For the bent pipe shown in the figure, it is sought to replace the system of three forces with a single force couple system located at point O. Enter the value of the resultant couple M in Nm (take the counter-clockwise direction to be positive). a 362 N, b-131N 50 N 0.25 m 0.25 m a 0.25 m 0.2 m

For the bent pipe shown in the figure, it is sought to replace the system of three forces with a single force couple system located at point O. Enter the value of the resultant couple M in Nm (take the counter-clockwise direction to be positive). a 362 N, b-131N 50 N 0.25 m 0.25 m a 0.25 m 0.2 m

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.6P: Find the internal force systems acting on sections 1 and 2.

See similar textbooks

Related questions

Q: The weight of one dozen apples is 4.6 lb. Determine the average mass of one apple in both SI and US…

A: A rule of thumb is a practical and approximate way of doing or measuring something, based on…

Q: The working gas of a thermodynamic cycle is a diatomic gas (assume constant specific heats.) The gas…

A: The initial pressure is The initial volume is The initial temperature is Process A-B constant…

Q: An aluminum kettle weighing 2 kg holds 2 litres of water and its heater element consumes a power of…

A: Here we will apply the simple heat formula.

Q: Consider the cycle in the diagram (very similar to the Rankine Cycle) using water as the working…

A: The boiler pressure is The condenser pressure is The mass flow rate is

Q: 6. A tank in a shape of a cone having a diameter of 2 m and a height of 3 m is filled with water.…

Q: B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine-…

A: In four stroke engine, there are four strokes which competes the cycle.The four processes are:(i)…

Q: Write down the nodal equation for an inside corner node with inside surface exposed to convection as…

A: Given:To find:Write the nodal equation.

Q: The extension, y, of a material with an applied force, F, is given by y = eFx1x10-3. a) Calculate…

A: Find out:Calculate the work done if the force increases from 100 N to 500 N using:An analytical…

Q: B1 1.- You have the following manufacturing system: 10% I M1 10% 20% I 90% B21 AS * the total…

A: "Since this is a question with multiple sub parts therefore solutions to only first three sub parts…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: a = Ö || i i ft/sec² rad/sec²

Q: The relation between the heat flux q", heat flow rate q, and area A normal to the direction of heat…

Q: 10 10¹ D C 8 Fig.4 40° 8' B 5000 lb

A: Given : The free body diagram is,

Q: Draw the Front View and the two Auxiliary Views

A: FindWe need to draw the front view and the Auxiliary view of the object.

Q: The working fluid of a liquid-vapor cycle is 1kg of R-134a. The cycle operates between two pressures…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Helium flows through a 0.30-m-diameter horizontal pipe with a temperature of 20 °C and a pressure of…

A: Given : The diameter of pipe is The final diameterof pipe is is The flow rate is

Q: Industrial pipes Are stainless steel pipes more demanding about the flexibility design…

A: The objective of the question is to understand if the design flexibility of stainless steel pipes is…

Q: MILK 40° B C h Milk is poured into a glass of height 140 mm and inside diameter 66 mm. If the…

A: V = 1.2 m/sInside diameter = 66 mm

Q: Mike and Kelly Kyson were two small city teachers who happen to fall in love and get married. Soon…

A: Given:

Q: Q6- A 1.0-kW heater is constructed of a glass plate with an electrically conducting film that…

Q: the full combustion is at constant pressure and the temperature of the products is (3250°C).…

A: The inlet temperature of EthaneThe inlet temperature of Air=300oCThe outlet temperature of products…

Q: The total force of 125 KN is required of flange coupling that has 5 bolts also has a shearing stress…

A: Given Data

Q: The pressur of the air in the figure is 10.7 kPa, and the manometer fluid is of unknown specific…

Q: The diameters D & d piped, Venturi- meter like horizontal water flow sistem seen in the drawing is…

Q: A 10 kg weight is suported by a 3 m long, 3 kg components at A given a = 1 m, b=1m, 0-4 = C B D

Q: A vertical hydraulic cylinder has a 125-mm diameter piston with hydraulic fluid inside the cylinder…

A: Diameter of piston d= 125mmAmbient pressure = 1 barPressure inside cylinder =1500KPa

