eter is A petroleum product is pumped at a rate of 2.32 x 10'm/s from a reservoir under atniospheric pressure to 177 cm height. If the pump 132 cm height from the reservoir, the discharge pipe diameter is 3.8 cm and the pressure drop along its length is 3.5 kPa. The gauge pressure reading at the end of the discharge pipe is 351 kPa. The pressure drop along suction pipe is 3.45 kPa and pump efficiency n-0.73 calculate:- The total Ah of the system. The power required for pump. The NPSH Take that: the density of this petroleum product p-830 kg/ms, the dynamic viscosity u-6.47 x 10 Pa.s, and the vapor pressure Pv= 23.55 kPa.

eter is A petroleum product is pumped at a rate of 2.32 x 10'm/s from a reservoir under atniospheric pressure to 177 cm height. If the pump 132 cm height from the reservoir, the discharge pipe diameter is 3.8 cm and the pressure drop along its length is 3.5 kPa. The gauge pressure reading at the end of the discharge pipe is 351 kPa. The pressure drop along suction pipe is 3.45 kPa and pump efficiency n-0.73 calculate:- The total Ah of the system. The power required for pump. The NPSH Take that: the density of this petroleum product p-830 kg/ms, the dynamic viscosity u-6.47 x 10 Pa.s, and the vapor pressure Pv= 23.55 kPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At the gasoline transfer facility (ρᵣₑₗ=0,75) from the pond of storage to consumption, you want to install a pump to circulate a flow of 40(lt/s). The 400m long pipe is cast iron 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 2,9 (kgf/cm²) gauge pressure. Decide the drive power of the pump in KW if its performance is 70%. •Additional data, pressure drop factors: •Retention valve Kᵣ = 1,5 •Gate valve open Kᵥ = 0,21 •Medium Radius Commercial Elbow Kc = 0,75 for each cubit •Storage pond outlet sharp angles Kₛ = 0,5 •Entrance to consumption pond Kₑ = 1 •Friction factor in pipes f = 0.026
Water (p = 1000 kg m3'H= 10-3 R) flows in a horizontal constant-area pipe; the pipe cross ms 1. section area of 0.1 m?. At the pipe inlet, a pump is installed and at the outlet, the pressure is atmospheric. Determine the pump power when the pipe length is 10 meter and a. When the velocity is 0.01 m/s b. When the velocity is 0.1 m/s and the pipe is smooth When the velocity is 0.1 m/s and the pipe equivalent roughness is 0.1 mm (you may use Moody chart here) d. When the pipe is smooth and vertical and the velocity is 0.1 m/s С.
plzzzz help me with this one plzzz Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate of 0.2 m3/s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.44%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.
This is a fluid machine question. Water reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 98.08 kPa is maintained in the summit water discharge is 30 m above the reservoir. The quantity pumped is 0.50 m3/s. rrictional losses in the discharge and suction pipe of the pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm, what amount of energy must be furnished by the pump in kW?
A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
A pump receives water from a tank. If the pump needs 24 m of NPSHA, how high must the water level be above the pump centerline if the water is saturated at 1724 kPag? The friction loss in the pipe averages 0.3 m for each 6 m of height and flow is 23 lps in a 15.24 cm ID pipe.
We have a tank (large enough to neglect the velocity of the fluid surface in the tank v1 =0). The tank contains water at a mevel of 15 meters. The tank is enclosed and the air space above the water is at 5 atm. The exit of the tank consists of 25 meters of 2 cm diamter pipe with d/D = 0.0004. It exhaust to the atmospere at 1 atm. What is the exit velocity?
The water temperature in the tank is 60 °C and the pump has the capacity of 20 ton/hour. Pump is 2m below the bottom of the tank. Diameter of the pipe is 20 cm and the total length of the pipe is 10 m. The pipe is smooth (roughness of the pipe is zero). In the suction line, there are one sharp exit (Kı=0.6), one valve (KL = 17.5) and one 90° elbow (K1=0.3). The required NPSH is given as NPSHrequired=4+3.1050? (V unit in this equation is mº/s). What can be the minimum height of the water in tank (h) so that the pump can work without the cavitation (Patm=101.3 kPa, a=1.05)
A pipe of diameter 14 cm, is used to pump the water to the house in the Hamra hill at the height of 80 m than the ground. The discharge at the end of the pipe is 140 lit/s. The pressure gauge is fitted at the entry of the pipe in the ground is 34 N/cm. Find the following: O The velocity head at the entry of pipe (in m) (m Pressure head at the inlet (in m) (m) Total available energy per unit weight of the water at the pipe inlet (unit in m) (Enter only the values by referring to the units given in brackets & DO NOT write the unit & do not send the handwritten answers to my mail id.) velocity head at the entry of the pipe is = (unit in m) pressure head at inlet = (unit in m) Total available energy per unit weight of the water at inlet of the pipe (unit in m)
PRELIMS DISCUSSION IN ME 3214 FLUID MACHINERY PROBLEM: A 90-cm ID pipeline (f = 0.020) of length 3000 m connects a reservoir whose water surface elevation is 540 m to a nozzle at elevation of 300m. The jet from the nozzle is used to drive an impulse turbine. If the head loss through the nozzle is expressible as 0.04 E 2g (a) Determine the jet diameter that will give a jet of maximum power. (b) Evaluate this maximum Jet power. Dropared by: ENGR REVNA LDO R MAGAY
In the diesel oil transfer facility (ρ rel = 0.85), from the storage tank to the consumption tank, we want to install a pump to circulate a flow of 45 lt / s. The 400m long pipe is cast 150mm in diameter and consists of a check valve, a gate valve and 2 commercial medium radius elbows. The consumption tank is pressurized to 3.8 bar of manometric pressure. Determine the drive power of the pump in kW if its performance is 68%. Additional data, load loss factors: 1. Check valve Kr = 1.5 2. Gate valve open Kv = 0.21 3. Commercial elbow of mean radius Kc = 0.75, for each elbow 4. Storage tank outlet sharp angles Ks = 0.5 5. Entrance to consumption tank Ke = 1 6. Pipe friction factor f = 0.025
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.