I need help on this question For the circuit in Fig 3.(a) Find the total impedance ZT in polar form.ZT = 8.94Ω∠26.57° (b) Find the voltage E and the current IR and IL in phasor form.E = 17.88V∠26.57°IR = 1.789A∠26.57°IL = 894mAV∠0°(c) Draw the phasor diagram of the voltages Is, IR , and IL, and the voltage E.Can you check if I make a mistake on these questions E+1I₁ = 2AZ0°R 10 ΩFigure 3:XL20 Ω is,c) Draw the phasor diagram of the voltage IS, IRIand IL and the voltage EjIL26,570ILISE+

Some basic conversions:Except the inductor current value IL, you got all the correct values.

Answered: E +1 I₁ = 2AZ0° R 10 Ω Figure 3: XL 20…

E +1 I₁ = 2AZ0° R 10 Ω Figure 3: XL 20 Ω is, c) Draw the phasor diagram of the voltage IS, IRI and IL and the voltage E j IL 26,570 IL IS E +

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 2PP: The circuit is connected to a 400-Hz line with an applied voltage of 35.678 V. The resistor has a...

See similar textbooks

Related questions

Q: 5.60 The op amp in the adder-subtractor circuit shown in Fig. P5.30 is ideal. PSPICE MULTISIM a)…

Q: See the incorrect and show all work Select the phasor corresponding to the following signal. i(t)…

Q: Please answer in typing format

A: identify the color bands on the carbonic resistor. Typically, a carbonic resistor will have four or…

Q: See Figure 11.8 below. If R = 30 2 and XL = 12 £2, what is the value of the total impedance? + R ww…

A: Thank you

Q: A heater, represented as a purely resistive element, dissipates 1000 Watts of heat when connected…

Q: a circuit that has two 2-bit unsigned integers X=x1x0 and Y=y1y0 as input. The circuit provides two…

A: The circuit you described has two 2-bit unsigned integer inputs, X and Y, and it provides two…

Q: Consider a piece of infinitely long semiconductor sample shown in Fig. 4-50. bbbbb Light FIGURE 4-50…

A: Step 1: Step 2: Step 3: Step 4:

Q: b. For the circuit shown in Figure 2, the switch is opened at t = 0 after being closed for an…

A: KIRCHHOFFS CURRENT LAW: It states that the algebraic sum of currents entering into the node is…

Q: Subject: Digital electronics Plz solve this Question

A: Step 1:Step 2:

Q: Please, help with this problem related to antennas. Do not use AI for answering. I need a real human…

A: Step 1:Step 2: Step 3: Step 4:

Q: Please answer in typing format

A: Given that,Speed of mobile station = 50m/sFrequency of transmission = 1.5GHz=1.5∗109HzDoppler spread…

Q: 5.23 The op amp in the circuit of Fig. P5.23 is ideal. PSPICE a) What op amp circuit configuration…

Q: A 208-V, three-phase, Y-connected, synchronous motor takes 7.2 kW at0.8 pf leading. The synchronous…

A: Step 1:Step 2:Step 3:

Q: Question 10 could you show work

A: To determine which sinusoid leads and by how much, we need to compare their phase angles. The phase…

Q: 1 a) A function g[n] is defined by -2 n≤-4 n -4≤ n ≤1 g[n] 4 1≤n n Calculate the signal g[2 – n] and…

A: Step 1:Step 2: Step 3: Step 4:

Q: CS Scanned with CamScanner 3. A steel ring, having a mean circumference of 750 mm and a…

Q: Use the equations (1) to (5) to find the value for R1 AND R2. = tc 0.693(R1 R2)(C1) .(1) td =…

A: Let's start by calculating the values of R1 and R2 for f=15 kHz.Given:Duty cycle D=0.7Frequency f=15…

Q: This is a practice question from my Introduction to Electronics course. Could you please walk me…

