E (b.) (c.) A fictitious glass is consistent with data provided below. Table 1. Temperature (°C) 700 900 1100 Viscosity (P-poise) 1.09 x 10¹ Plot the data points from Table 1 in the figure above the table to show that it seems to "fit" the trends shown by the other glasses. Add an approximate trend line. 1.23 x 10 1.00 x 10 Viscosity (n) is the inverse of fluidity (p), where the latter obeys an Arrhenius formula: Therefore, viscosity obeys the following: p = A exp 1 exp(-27) RT n=no expl (Quiscous RT Determine the activation energy for viscous flow (Qviscous) for the fictitious glass. The glass-transition temperature is above the strain point, and this temperature is the lower limit of the supercooled liquid regime. The strain point in general is the temperature at which the viscosity equals 3 x 10¹4 P. What is the temperature of the strain point for our fictitious glass?

E (b.) (c.) A fictitious glass is consistent with data provided below. Table 1. Temperature (°C) 700 900 1100 Viscosity (P-poise) 1.09 x 10¹ Plot the data points from Table 1 in the figure above the table to show that it seems to "fit" the trends shown by the other glasses. Add an approximate trend line. 1.23 x 10 1.00 x 10 Viscosity (n) is the inverse of fluidity (p), where the latter obeys an Arrhenius formula: Therefore, viscosity obeys the following: p = A exp 1 exp(-27) RT n=no expl (Quiscous RT Determine the activation energy for viscous flow (Qviscous) for the fictitious glass. The glass-transition temperature is above the strain point, and this temperature is the lower limit of the supercooled liquid regime. The strain point in general is the temperature at which the viscosity equals 3 x 10¹4 P. What is the temperature of the strain point for our fictitious glass?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If the viscosity of SCl2 gaseous molecule at 20.0 °C and 1 atm. is 132 pP. what is the viscosity of 7cz gaseous molecule in pP at the same temperature and pressure assuming both molecules having the same cross section? (MM of 35c - 35.0g mol MM of 37a - 37.0 g mol1)
Question 4 Viscosity. From studies of the flow of neutrophils in micropipets, it is possible to measure the apparent viscosity of the cytoplasm. From the data below, do you think the cytoplasm is Newtonian? If not, determine the rheological relationship that best describes the behavior of the cytoplasmic viscosity Shear rate (s1) Apparent Viscosity (Pa s) 450 0.111 1 137 2.70 97 5.75 58 7 58
3. Shell T46 industrial lube oil has a viscosity of about 46.5cSt. What is its viscosity in terms absolute viscosity? Density if the oil is 804kg/m3. TNO L-Warning Oil Condition Viscosity 40 C Viscosity @ 100 t D-445 46.5 45.5 45.0 44.3 <39.87 D-445 CSt 7.0 6.9 6.9 6.8 <6.12 Oxidation E-2412 Abs 3.8 4.1 3.8 3.7 Nitration E-2412 Abs 2.6 2.6 0.04 2.6 0.04 2.6 0.11 TAN ng KONg 0.06 D-974 D-4739 ngKOH TBN
Choose each of the statements below that is/are false regarding viscosity. Justify why the statements you circle are false. (a) Viscosity is the resistance of a uid to shear.(b) The higher the viscosity, the less a uid resists ow. (c) In laminar ow, the uid moves in parallel layers. (d) Viscosity increases as temperature increases. (e) All of the above are true.
In the appendices, the modulus of elasticity for silicon nitride is 304 GPa (that of steel is 207 GPa). How much porosity could be present in the round bar of silicon nitride such that it equals the reported value for steel?
LAL 12 The density of a solid is its mass divided by its volume. If the less is measured as 42.5 ± 0.5 g and the volume as 54 ± 1 cm³, what it be the worst possible error in the calculated density?
A new sintering regime is proposed for producing Alumina acetabular liners for total hip replacement. If the alumina has a plane strain fracture toughness of 2.7 MPa.mº.5, an ultimate tensile strength of 307 MPa and Y is assumed to be 1.2, which of the following would be the maximum acceptable size of surfac flaw? Select one: O a. 4.8 um O b. 19.2 μm O c. 2.4 μm O d. 9.6 μm
O e. A zero tension is developed when no overlap betWeen actin and myosin The constitutive equation for blood shows that the shear stress is related to: O a. Shear strain rate O b. Yield stress O c. Viscosity O d. All of these TOSHIB
PLEASE ANSWER THEM ALL FOR AN UPVOTE. THANK YOU. Given: Pi constant to be used: 3.14159 Capillary tube: radius = 0.02 cm; length = 9 cm; pressure = 0.7 mmHg Liquid sample: density = 4 ml; time of flow = 4.5 seconds Ans. the ff questions. •What is the pressure in MKS unit? •What is the pressure in CGS unit? •What is the viscosity of the liquid? • If the weight was given as 8.5 grams, what will be the density of the liquid? •What is the kinematic viscosity of the liquid? •What is the fluidity of the liquid?
zain 1Q 2G 3G zain IQ Z Questions of Lectu... -> Questions of Lecture Four: Q1)) Answer the following briefly: What is means of Crystal structure? What the different between crystalline and amorphous structures? List the common lattice structures and give two examples for each? What the means of imperfections (defects) in the material crystals and why it happen? What are the differences between crystals imperfections types? How metallic crystals can deform elastically and plastically? Q2)) Fill the following blanks: A) Crystal structure can be found as -------- and ----------. B) Metals lattice structures are divide to -----, C) The three kinds of crystals imperfections can arise are --------, ---------, ----- Q3) Draw the following Point defects of crystals: (a) Vacancy, (b) ion-pair vacancy (Schottky), (c) interstitially, (d) displaced ion (Frenkel).
A core was mounted in a gas permeameter to measure permeability. Determine the liquid permeability (mD) of the core using gas (in oilfield units). The laboratory data are as follows: Diameter of the core = 3.78 cm Length of the core = 7.63 cm Gas viscosity = 0.0148 cP Flow rate = 9.07 cm3/s P1 = 1.439 atm P2 = 1.086 atm
6. Answer the following questions regarding the Lever Rule. [ a. Describe the purpose of the Lever Rule and write the equation. b. Using the lever rule for 52 wt% Zn-48 wt% Cu, cite the phases present and mass fractions at the following temperatures: 1000°C, 800°C, 500°C, and 300°C. Refer to the Cu-Zn diagram from problem 3 or use the book diagram on p. 326. 7. Returning to the Zn-Cu phase diagram, using the composition 52 wt% Zn-48 wt% Cu, draw schematics of the microstructures if you were to undergo a slow cooling process. Draw representations for 950°C, 860°C, 800°C, and 600°C. Make sure to properly label each phase and determine their approximate compositions.