Q: The figure shows the chain drive of a bicycle. How far will the bicycle move if the pedals are…

Q: A compression-ignition engine with compression ratio of 14 is being designed. Pressureand…

A: The objective of the question is to calculate the pressure and temperature at the top dead centre of…

Q: A turbine accepts steam at 5000kPa, 100 m/s, and 600 °C and leaves at 100 kPa, 25m/s, and a quality…

A: Given:The inlet pressure of steam to the turbine The inlet velocity of steam to the turbine The…

Q: Given the cantilever beam with point loads, find the magnitude of the vertical reaction at A.…

A: The vertical reaction at point A,

Q: magnitude T 1000 N.m is applied ess is 60 MPa in each shaft, deter

Q: - For the one-dimensional steel bar fixed at each end and subjected to a uniform temperature drop of…

Q: H.W.3.5 Propylene (C3H6) is burned with 50 percent excess air during a combustion process. Assuming…

A: Find outthe air-fuel ratiothe temperature at which the water vapor in the products will start…

Q: Q: Pressure drop in slug flow-M. A light oil and a gas are flowing upward in a vertical tube of…

A: Given:The inner diameter of the vertical tube The superficial velocity of light oil The superficial…

Q: 4) A spherical container is filled with iced water at 0°C. The tank is made of iron (k=15 W/m.°C)…

A: Here we will calculate equivalent resistance and use it to get heat transfer

Q: To speed up the unrolling of a telephone cable the trailer with the reel of cable starts from t and…

A: Given :The accleration of cable is The accleration of trailer is The free body diagram is,

Q: Q1: A liquid-level system has a cross-sectional area of 3.0 ft². The valve characteristics are q=8 h…

A: For the initial condition (Given) We know basic flow rate equation:…

Q: Calculate the hydrostatic force and components of the semicylindrical protuberance located at the…

A: to find:the hydrostatic forcegiven:height of the tank length of the tank inwards radius of the semi…

Q: A 200 m long pipe slopes down at 1 in 100 and tapers from 0-25 m diameter to 0-15 m diameter the…

A: given:The length of the pipe is the slope is The diameter at 1 is The diameter at 2 is The volume of…

Q: An axial compressor with diameter of 0.8 m is being designed to run at 1500 rpm. The inlet guide…

A: Given:The diameter of a compressor is The revolution is The mass flow rate is The rotor blade angle…

Q: 12. A mixture of oil and gas flows through a horizontal pipe with an inside diameter of 150 mm. The…

A: We have mixture of oil and gas.Let assume that we have gas in x fraction of area.then (1-x) fraction…

Q: 1.4 The rotor of a millimeter-scale gas turbine engine has a radius of 1 mm. It has to reach a tip,…

A: Given:The radius of the rotor of a millimeter-scale gas turbine The tip or rim speed

Q: A combined gas turbine-vapor power plant has a net power output of 45 MW. Air enters the compressor…

A: “Since a question with multiple sub-parts, has been posted the solution only to the first three…

Q: 28 The velocity distribution in the boundary layer is given by: U y where u is the velocity at a…

Q: v = 4 m/s A P 30° 0.5 m the 5-kg collar A is sliding around a smooth vertical guide rod. At the…

Q: Water at 415°C has a pressure of 25MPa. Determine the specific volume of the water based on: ● a)…

A: (a) Ideal gas equationThe ideal gas equation only applies accurately to ideal gases at low pressure…

Q: . If the pipe carries 100 litres of oil of specific gravity 0.85 find the pressure at the lower end.…

A: The change in the elevation-

Q: 4.3 An incompressible fluid flows at a rate of 0.015 m³/s through a pipe AB with a diameter of 0.1…

A: Find out(a) The flow rate in the three branches(b) The velocity in AB, BC, and BE.Giventhe flow…

Q: At the instant shown, the arm OA of the conveyor belt is rotating about the z axis with a constant…

Q: 6-8 Consider a 3-link Cartesian manipulator, (a) Compute the inertia tensor J; for each link i = 1,…

A: (a) The inertia tensor for a uniform rectangular solid can be calculated using the following…

Question

Looking for a quick Handwritten, Don't delay.

