yFlood waterGround LevelFigure Q1b 8wa (w* -y)(b) An engineering intem has designed a flood defence barrier. The barrier hasa rectangular cross section of width 2w and height h above ground level asshown in Figure Q1b. The intern has provided the following solution for thein-plane stresses (N/m?) in the barrier:pgx'y pg3xyw22w3xy34w3Pg (xydypgx23pg(w²-y2)-3xy%3D4w w?3pgTry(x*w²- x²y?) +pg%3D8w320w8wa (w*-y)where p is the density of the flood water, g 9.81 m/s? is the gravitationalacceleration, and (x, y) are rectangular Cartesian coordinates centred asshown in Figure Q1b.Determine the magnitude of the principal stresses at the material pointidentified as A in Figure Q1b, ifp= 1000 kg/m³, w = 0.5 m, and h = 4 m.

According to given data g=9.81 m/s2ρ= 1000 kg/m3w= 0.5m (Cross section width = 2w )h= 4 mNeed to…

Answered: Flood water A Ground Level

Engineering

Civil Engineering

Flood water A Ground Level

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter15: Site Plan Layout

Section: Chapter Questions

Problem 15.12Q

See similar textbooks

Related questions

Q: 10 ft

Q: For the shaded area: a) Determine x-coordinate of the centroid (in mm) b) Determine the…

Q: 3 - 6" wide d= 18" - 0" Figure 2.5.4 - Question 4 Inside perimeter Outside perimeter Centreline

A: A circular ring of plan is given. Inside diameter, D1 = 18 feet Width of ring , t = 3 feet 6…

Q: Compute the DMD of Line 1-2 of the traverse data shown. LINES LATITUDE DEPARTURE DMD DOUBLE AREA 1-2…

Q: How circular level bubbles adjusted?

A: Bubble level is an instrument designed to indicate whether a surface is horizontal level It is…

Q: Determine specific energy and critical depth

A: Given data : Width (B)=5.5 mDischarge (Q)=16.5 m3/sDepth (Y)=1.5 m

Q: Water surface 1.5 m 60 Gate Side view Gate Top view 1 m

A: Force on gate is passing through centre of pressure of plate.

Q: NWC M= 50 ft.

Q: What is Energy Gradient Line (EGL)?

A: Hydraulic engineering commonly use the terminology Energy Gradient Line and Hydraulic Gradient Line.…

Q: Find the volume to be excavated if the ground surface is to be leveled to elevation 5m.

A: Givendata: The elevations of the ground surface at each corner of the square section are given as:…

Q: the required super elevation is

Q: Draw the plan and elevation of the given line diagram. W W.C V KITCHEN D, 2100×1200 3600x2800 BATH V…

Q: The surfaces r = 3 and 6, θ = 20◦ and 150◦, and φ = 10◦ and 120◦ identify a closed surface. Find (a)…

Q: Wembley Stadium

A: Wembley Stadium is located in London and know for holding important football matches. The design of…

Q: 2. £{est}

A: Given L{e5t}

Q: Complete an interpretation drawing that show permissible surface condition that lies partiall part…

A: The permissible surface condition is as follows. When a tangent modifier is added it only controls…

Q: Find the maximum permissible height of water in the

Q: L- w 22 N/m L= 15 m

Q: shaded area. Ans. X 244 mm, Y = 117.7 mm 200 mm - 200 mm 150 mm 125 mm 60 mm 125 mm

A: As per Bartleby guidelines we are supposed to solve only very 1st problem . So send your other…

Q: 13. Free board is provided in channel design only for: a) Loose boundary channel b) Rigid boundary…

A: Given data Free board Channel design To be discussed Related open channel flow

Q: Determine change in volume of the block.

A: Given data, Steel block is subjected to a, hydrostatic pressure is=10 MPaYoung's modulus=150…

Q: 2 and 3, please.

A: 2. 1. Insufficient Joint Clamp Force The majority of bolted joints depend on the clamping force,…

Q: 40 kN

Q: Sign Convention 250KN 300KN CW CCW 15 2m 2.5m

Q: Define Passive Condition

A: Passive Condition: It is the condition when soil moves away from the soil, due to the seismic load…

Q: stream, the water flows 0.71m dee ace in the apron.

A: We know equation :2q2g=y1y2(y1+y2)q=Qw=18023.5=7.659m3s·mso,2(7.659)29.81=0.71y2(.71+y2)y2=3.7647m

Q: Compute the flow rate at water depth "y" = your Roll No (FPS system) %3D 0.025

A: GIVEN DATA Let us assume the depth as y=10ft (y=YOUR ROLL NO) n=0.025, so=0.002, calculate the…

Q: S=25

A: Given- Thickness (t)=10 mmInternal diameter(di)=25m Pressure (P)=25Mpa

Q: Define Blanket Drains.

A: A blanket drain is a drainage system that is used on the road cut to handle seepage areas.

