f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Thank you Y=15 kN/m4'=28°c'-04mG.W.T.Yu 20 kN/m4'-33°4mThe above figure shows a concrete gravity retainingwall supporting two layers of soil.Answer the following questions (a, b, c, d, e, f, g &h).Note:1. Use Rankine's theory of active pressure.2. Complete solution with diagrams is required forPS2.3. In all the steps in your solution, round the answersto three decimal places. This is important so youranswer will match the answer key.

Introduction- A wall is a framework and a surface that distinguishes an area, supports a load,…

f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Thank you

f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Thank you

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3m W.S 3 10 6m 6m 10 W.S Sm 6m 6m draln 1. A section of a gravity masonry dam is shown in the figure water is flush at the top of the dam upstream and 5m from the ground downstream. Assume hydrostatic uplift to vary uniformly from full hydrostatic pressure from the heel to zero at the drain density of water is 1000kg/m^3. The specific gravity of concrete is 2.4. Determine: a. The location of the resultant force b. Factor of safety against sliding if coefficient of friction is 0.75 c. Factor of safety against overturning d. Stress at the heel and the toe e. Unit horizontal shearing stress at the base f. Factor of safety against overturning neglecting uplift
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.74 ksi. Determine the hoop stress in the wall of the tank. O 55.7 ksi O 40.8 ksi O 77.8 ksi O 59.6 ksi O 66.1 ksi
The gate shown is hinged through a point A and is restrained from opening by a fixed ridge at point B. For a gate width of 7 feet. Determine: a. the magnitude and direction of the hydrostatic force acting on the gate using the PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/ prism as part of your solution. express your answer in klps. b. magnitude and direction of the force exerted on the plate by the ridge. Illustrate abd label the FBD of the force system. Express your answer in klps.
An open top standpipe as shown has d = 2.5 m and 30 mm wall thickness. Determine the height ? (?? ??????) of the water that will result to a circumferential stress of 10 MPa in the wall of the standpipe. NOTE: The specific weight of water ?? is 9.81 3. Remember, pressure is equals to the product of m specific weight and height. Use 2 decimal places
The gate AB shown in figure is hinged at A and kept closed by a force P at B. Compute for the Hydrostatic Force acting on the side of the gate AB. (Given: p = -18.46 kPa, OIL SG = 0.8)
An open top standpipe as shown has a radius r= 2.2m and 20 mm wall thickness. Determine the height ? (?? ??????)of the water that will result to a circumferential stress of 24MPa in the wall of the standpipe. NOTE: The specific weightof water is 9.81???3. Remember, pressure is equals to the product of specific weight and height. Use 2 decimal places.
Q-1: Water is flowing through a soil as shown in the figure. Determine the elevation, pressure, and total heads at points A through D. Also, find hydraulic gradient. F E 5 m 3 ml 4 m 2 m 7 m Datum A B C Ꭰ DI Soil
Given is a thin-walled tube with the following data: Determine the following: a. Enclosed Area Wall thickness- 2mm b. Perimeter of the thin walled tube ABC is a sector with a radius of 50 mm c. Shear flow AOD & COD is a triangle Torque is 1000 N.m Length of the thin walled tube is 0.5 m Use G=24 GPa for aluminium d. Shear stress e. Angle of twist A R, 90° В 3R
View Policies Current Attempt in Progress A 40-mm-diameter solid shaft is subjected to an axial force of P = 2410 N, a vertical force of V = 1560 N, and a concentrated torque of T= 65 N-m, acting in the directions shown. Assume L = 130 mm. Determine the normal stress a, at point H. О 34.2 МPа O 31.2 MPar O 40.4 MPa O 42.8 MPa O 46.5 MPa 144 acer
An embankment load on a silty clay soil layer as shown below. Determine the stress increase under the embankment at points A and B that are loaded at a depth of 6 m below the ground surface. 5 m 1H:2V, 1H:2V 1H:1V 8 m Y=18 kN/m Y=18 kN/m3 6 m A Cs Scanned with CamScanner B. -..
CORRECT LETTER PLS 1. Which of the following least affects hydraulic gradient or slope of HGL? A. PIPE LENGTHB. PIPE DIAMETERC. TYPE OF PIPED. FLOE RATE 2. In laminar flow, which is correct?BJ: higher Re value has higher friction factorJB: lower Re value has lower friction factorGroup of answer choices A. BJ is false and JB is true B. BJ is false and JB is false C. BJ is true and JB is false D. BJ is true and JB is true 3. In a system with 4 reservoirs and 2 pipe junctions, how many continuity equations are formulate? A. 3B. 2C. 1D. 4E. 5
Problem Refer to the figure shown. Determine the following considering the effect of the Prestressing force and Working loads simultaneously. 12 kN/m Section: 10 kN/m С.G. 750 mm 200 mm A 8 m 7 m 350 mm a. Determine the ftop at x=8 m from left end. (MPа). b. Determine the fbot at x=8 m from left end (MPа).