For the bent pipe shown in the figure, it is sought to replace the system of three forces with a single force-couple system located at point O. Enter the value of the
resultant couple M in Nm (take the counter-clockwise direction to be positive).
a=362 N, b=131N
50 N
0.25 m 0.25 m
a
0.25 m
0.2 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculation of equivalent force couple system at point O

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q6: For the force-couple system shown in figure (6); determine an eguivalentcouple (M) and resultant force CR) at point (A). 1.5M 2KN 50ON.m osm 70° 015M 1-2 KN Fig (6)
For the bent pipe shown in the figure, it is sought to replace the system of three forces with a single equivalent resultant force R. Find the distance d (in metres) from point O to the point on the x-axis through which the line of action of R passes. a = 379 N, b= 146 N 0.25 m 50 N 0.25 m a b 0.25 m 0.2 m x
Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P 212 N and the couple M = 663 Nm. %3D M N m 150 N 300 mm 250 mm P N 400 mm 90 N Answer: Determine the angle (in degrees) that the resultant makes with the positive x-axis, which is in the same direction as the horizontal force P. Answer:
Q14: For the forces shown in figure (14),reduce this force system to an equivalent force-couple System a cting at point (0). Fg:(14) 2F
touch & OL166% 00:27 MENG250 - Practice Assi... Not saved yet •2-77. Determine the magnitude and coordinate direction angles of F, so that the resultant of the two forces is zero. Y2 B2 a2 y 60° 15°. F= 180 N O
The two forces, F1 = 20 kN and F2 = 4 %3D kN are acting on a system shown in the figure. If 01 = 45° and 02 = 45°, what will be the values of Rx, Ry, R %3D %3D and the angle (0) makes by R with .the positive x-axis Y+ 02 F2 Y- Ry (1) R,= F; (2) R,= Fy; (3)R = (R + R;); (4)0 = tan1 Rx اخترأحد الخيارات a. Rx = 20.13 kN, Ry = 4.99 kN, R = 20.74 kN and 0 = 13.92° %3D b. Rx = 17.72 kN, Ry = 9.31 kN, R = 20.02 kN and 0 = 27.72° c. Rx = 20.95 kN, Ry = 5.62 kN, R = 21.70 kN and 0 = 15.02° %3D d. Rx = 16.97 kN, Ry = 11.31 kN, R = 20.39 kN ande = 33.68°
Q 1: As seen in the figure, the pipe system is under the influence of force and force couples. Reduce the force system to a force and an equivalent force-couple system at point C. Find the angle O between these two vectors. 30 N A -0.3 m 30 N 0.3 m 0.5 m 0.8 m 80 N 0.7 m 0.25 m -0.6 m- 40 N 0.25 m 80 N
Replace the forces and couple moment system acting on the structure shown in the figure below by an equivalent resultant force, and find its perpendicular distance measured from point A. -3 m 5 kN.m 2.5 m 30 kN 10 kN/m 3m 6 m
F = 200 N F3=300N M = 100 Nm 0.4 m 300N 0.5 m 0.6 m The pipe system shown in the figure is supported by fixed joint at points O. Calculate the followings: (a) Replace the force-couple system acting on the pipe by a resultant moment and a single force acting on Point O. (b) Replace the force-couple system acting on the pipe by a wrench resultant and determine the coordinates of the point in the xz plane through which the line of action of the wrench passes.
Example (4): Calculate the magnitude of the moment about the base point O of the 600-N force-in twe different ways. 2 m Solution: A 40° 600 N 2 m F1 = 600 cos 40° 4 m 4 m F2 = 600 sin 40°
Difficult Problem: If magnitude of MA is 1200 kN – m and the distance between A and B is 3 m, what is the force FB and distance d so that the system shown at the right is equivalent to a force-couple system acting at point D, where the horizontal component of this force is R = 112 kN to the right and the corresponding couple is 635 counterclockwise. 60 kN 30 50 kN 2 m MA 60° 15° 200 kN m 100 kN 4 m Fs 2 m 200 kN 30 60 kN -3 m
H.W.: ComPute the magnitude and direction the vesultant of the two forces shown in figure. R=? 45 25 200N | 300M 11.5 360N