Q: Drainaige system

A: ● Solution:- Flow of water through a well-defined channel is known as drainage we can say that a…

Q: A rectangular field is fenced off, an existing wall being used as one side. If the area of the…

Q: Explain water stage and its measurement. Also describe selection of site for stage

A: 1. Stage measurement are most commonly required in surface water hydrometry to determine the flow…

Q: a. A 40-ft long (into the page) Tainter gate is shown below. It is being used by the U.S. Army Corps…

Q: Given a three-pipe system, the total 150,000 Pa, and the elevation drop data are:

Q: LOT TECHNICAL DESCRIPTION LINE BEARING LENGTH N 35 E S 78 E S 23° E S 35°W N 71 W 1-2 14.00M 2-3…

A: To Determine Correction of the Traverse. Draw plan of the Traverse in 1:100m scale.

Q: What is the DMD of Line 3 - 4? LINES LATITUDE DEPARTURE DMD DOUBLE AREA 1-2 + 60 -30 2-3 - 20 + 20…

A: Answer : Option (a) is correct.

Q: Freeboard is the vertical distance from the water surface to the bottom of the channel

A: Freeboard is the extra vertical distance provided from free water surface level to the top level of…

Q: calculate the water surface elevation

Q: 9- Crest stages gages used to readings A- Average depth of stream flow. B- Depth of stream flow. C-…

A: Explanation : Crest stage gages are made of 14 inch dia pipe which are installed vertically in the…

Q: Define artificial rain

A: Arificial Rain

Q: Define oriented water.

A: Oriented water or water oriented:

Q: Q18. Draw the plan and elevation of the residential building with the following dimensions. Assume…

Q: Find the total area

A: Consider the figure,

Q: the nominal cover

A: Given, Figure shown the reinforced beam section. The nominal cover provided at the bottom of the…

Q: ! (asap)

A: Profile of line control establishes two dimensional control tolerance zones around the surface.

Q: Surveillance at point A of the report and the altitude of 250.00 m according to the heritage…

A: Elevation of all points given below

Q: 8. Free board is provided in channel design only for: a) Loose boundary channel b) Rigid boundary…

A: (Note: Since you have asked multiple questions, we will solve the first question for you. If you…

Q: Define sound quality

A: Sound quality:

Concept explainers

Principles of Seepage

In hydrology, when water flows down in a pore or crack of unsaturated soil due to gravity, the deep layer of soil is called seepage. It is the slow movement of water in the soil layer. Seepage is mainly found near hydraulic structures and is responsible for the stability of earthen-type hydraulic structures.

Question

100%

8wa (w* -y)
(b) An engineering intem has designed a flood defence barrier. The barrier has
a rectangular cross section of width 2w and height h above ground level as
shown in Figure Q1b. The intern has provided the following solution for the
in-plane stresses (N/m?) in the barrier:
pgx'y pg
3xyw2
2w3
xy3
4w3
Pg (xy
dy
pgx
2
3pg
(w²-y2)-
3xy
%3D
4w w?
3pg
Try
(x*w²- x²y?) +
pg
%3D
8w3
20w
8wa (w*-y)
where p is the density of the flood water, g 9.81 m/s? is the gravitational
acceleration, and (x, y) are rectangular Cartesian coordinates centred as
shown in Figure Q1b.
Determine the magnitude of the principal stresses at the material point
identified as A in Figure Q1b, ifp= 1000 kg/m³, w = 0.5 m, and h = 4 m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

net area along 4,5,2,6,7
BEAUTIFUL 01/ Construct Polynomial Forth function gases in cas, within [0, 1]ns4
x+sinx 2. limg»00 x+cosx
Draw profile ? note//Lengthe of each station is 10m .
Please check Elevation for Last point B.
Please show all steps Given the following Information, what is the Elevation of Point B? STA A HI 1.572 STA HCR VCR SD HR DESC B 0:00:00 87:06:55 87.006 0.700 NAIL Point Elevation A 1180.525
Compute L, T, E, M, LC, R, and stations of the PC and PT for the highway curve with D,-4'00, I-13 30', and Pl station 19+22.00 ft. Use the arc definition for the highway curve. Part A What are radius R and length L7 Express your answers in feet to two decimal places separated by a comma. 19Η ΑΣΦ. 11 Ivoc R.L- Submit Part B Request Answer What are distances T, E, M, and long chord LC? Express your answers in feet to two decimal places separated by commas. VAX T. E. M, LC= Submit Part C Request Answer ft Ivec ? ft
Please help me. Thank you! <3
3.2 Using the average-end-area method, calculate the cut-and-fill volumes for stations 19 + 00 through 24 + 00. End-area End-area Volume of Volume of fill (sf) cut (bcy) fill (ccy) Station cut (sf) 19 +00 326 0 20+00 157 21 + 00 44 21 50 0 22 + 00 147 23+00 ㅇ 165 24+00 0 133 SHOT ON HOT 7 PRO O Al QUAD LENS
Q1:- A lot (ABCDF) with a curved boundary (FA) (whose radius DF-DA-40 m) is cut off by a fence (JK), Compute: - 1- Length and Azimuth of line JK. 2- Coordinate of point K. 3- Cut off area (ABJK). (400, 700) с J Dom B 286 21 go tom 30m (due w) A(500, 500)
Plz 1 , 2 and 3
Line to be established B. Figure 1