FLUID MECHANICS/CHAPTER 4 Exercise 4.11 Two tanks filled with water connected by a serial pipe 25 m. AB pipe has a diameter 10 cm for the first 15 m and BC pipe diameter is 16 cm for the remaining of its length. The flow rate of water entering the pipe is 0.007 m³/s. If energy losses because of the shock loss at sudden enlargement and friction only, calculate level difference of two tanks if f = 0.01 for both pipes. Solution for Exercise 4.11 (Answer: 0.273 m)

FLUID MECHANICS/CHAPTER 4 Exercise 4.11 Two tanks filled with water connected by a serial pipe 25 m. AB pipe has a diameter 10 cm for the first 15 m and BC pipe diameter is 16 cm for the remaining of its length. The flow rate of water entering the pipe is 0.007 m³/s. If energy losses because of the shock loss at sudden enlargement and friction only, calculate level difference of two tanks if f = 0.01 for both pipes. Solution for Exercise 4.11 (Answer: 0.273 m)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An industrial oil (s.g. = =0.85) is flowing at 160 gallons per minute (gpm) in a system with the following details: SUCTION: Standard elbow and the pipe is 7 foot-long. DISCHARGE: Street type elbow and the pipe length is 42 feet. Neglecting losses due to the filter and the hydraulic press, compute: (a) The total energy loss due to friction (suction and discharge pipes) (b) The total energy loss due to minor losses (suction and discharge) 3" Schedule 40 Pump 4" Schedule steel pipe 40 steel pipe Hydraulic Filter press Flow 4.0 ft 早 L0 ft 2.0 ft Reservoir
Oil flows through a 16 tube single cooler with a velocity of 2 m/s. The internal diameter of the tube is 30 mm and oil density is 0.85 gm/ml. Find the volume flow in liters per sec. Answer asap plss. Thanks. I will rate helpful
1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
Centrifugal pump has differential pressure 15 bar and use to transport oil between two separators. If the pressure at first separator is 4 bar calculate the pressure at second separator and NPSH. Where: Suction and discharge pipe diameters = 10 inch, Suction pipe length = 16 m, ld Oil level at first separator 3 m2d Oil density=880 kg/m³ P Oil flow rate=0.092 m³/sec e Pipe roughness= 0.045 mm Discharge pipe length = 25 m O Oil level at second separator = 5.5 m2d Oil viscosity = 9.5 x 10³ Pa.s Oil vapor pressure 22.5 kPa d кра 4.5x10²
A Crude oil of specific gravity 0.81 and kinematic viscosity of 4.28 stoke is flowing through a pipe of diameter 460 mm at the rate of 4900 liters/sec. find the velocity, Reynolds Number & head lost due to friction for a length of 45 m of the pipe. Take the co-efficient of friction as 0.0058. Also find the Power required (in kW) to maintain the flow.
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
The losses per unit length pipe^h/l in turbulent flow through small pipe depend upon Velocity, Diameter, Gravity, Dynamic viscosity and Density. Determine the general from of equation.
Example: In a 45° bend a rectangular air duct of 1 m? cross-sectional area is gradually reduced to 0.5 m² area. Find the magnitude and direction of force required to hold the duct in position if the velocity of flow at 1 m? section is 10 m/s, and pressure is 30 kN/m². Take the specific weight of air as 0.0116 kN/m³. Solution: Fay 45° Fzx PA, cos 45° 45° Vzcos 45° 2. 45°
Q5/ Oil flows in a 0.3 (m) diameter pipe with a flow velocity of 2.7 (m/s). The physical properties of Oil are: 1- Dynamic viscosity is 0.39 (N.s/m²). 2- Density, p = 950 (kg/m³). Find: 1- The value of Reynold's Number Re and Mention the Type of flow. 2- The value of coefficient of friction f of the pipe. ---- ----- --
The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and smaller ends are located 8 meters and 4 meters, respectively, from a datum line. If at the larger end the velocity is 1.2 meters pee second and the pressure is 5300 kN/m^2, compute the pressure at the smaller end
Problem-4: The characteristics for a pump are given in the table below. The pump is required to left water against static head Az = EN" m. The pipe arrangement has a total length L the pump discharge, head, efficiency and power for the given pipe system. 200, d = 0.1 m and f= 0.016. Find %3D Q (L/s) 10 20 30 35 42 50 Hp (m) efficiency % 210 201 180 150 129 93 48 30 58 80 85 86 74 EN=62 Hp = Az + h, = Az + 12.1 d P = 757
Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water. Ignore any changes in Kinetic or potential energy and assume isothermal flow (ie. Internal energy is constant, this is normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump starting with full energy balance and simplifying to solve for the pump head symbolically. Then begin careful of unit, solve for pump head in feet. Given erosion 500 gpm P=62 lbs/ft^3 A- 10.5 ft B- 100.8 ft C- 50.1 ft D-80.7 ft