For the fluid power system shown in Fig, determine the external load F that a hydraulic cylinder can sustain while moving in an extending direction. Take frictional pressure losses into account. The pump produces a pressure increase of 8.5 MPa from the inlet port to the discharge port and a flow rate of 0.0033 m3/s. The following data are applicable. * (Elbow) K =0.75 (Gte valve K-7 9 10 11 K-5 EXI 12 Strainer K=10

For the fluid power system shown in Fig, determine the external load F that a hydraulic cylinder can sustain while moving in an extending direction. Take frictional pressure losses into account. The pump produces a pressure increase of 8.5 MPa from the inlet port to the discharge port and a flow rate of 0.0033 m3/s. The following data are applicable. * (Elbow) K =0.75 (Gte valve K-7 9 10 11 K-5 EXI 12 Strainer K=10

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

asap
A washing machine is supplied with hot and cold water from two different supplies. Draw the bock the diagram of a process control that controls the hot water flow Q? and the cold water flow Q? to adjust the water temperature as the machine user specify? and define each block? Note: pressure controlled pneumatic actuator is used as a valve.
Pump has a displacement of 98400 mm. It delivers 91.2 Lpm of oil at 1000 rpm and efficiency is 81.7 %. If the prime mover has input torque is 12430 N-cm, find the value of pressure. Select one: O a. 6.99x10° N/m O b. 699.2x10° N/m 2 O C. 69.9x10° N/m 2 O d. 6.99x10° N/m
Choose correct answer: The discharge rate requirements are which drive the actuator through a specified displacement and within a given time limit in any type of the pump. Select one: True False
A gear pump has a 80-mm outside diameter, a 55-mm inside diameter, and a 25-mm width. If the actual pump flow rate at 2300 rpm and rated pressure is 140 LPM, calculate the Displacement Volume, VD (m3) Group of answer choices 66.9x 10-7 m3 56.3 x 10-6 m3 66.3 x 10-6 m3 97.1 x 10-7 m3 70.9 x 10-6 m3
A centrifugal pump equipped with a variable frequency (speed) drive running at 3500 rpm is discharging 240GPM corresponding to a head of 287ft. The horsepower is 35.5. if the pump's speed is reduced to 2900 rpm, what will be the revised power required? Select the correct response: 29.32 hp 20.19 hp O 24.37 hp 29.41 hp 34.23 hp 30.37 hp lenovo
Determine the head developed by a multi-stage pump delivering 50 L/s when running at 1450 rpm if the specific speed must not be less than 760. Select the correct response: 88.56 m 61.75 m 81.56 m 71.75 m 78.56 m D 68.56 m
A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
A centrifugal pump equipped with a variable frequency (speed) drive running at 3500 rpm is discharging 240GPM corresponding to a head of 287ft. The horsepower is 35.5. if the pump's speed is reduced to 2900 rpm, what will be the revised flow rate? Select the correct response: 176.21 gpm 76.21 gpm 89.66 gpm 98.85 gpm 289.66 gpm 198.86 gpm
Problem 2: A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: |Q-72 L/s DI = 90 mm D2 = 280 mm Flow rate Inlet diameter OUutlet diameter Нead Width at the inlet Width at the outlet Leakage Mechanical loss Blade angle at the outlet The water density Atmospheric pressure Н- 25m bl -20 mm b2 = 18 mm 9 =2 L/s Pm = 1.41 kW B: = 35 p = 998 kg/m³ 101 kPa 1) Draw the velocity triangles at the inlet and the exit of the impeller. 2) Determine the magnitude of the absolute velocity of the flow (V) and the impeller velocity (U) at the inlet and outlet 3) Determine the blade angle at the inlet. 4) Determine the hydraulic, mechanical and volumetric efficiencies. 5) Determine the minimum number of blades required for the slip to not exceed 0.9. 6) Determine the static pressure difference (P:-P1) through the impeller by using Bernoulli equation. 7) Determine the available NPSH if…
Displacement (c): 0.2 in3/revShank diameter (d) = 0.625 in.Piston diameter (D) = 1.5 in.Rotation speed (n): 1725 RPMPressure (P): 600 PSIStroke (L) = 18in. a) Calculate the theoretical flow rate of the pump in in3/min and US GPM.Theoretical flow (Q) = Theoretical displacement (C) x Speed of revolution (n)Theoretical flow (Q) = 0.2 in3/rev x 1725 rpmTheoretical flow (Q) = 345 in3/min = 1.49 US GPM b) Calculate the cylinder output speed in in/s.Cylinder output speed (VS) = Piston side flow (Q) / Piston area (Ap)Cylinder output speed (VS) = (Displacement x Speed of revolution) / Piston area (Ap)Cylinder output speed (VS) = (0.2 in3/rev x 1725 RPM) / 1.77 in2Cylinder output speed (VS) = (0.2 in3/rev x 1725 RPM) / 1.77 in2Cylinder output speed (VS) = 196.02in/s = 196.02 / 60s = 3.20 in/s Questions: c) Knowing the output velocity (ram speed), calculate the rod side flow in GPM when the ram is extending. d) Calculate the piston exit time in seconds. e) Calculate the piston entry time in…
The impeller of a centrifugal pump having external and internal diameter 500mm and 250mm respectively, width at out let 50mm and running at 200rpm works against a head of 48m. The velocity of flow through the impeller is constant and equal to 3m/s the vanes are set back at an angle of 400 at outlet. Determine A.inlet vane angle B.workdone by the impeller on water per second c.manometric efficiency