A: We have two branches to consider. D2 branchD3, D4, D5 branchFor input = 0 VAssume current flows…

Q: Say I have this circuit. How would I use KCL or KVL to find the values of 1.6 A going to the right…

Q: Q4: Using one OpAmp, design a summing/subtracting circuit with four inputs and one output as…

A: Step 1: In this problem, there are 4 inputs- two with positive and two with negative gains. Firstly…

Q: what is the transfer function of this, P(s) = K / (s(tau*s+1))

A: If you are having doubt in any step please comment here. Thank you

Q: explain each step and show how to get to this answer please i do not undestand

A: The image you sent, it appears to be a circuit diagram with a voltage source (V1), resistors (R1,…

Q: 1 H 4. In the circuit below, is₁(t) = 2 cos(t + 60°) A and is¿(t) = 3 A. 1 F HH 1Ω w 5 is 1 H ww 1Ω…

A: Step 1:Step 2:Step 3:

Q: Solve and show illustration A 20-kW 127.4 -V separately excited dc machine is operated at a…

A: Step 1:

Q: Q3: Calculate the convolution for the following tow functions f(t) & x(t)? f(t) 2 |x(t)=(-1)x(1) 0 1…

A: The convolution of f(t) and x(t), denoted by f(t) * x(t), describes how the shape of f(t) slides and…

Q: Please answer in typing format

A: 4 ohm and 2 ohm are series = 6 ohm10 ohm and 6 ohm = 16 ohm6 ohm and 16 ohm are parallel =…

Q: P7.1. Solutions for line voltage and current for an open-circuited line. For a line open- circuited…

A: Step 1: Step 2: Step 3:

Q: If x(t) = 1 for 0 < t ≤ 1, = exp(-t) for 1 <t≤ 2, and 0 elsewhere, plot and find the analytic…

A: Let's start by plotting the given piecewise function x(t) :x(t) = ⎩⎪⎪⎨⎪⎪⎧1exp(−t)0for 0<t≤1for…

Q: Q2 Find the transfer function of the system whose the Bode plot shown in figure below |GH(jo)| 80 db…

Q: 1. A 690-V, six-pole A-connected induction motor runs at 1085 rpm when operating at a full load.…

A: Sure, The information provided in the image is for a different motor with a voltage rating of 690…

Q: Refer to this figure. What is the imaginary component of the current in the circuit in amperes? what…

A: Thank You

Q: 1.- Considering two elements in series where: v = 500 sin (250 t -40°) volts I= 25 sin (250t - 90°)…

Q: A shunt-wound motor has a field resistance of 350 Ω and an armature resistance of 0.2 Ω and runs off…

A: Step 1: Circuit diagram:Step 2:Step 3:

Q: c. Falling edge-triggered D flip-flop. Clk D Q D Clk A D 0

Q: Please answer in typing format

Q: Q3: A plant has a nominal model given by G(s) = 1 S(S+1)(1+2s) assume that this plant is to be…

A: Step 1: Step 2: IF YOU HAVE ANY DOUBT YOU CAN COMMENT HERE THANKS

Q: Determine the voltage between the open bridge terminals A and B in the figure

A: KIRCHHOFFS CURRENT LAW: It states that the algebraic sum of currents entering into the node is…

Q: A balanced three-phase load consists of three coils, each of resistance 4 Ω and inductance 0.02 H.…

Q: Why should we unplug our electronic devices to conserve energy?

A: The objective of the question is to understand the reason behind the need to unplug electronic…

Q: Please answer in typing format

A: Step 1:To determine the secondary voltage at full load for a lagging power factor of 0.95, we'll…

Q: I want to solve this question with a clear white paper and thank you.

