register to select (ie. 00 selectsfirst register ala0 etc). Also there is R signal. When W is zero, the content of the register does not change. When the W is 1 the selected register is loaded with a new value by shifting from the S input. Design this register file by using D flip-flops.