For the figure shown, have the following information: Bar (1) made of bronze E =100 GPa Bar (2) made of aluminum E =70 GPa A= 528 mm? The force in bar (2) is found to be 25 kN in tension, when the load P is applied. a. Compute the stresses in bars 1 & 2. A= 951 mm2 b. Found the deflection of point A. c. Determine the load P. Enter the stress of bar (2) in the box below in MPg upto 4 digits after the decimal point. Do not enter the units in the box. Upload the pdf file in the next question. Only PDF files will be accepted. Any other file will be rejected and will NOT be evaluated. (2) 0.8 m B 0.4 m 1.1 m 0.5 m 0.6 m (1)

For the figure shown, have the following information: Bar (1) made of bronze E =100 GPa Bar (2) made of aluminum E =70 GPa A= 528 mm? The force in bar (2) is found to be 25 kN in tension, when the load P is applied. a. Compute the stresses in bars 1 & 2. A= 951 mm2 b. Found the deflection of point A. c. Determine the load P. Enter the stress of bar (2) in the box below in MPg upto 4 digits after the decimal point. Do not enter the units in the box. Upload the pdf file in the next question. Only PDF files will be accepted. Any other file will be rejected and will NOT be evaluated. (2) 0.8 m B 0.4 m 1.1 m 0.5 m 0.6 m (1)

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter1: The Atom In Modern Chemistry

Section: Chapter Questions

Problem 16P: In the problem 15 above, what is vy , the y-component of the electron’s velocity, when it has...

See similar textbooks

Similar questions

Assume that a material has a FCC crystal structure, an atomic radius is 0.13x nm, and an atomic weightis 106.(x-5) g/mol.a) Calculate mass per unit cell for Palladium.b) Compute the unit cell volume.c) Find the mass density of Palladium in g/cm3 . (Avagadro number: 6.02x1023 atom/mol) (1nm = 10-9m).X: 8
For the alloy Mg-45 wt% Pb alloy at 500 C, what is the weight percentage of Pb in liquid?
1. What are the principal natural processes that affect the petrophysical properties of sedimentary rocks? 2. As shown in Table 1.1, the total bulk chemical analysis of rock samples is clearly different from the surface analysis. What effect does this have on the rock properties?
A polystyrene component must not fail when a tensile stress of 1.25 MPa (180 psi) is applied. Determine the maximum allowable surface crack length if the surface energy of polystyrene is 0.50 J/m^2 (2.86 10^-3 in.-lbf/in^2). Assume a modulus of elasticity of 3.0 GPa (0.435 10^6 psi).
A movie stunt performer is filming a scene where he swings across a river on a vine. The safety crew must use a vine with enough strength so that it doesn't break while swinging. The stunt performer's mass is 88.0 kg, the vine is 12.0 m long, and the speed of the stunt performer at the bottom of the swing has been determined to be 8.60 m/s. What is the minimum tension force (in N) the vine must be able to support without breaking? N Need Help? Submit Answer Read It
Determine the magnitudes of the forces C and T, which along with the other three forces shown, act on the bridge – truss joint. 3 kN 20 16 kN 40 8 kN
A) The contact angle for water on clean glass is close to zero. Calculate the surface tension of water at 20 C given that at that temperature water climbs to a height of 4.96 cm in a clean glass capillary tube of internal radius 0.300 mm. The density of water at 20 C is 0.9956 g cm-3. B) What change (if any) you will expect for surface tension in A if the contact angle will be between 10 º and 20 º?
- & Sketch New · C $ 7 ♡ www 1500 kg/m³ O 3000 kg/m³ 5000 kg/m³ 7000 kg/m³ 9000 kg/m³ 44 < HD E Material X has an atomic radius R = 0.125 nm, an atomic weight of A = 51 g/mol, and a body centered cubic (BCC) crystal structure. Calculate the mass density of this material. Hint: Do your calculations in SI units, as this will help avoid numerical errors from unit conversions. Choose the answer closest to your calculated value.
1. Match colum A to B Column A Column B ____ Lattice A. Water in a glass tube ____. Adhesive B. Regular repeating patterns in a cell ___. Cohesive C. water, ammonia ___. Crystalline D. Unequal sharing of electrons ___. Amorphous E. Ammonia ___. Liquid F. Compact ___. Viscosity G. Made of repeating unit cells ____. Solid H. No order to the unite cell pattern
1. STP Conditions
The viscosity coefficient of gaseous chlorine at 1 atm pressure and 20 C is 147.0 micropoise. Find the molecular diameter of the chlorine molecule.A. 1.3 E-7cm B. 1.3E-8cm C. 4.3E0-8cm D. 4.3E-7cm
For whole blood flowing in a capillary of radius 1.9x10-4 cm, estimate the maximum velocity for laminar flow at 37°C. (The density of whole blood is about 1.06 g.cm-3. Assume that the viscosity of whole blood is 0.0040 N.s.m-2.) 4.57e3 m.s-1