Q: For a 208 V three-phase balanced system shown below. Find:1) The line current iL.2) The voltages vAN…

A: Step 1: current IL IL=ZL+ZϕVan IL=0.06+j0.12+12+j9120∠0 IL=12.06+j9.12120∠0…

Q: 2. In a 30-km span, 3-phase line, calculate the per-phase resistance at 50°C, inductive reactance…

A: Step 1:Step 2:Step 3:Step 4:

Q: B-6-4. Show that the root loci for a control system with K (s² + 6s+ 10) G (s) = s² + 2s + 10 H (s)…

A: Step 1:Step 2:

Q: me: JASTINE P. MABUTOL Long Examination in AC Apparatus Date: APRIL 23 Score: Tections: Solve the…

A: Step 1:Step 2:Step 3:Step 4:Step 5:Step 6:

Q: For this op amp, an equation needs to be made for V0 = Va + Vb. I thought it was -4(Va) + 4(Vb) as…

A: We can use super position theorem to solve the equation.Va aloneShort circuit Vb.Now circuit become…

Q: Please answer in typing format

A: Step 1:When the generator is at no load means Ia=0The equation of generator is E=V+IaRaSo at no load…

Q: Discuss in detail about nodal analysis. Please answer in typing and not AI generated please

A: STEP 1 : Definition:Nodal analysis: This method used for calculate voltage between circuit nodes.In…

Q: What is the total impedance of a capacitor with a reactance 150 Ωwhenconnected to the following?a.…

A: The objective of this question is to calculate the total impedance of a capacitor with a reactance…

Q: Please answer in typing format

A: Given that, x=0;y=0;0≤z≤10According to biot savarts law,H=4πRI(sinθ1+sinθ2)Current I=2A Let OPQ…

Question

I need help on this question

For the circuit in Fig 3.

(a) Find the total impedance ZT in polar form.

Z_T = 8.94Ω∠26.57°

(b) Find the voltage E and the current IR and IL in phasor form.

E = 17.88V∠26.57°

IR = 1.789A∠26.57°

IL = 894mAV∠0°

Can you check if I make a mistake on these questions

E
+1
I₁ = 2AZ0°
R 10 Ω
Figure 3:
XL
20 Ω

is,
c) Draw the phasor diagram of the voltage IS, IRI
and IL and the voltage E
j
IL
26,570
IL
IS
E
+

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

1. What is the dielectric?
The circuit is connected to a 400-Hz line with an applied voltage of 35.678 V. The resistor has a true power of 14.4 W. and there are 12.96 inductive VARs and 28.8 capacitive VARs. ET35.678VITZVAPFERIRRP14.4WELILXLVARsL12.96LECICXCVARsC28.8C
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
The signals on the oscilloscope V1(t) and V2(t) are given as V1(t) = 300*sin(120 π *t + 30) , 2 V (t) = A*cos(120 π *t + B) in Figure-1. a) Determine the values of A and B.
What is the value of the voltage function at 12 seconds? v(t) = 87 sin (17πt + (5π/4) V
Given Ra= 2 ohm and Ih = 2A Find Vth and Rth
A voltage v = 300 sin (377t + 600) is applied across a circuit with pure element and draws a current of i = 7.0 sin (377t - 300) Amperes. Determine the value of the element of the circuit.
Answer: v(t) = (30/37)e-t/2 + (30/37)*cos(3t) + (180/37)*sin(3t) volt where t is in seconds
Calculate the angle when V=15kV v=7.26*10^-7m/s B=2mT x=45mm
The voltage across a 100 mH coil is v = 100 sin 50t. Which of these expressions describesthe current? 2) _____A) 20 sin 50tB) 20 sin(50t - 90°)C) 2000 sin(50t - 90°)D) 20 sin(50t + 90°)
Find the total/resultant effective voltage, given the following: e1 = 10 sin ωt e2 = -15 cos (ωt – π/3) e3 = 10 cos ωt e4 = -20 sin (ωt– π/3)
The admittance of a network is (0.05– j0.08) S. Determine the values of resistance andreactance in the circuit if they are connected (a) in series, (b) in parallel.