Can you solve this question? Example 1:In the power system shown, bus 1 is a slack bus with V, = 120° per unit andbus 2 is a load bus with S, = 280 MW + j 60 MVAr. The line impedance on abase of 100 MVA is Z = 0.02 + j 0.04 per unit. Using Gauss-Seidel method,determine V,. Use an initial estimate of V,0) = 1 + j 0 and perform fouriterations.Z12 0.02 + j0.04Sa = 280 MW +j60 MvarFig 4.2 Onc linc Diagram for thc givcn problem

Example 1: n the power system shown, bus 1 is a slack bus with V, = 1Z0° per unit and %3D us 2 is a load bus with S, = 280 MW + j 60 MVAR. The line impedance on a ase of 100 MVA is Z = 0.02 + j 0.04 per unit. Using Gauss-Seidel method, etermine V,. Use an initial estimate of V,0) = 1 + j 0 and perform four erations. Z12 0.02 + j0.04

Example 1: n the power system shown, bus 1 is a slack bus with V, = 1Z0° per unit and %3D us 2 is a load bus with S, = 280 MW + j 60 MVAR. The line impedance on a ase of 100 MVA is Z = 0.02 + j 0.04 per unit. Using Gauss-Seidel method, etermine V,. Use an initial estimate of V,0) = 1 + j 0 and perform four erations. Z12 0.02 + j0.04

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.72P

See similar textbooks

Similar questions

In the power system network shown in Figurebelowbus 1 is a slack bus with V = 1.020° per unit and bus 2 is a load bus with S2 300 MW + 80 Mvar. The line impedance on a base of 100 MVA is Z = 0.01 + j0.02 per %3D unit. (a) Using Gauss-Seidel method, determine V. Use an initial estimate of = 1.0 + j0.0 and perform two iterations. i.e.Deternine(a)V2 and (b)V½? Z12 = 0.01+ j0.0 2 2 S2 300 MW+80 Mvar (a) 0.954 - j0.052 (b) 0.949 - j0.0517 (a) 0.914 - j0.0152 (b) 0.949 - j0.0517 (a) 0.945 - j0.025 (b) 0.994- j0.0571 (a) 0.965 - j0.0255 (b) 0.914 - j0.0529
following figure shows the one-line diagram of a power system. Bus 1 is selected as a reference bus (slack bus), and bus 2 is load bus. Using the Gauss-Seidel method, determine the value of the voltage at the load bus 2 and perform two iteration. Moreover determine the complex power flow at bus 1 and also active and reactive power in transmission line. The line impedance on a base of 100 MVA. Use an initial estimate of V,º = 1+ j(0) . S1 Z12 = 0.02 + j0.04 2 S2 = 280 MW +j60 Mvar
In the power system network shown in Figurebelowbus 1 is a slack bus with V = 1.020° per unit and bus 2 is a load bus with S2 = 300 MW + j80 Mvar. The line impedance on a base of 100 MVA is Z = 0.01 + j0.02 per unit. (a) Using Gauss-Seidel method, determine V2 . Use an initial estimate of V0) = 1.0 + j0.0 and perform twoiterations. i.e.Deternine(a)V2' and (b)Vz? Z12 = 0.01+ j0.0 2 2- S2 =300 MW +j80 Mvar (a) 0.914 - j0.0152 (b) 0.949 - j0.0517 (a) 0.945 - j0.025 (b) 0.994- j0.0571 (a) 0.954 - j 0.052 (b) 0.949 - jo.0517 (a) 0.965 - j0.0255 (b) 0.914 - j0.0529
Q2. Figure Q2 shows the single-line diagram. The scheduled loads at buses 2 and 3 are as marked on the diagram. Line impedances are marked in per unit on 100 MVA base and the line charging susceptances are neglected. a) Using Gauss-Seidel Method, determine the phasor values of the voltage at load bus 2 and 3 according to second iteration results. b) Find slack bus real and reactive power according to second iteration results. c) Determine line flows and line losses according to second iteration results. d) Construct a power flow according to second iteration results. Slack Bus = 1.04.20° 0.025+j0.045 0.015+j0.035 0.012+j0,03 3 |2 134.8 MW 251.9 MW 42.5 MVAR 108.6 MVAR
The Gauss-Seidel is an iterative method used to solve a set of nonlinear equations in the power flow. For the power network shown in Figure below, bus 1 is a slack/swing bus with V1 =1.0 L per unit and bus 2 is a load bus with P2 = 280 MW and Q2 = 60 MVar. The line impedance on a base of 100 MVA is Z = 0.02 +j0.04 per unit. Using Gauss-Seidel method, show how you determine V2 (first iteration only), and the power loss in line 1-2. Use an initial estimate of per unit but do not need to solve them numerically. After four iterations the voltage at bus 2 converges to per unit. Z12=0.02+j0.04 PL
By using Gauss-Siedal method, the voltage of the bus 2 after two iteration is Your answer By using Gauss-Siedal method the voltage of the bus 3 after two iteration is Your answer For a system consist from 3 buses and bus 1 is the slack bus. The data of the system are:- 0.25 -0.2 -0.05 Ybus j -0.2 0.225 -0.025 p.u. -0.05 -0.025 0.075 V₁=1+j0 p.u., P₂+jQ2-0.6+j0.25 p.u., P3+jQ=0.8+j0.5 p.u.
Q4// for the power system as shown in the figure below, using Gauss-Seidel, determine the voltages at bus-2 and bus-3 after first iteration. V₁ = 120° P.U Slack bus 0.4+ j0.3 P.U (3) (1). jo.025 P.U jo.05 P.U j0.2 P.U -(2) 0.8+ j0.6 P.U
A network consisting of a set of generator and load buses is to be modeled with a DC power flow, for the sake of conducting a contingency analysis. The initial flows calculated with the DC power flow give the following information: f°2-4 = - 65.3 MW and fº4-5 = 13.6 MW. The following values of LODF and PTDF factors are given: PTDF54,2-4 = -0.2609, LODF2-4,4-5 = -0.6087. Calculate the contingency flow on line 2-4 due to outage of line 4-5. Select one: O a. -75.5MW O b. None of these O c. -68.85MW O d. -73.58MW O e. 75.5MW O f. -61.75MW
How do we handle a PV bus in the Gauss Seidel Method? What will happen to the bus voltage if the reactive power at a PV bus exceeds the upper bound? And why?
3. Which one of the following method uses weak coupling between reactive power and voltage angle?. A. Newton - Raphson Method B. Decoupled Method C. Gauss-Seidal Method
A loss less TiL with characteristic impedance of to is terminated in Zr=3Z0. use crank diagram to sketch the voltage versus distance from the load, (Assume vst = 1 volt). @ Repeat the above How for Zv=Zo/3-
Consider a 3-bus system of the reactive network in Figure below where bus-bar 1 is slack. Use Gauss-Seidel method to determine the voltage at bus 2 and bus 3. Compute the power at bus 1, the line flow and line loss. V₁ = 2.520° $₁ Z12 = j0.2 Z13 = j0.5 V₂ V3 S₂ = j5 S3 = j2