Draw the circuit diagram that represents the circuit 3. Using a constant 4.5 V source, three bulbs, wires, and a single throw switch design a circuit that will satisfy the following conditions, -When the switch is open (off) all bulbs are off -When the switch is closed (on) all bulbs are on -If one bulb is loosened (goes out) all bulbs go out

Draw the circuit diagram that represents the circuit 3. Using a constant 4.5 V source, three bulbs, wires, and a single throw switch design a circuit that will satisfy the following conditions, -When the switch is open (off) all bulbs are off -When the switch is closed (on) all bulbs are on -If one bulb is loosened (goes out) all bulbs go out

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter14: Troubleshooting Electric Control Devices

Section: Chapter Questions

Problem 32RQ

See similar textbooks

Similar questions

When you connect a voltmeter to read a dc voltage a. polarity is not important b. connect the voltmeter in series with the circuit c. connect the voltmeter across the component d. connect the common meter lead to the most positive point in the circuit
Using the black box from below, construct a circuit that fulfills the following objectives: Volage in point A: 500mV Voltage in point B: 1000mV
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本
When the switch is open, what is the: a. Total resistance b. Total power and c. V1
R1 of 90 kilo ohm and R2 of 10 kilo ohm are in series across a 43-volt source. A) Draw the schematic diagram. B) What is the voltage drop at R2?
We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SLIDE SWITCH: LEFT- OFF MIDDLE- DC VVOLTS DC mA NUMERICAL VALUE OF VOLTS OR MA OR OHMS DISPLAYED HERE 0.00 OHMS FIGHT - AC VOLTS AC mA OFFOO AC DC-n DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS (SELECT RANGE) 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 20 200 2K 20K. 200 200K 2M 20M MOVE ROTARY SWITCH TO THIS AREA TO READ mA (SELECT RANGE) *20u 200u 200m 20m 10A mA COM PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin NOT CONNECTED
If PMMC meter have internal resistance of 1002 and full-scale range of 1mA. Assume we wish to increase the meter range to 2A. the value of shunt resistor will be: OR_sh=0.00500 OR_sh= 0.00010 OR_sh=0.11111 0
A row of five lights is controlled by five switches. Each switch changes the state (on or off) of the light directly above it and the states of the lights immediately adjacent to the left and right. For example, if the first and third lights are on, as in Figure (a), then pushing switch A changes the state of the system to that shown in Figure (b). Ifwe next push switch C, then the result is the state shown in Figure (c).Suppose that initially all the lights are off. Can we push the switches in some order so that only the first, third, and fifth lights will be on? Can we push the switches in some order so that only the first light will be on?
A row of five lights is controlled by five switches. Each switch changes the state (on or off) of the light directly above it and the states of the lights immediately adjacent to the left and right. For example, if the first and third lights are on, as in Figure (a), then pushing switch A changes the state of the system to that shown in Figure (b). Ifwe next push switch C, then the result is the state shown in Figure (c). Suppose that initially all the lights are off. Can we push the switches in some order so that only the first, third, and fifth lights will be on? Can we push the switches in some order so that only the first light will be on?(a) suppose all the lights are initially off. Can we push the switches in some order so that only the second and fourth lights will be on? (b) Can we push the switches in some order so that only the second light will be on?
For the Turn ON voltage of different LED's refer Table 1. Table 1 Type of LED Red LED Turn On voltage 1.83V Blue LED 3.45V 2.13V Green LED Yellow LED 1.83V Orange LED 1.83V ii) For the circuit shown in Figure 8, Find a. current through LEDI b. current through LED2 LED1 LED3 R1 1kO Orange LED LED2 30mA Orange LED V1 R2 R3 2ko 1ka Blue LED Figure 8
All the lamps from Lamp #1 to Lamp #7 are designed to work with a nominal Voltage Vlamp of 120V and their resistance Rlamp is constant and do not depends on the temperature. Using this information solve the questions below. What is the maximum value of the variable ALPHA that will allow the channel 2 produce its maximum light output?
5. Draw the circuit diagram that represents the circuit. Using a constant 4.5 V source, three bulbs, wires, and a single throw switch design a circuit that will satisfy the following conditions - When the switch is open (off) one of the bulbs (bulb A) will be on and the others (bulb B and bulb C) are off - When the switch is closed (on) all bulbs are on - If bulb A is loosened (goes out); the others remain on - If bulb B is loosened (goes out); bulb C goes out and bulb A remains on - If bulb C is loosened (goes out); bulb B goes out and bulb A remains on