Flowchart of how to estimate EARTHQUAKE LOADS. Please write it down, don't use the book nscp. Thanks.

Q: Determine the force in members bd, be,de & gh of truss shown in figure 3m 4m f 4m 400 KN #1 d + 4m b…

A:

Q: d one bending momen ure) are applied to a 50 id shaft. Two shear for

A: Given:-d=50mmTo find:-principal stresses

Q: The lowest temperature expressed in * multiple of 2 C at which the oil is observed to flow after…

A: The Oil hazes into crystal at the cloud point yet flows at the pour point.

Q: 5m C KN m 2 KN lm 2m 2m JKN 3. B

A:

Q: Problem 4 Two tanks are connected using a manometer. Air is trapped in the right tank above the…

A: To find out the difference in Piezometric head of water between left and right tank.  Where,  H =…

Q: 3. The bars AB and BC of the structure are 4m in length. A load of 10kN is placed at D and another…

A:

Q: Compute the future value of a $1500 deposit, after eight years, in an account that pays a simple…

A: Given:- The present value of the deposit = $1500  The time period of the deposit is 8 years The…

Q: The frame carries a cylinder that weighs 80lb. Calculate the support reactions at C and D. Assume…

A: To Determine :- The support reactions at C and D.

Q: Column AB is made from high strength pre-cast concrete and reinforced with four in diameter A-36…

A: Given : To Find : Pmax = ?

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A slurry has a percent solids of 30%, and the volume of the solids is 2,100 mL. If the weight of the…

A: Given data:- The given Percent of Slurry,  30% The given volume of solids is 2100 ml The weight of…

Q: Determine the Support reaction at A And B? 4 m w=15 kN/m 3m 3m

A:

Q: IN THE FIGURE SHOW, IT IS DESIRED TO DETERMINE THE LENGTH OF AB ACROSS A WIDE AND DEEP RIVER. LINE…

A:

Q: ention in details the classes of soil water.

A: The soil water is classified in following three types. Gravitational water Cappilary water…

Q: what's the reason behind (14/2 + 2)

A:

Q: Define percussion bits

A:

Q: What is the importance minimum requirements system? of application of in building design

A: One of the cornerstones of developing a successful project is understanding the technical…

Q: The Bulk Modulus of Elasticity of water us approximately 300 000 psi. If the temperature is 60°F,…

A: Given data:- The given value of Bulk modulus, EB=300000 psi The given temperature is, T=60°F The…

Q: Question 1 Table 1 shows the summary of a closed loop traverse carried out in campus by a group of…

A:

Q: 2. Obtain the general solution. (Let 2C=C) (4x + xy²)dx + (y + x²y)dy = 0

A: From the given question it is required to determine the solution of differential Equation…

Q: A column of size 200 x 300 mm has an effective length of 3 m and is reinfor pomors with 6 nos. 20 mm…

A: Given data- column size 200×300 mm,effective length leff=3 m=3000 mm6 bars of 20 mm dia,M20 concrete…

Q: FRESHMEN What is the value of F required to balance the weight of the cylinder if the weight of the…

A:

Q: Q16 for the frame shown Figare determin the horizontaand vertical componets of the linB on meber A B…

A:

Q: QFor the rectangular footing with dimensions (3*6) -how in figure (4). Calculate the immediate…

A:

Q: 5Q. The plate is moving at 0.6 mm/s when the force applied to the plate is 4 mN. If the surface area…

A:

Q: 5.3 Magnitude of effective length of compression member depends upon A) ocation where member is used…

A:

Q: What are the reasons for canal linings?

A: Canal lining is basically providing an impermeable layer over the canal bed and sides to protect the…

Q: Name 3 project delivery methods and elaborate on their advantages and disadvantages (in your own…

A: Project delivery methods in Construction engineering.

Q: ACTIVITY 2: Determine the (internal Di, external De and total D) static indeterminacy of the…

A: Given, Different type of 2D Beam structures

Q: Q/ For the rectangular footing with dimensions (3*6)► Show in figure (4). Calculate the immediate…

A:

Q: 4. The beam AB supports a 2.5kips per feet uniform load and a 15kips concentrated load as shown.…

A:

Q: 2. A Vertical sag curve has a descending grade of - 4.20⁰ and an ascending grade of +3,0 %…

A: g1 = 4.2%g2 = 3%L = 260mElev. PI = 96mdia = 1mCulvert is burried by .70m   Find - Location of the…

Q: Consider a linear elastic rectangular thin sheet of metal, subjected to uniform uniaxial tensile…

A: Given data- A linear elastic rectangular thin sheet of metal- σx=100 MPa,σy=0 MPa,σz=0 MPa,E=200…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A:

Q: Q4-For the shaded area shown in Figure (4), determine: a. The x coordinate of the centroid (x'). b.…

A: Given A shaded cross section  Required : X coordinate of cenyroid Moment of inertia about x axis

Q: Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties…

A: Given: b=500, 200 mm d=650-50=600 mm n=7 As=3×π×2824=1847.25648 mm2 Beam condition=Cracked

Q: What is the maximum shear and maximum moment. Beam 3.

A:

Q: RIIf the width of the regulator 3 is 5m and Zbeam = 4.55*10² m². find the maximum water depth when…

A: Given- A rectangular beam Width=3m section modulus=4.55×10-4m3 Required- to calculate maximum depth…

Q: Explain Multiroller

A: It is term related to geotechnical engineering.

Q: Material Strengths: Fy = 248 MPa, Fu = 400 M Pa The diameter of the holes in the 12 mm - thick plate…

A:

Q: Determine the design snow loads for the roof of the gabled frame of an apartment building shown in…

A: Given: Pg = 25 psf Ce = 1 Ct = 1 Is = 1

Q: Calculate the Angles. Plot the bearings and azimuth.

A: Given data- Azimuth, OX=190°25'Azimuth, OY=270°OZ=N75°10'E Required- to calculate angles XOY and…

Q: The five-bolt connection must support an applied load of P = 1600 lb. If the average shear stress in…

A:

Q: Determine the allowable (ASD) tensile strength (kN) of the angle shown. The plane of connection lies…

A:

Q: Two individuals are attempting to relocate a sofa by applying forces in the indicated directions. If…

A: The magnitude of force, F1 =540 NThe magnitude of force, F2 =300NThe angle between the two forces, θ…

Q: Determine the vertical reaction at support D in KN. Determine the maximum shear force in KN.…

A: Given data  Find support reaction, maximum shear force and maximum positive and negative moment.…

Q: A 30 m steel tape weighing 1.2 kg is of standard length under a pull of 5 kg supported for full…

A:

Q: 1. Simply supported beam, 6 in by 12 in, fb = 600 psi, find center load P =? (Include self-weight,…

A: Given  Unit weight of concrete= 150 pcf

Q: 6. A 12 - m simply supported beam is carried by two concentrated loads. The loads present are 35 kN…

A:

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A:

Pricing Construction Equipment

Pricing construction equipment means estimating the cost of operation of all the construction equipment used in a construction project. The pricing is done based on two factors – ownership cost and operating cost of the equipment. Thorough knowledge of the ownership and operating costs is necessary for proper project management and executing profitable construction.