For the indicated part. What would be the maximum torque that can be applied to the indicated part if the bar is solid, made of steel, with a diameter of 5 cm, L = 2m and the total angle of torsion in the length cannot exceed 2 degrees? Assume G = 80 GPa. (Hint: Twist angle has to be in radians to use in formula)

Q: A metal bar 10 m long and weighs 50 N is supported at the 7 m mark by a fulcrum. A 100 N bag is…

A:

Q: Calculate x if point B contacted with the square support?

A:

Q: 2m 1.5 m 0.5 m 0.5 m 56m y A a.) A 1.5 m length of 30mm diameter solid steel bar fixed at one end is…

A: Given: The length of solid steel bar, L = 1.5 m The diameter of solid steel bar, d = 30 mm = 0.03 m…

Q: A vertical rod of length L and diameter dis fixed at its upper end and carries a load Wat its lower…

A: Write the torsion equation for the rod. TJ=GθL Here, J is the polar moment of inertia, and G is the…

Q: If an isotropic material has a shear modulus of 21 Gpa and a Poisson's ratio of 0.4, calculate its…

A: The relation between Young's modulus, shear modulus, and Poisson's ratio is given as: E = 2G (1+μ) E…

Q: According to a stiffness based design, a solid shaft has a diameter 50mm and the shear modulus of…

A: here, G= 35 Gpa = 35000 Mpa d = 50mm J = pi×d^4/32 mm4 Torsional rigidity = G×J.

Q: diameter solid steel cylinder in which a 7 mm diameter hole has been drilled from end B up to point…

A:

Q: A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress…

A:

Q: Determine the torque needed to twist a short 2-mm-diameter steel wire through several revolutions if…

A: The yield stress of perfectly plastic material is given as, The torque of perfectly plastic…

Q: The cylindrical rod BC, diameter 3.6 mm made of steel supports the AD bar with a distribution of…

A: Given data dBC=3.6mm E=200 GPa

Q: A 1.2 m pulley is fastened to a 5 in shaft by means of a square key with 140 mm long. What force…

A: Given Data The diameter of the pulley is: D=1.2 m the diameter of the shaft is: d=5 in=127 mm The…

Q: Calculate the total deformation of steelbars shown in Figure. (d1=1A mm, d2=2A mm and E=210 GPa)…

A: Given, A=5B=3C=8d1=1A mm=1×5 mm=5 mm=5×10-3 md2=2A mm=2×5 mm=10 mm=10×10-3 m E=210 GPa=210×109 Pa…

Q: B2 A tube of 50 mm outside diameter and 2 mm thickness is attached at the ends by means of rigid…

A:

Q: A hollow cylinder is used as a torque sensing element with r= 2.5 cm, ro=3.3 cm and L=15 cm.…

A: Given:- T=30 N-mG=8×1010N/m2ri=2.5cm=0.025mr0=3.3cm=0.033mL=15cm=0.15mθ=45° To find:- Size of solid…

Q: 2. A 10-x 10-mm key was used in a 45-mm diameter shaft of a 30 kW diesel engine rotating at 1200…

A:

Q: Determine the torsional stiffness of a solid aluminum shaft of length 2 m and radius of 30 cm. The…

A:

Q: Calculate the percentage elongation of a steel rod, when it is subjected to an axial pulling force…

A:

Q: A hollow circular bar has an inner radius rį and an outer radius r2. If ri = r2/2, most nearly what…

A: Given Data  Inner radius of hollow bar, r1 Outer radius of hollow bar, r2 r1=r2/2

Q: A plastic bar of 53 mm is to be twisted by torques T until the angle of rotation between the ends of…

A:

Q: An aluminium bar is in the form of an equilateral triangle 30 mm on a side. What torque is required…

A: We know that an aluminium bar has 30 mm on each side and is in the shape of an equilateral…

Q: i. A shaft system ABCD consists of a solid bar BD and hollow bar AB is subjected to torque as shown…

A:

Q: Pls answer thank you! A 2 in diameter 6-spline shaft ( d= 0.85D, W= 0.25D, h= 0.075D ) and to slide…

A: Given DataDs=2inn=6d=0.85D=1.7inW=0.25D=0.5inh=0.075D=1.5inL=212inF=2500lbs

Q: Q- A solid 75-mm-diameter Aluminum [E = 80 GPa and 0.3 Poisson ratio] shaft that is 1.25-m long…

A: DAl=Diameter of Solid Aluminum=75 mmLAl=length of Aluminum shaft=1.25 m DB1=Outside Diameter of…

Q: Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the…

A:

Q: To support a tensile load of 65 kN, a circular cross section and A metallic rod with a length of…

A:

Q: A 5-m high aluminum cylinder must support a load of 450 kN. If the maximum allowable stress is 0.14…

A: Write the given values along with the suitable variables.

Q: In the system given in the figure, the rods are identical and it is desired to be produced in the…

A:

Q: A aluminium rod of diameter 45 mm is subjected to a torque of 79 Nm. Assume one end is fixed of the…

A: Given:Diameter of rod,d=45mm=0.045mSo,Radius of rod,r=d2=0.0225 mTorque on rod=79NmLet the hear…

Q: A shaft of 30 kW 710 r.p.m motor is 40 mm in diameter and is supported in bearings 500 mm apart.…

A: Given: The power of shaft is P=30 kW  The revolution of shaft per minute is N=710 rpm  The diameter…

Q: Write the Shear strain max formula for Torsion?

A: To calculate the maximum shear strain value for torsion we must take into account the torsion…

Q: A rod is made from two segments: AB is steel and BC is brass. It is fixed at its ends and subjected…

A:

Q: What will be the minimum diameter of a steel wire, which is used to raise a load of 4000N if the…

A:

Q: a) In your own words, explain in detail the concept of torsion; ensure that the most important…

A: (a) Concept of torsion: If a body is subjected to twisting by applying a couple of shear stress will…

Q: Solid steel post subjecting torsion. Given that the diameter is 75.05 mm, length is 2.5.05 m and…

A: Given   Diameter, d = 75.05 mm Length, L = 2.5 m Shear modulus, G = 78.08 GPa Torque, T = 540 N-m…

Q: A shaft of 30 kW 710 r.p.m motor is 40 mm in diameter and is supported in bearings 500 mm apart.…

A: Given: The power of shaft is P=30 kW  The revolution of shaft per minute is N=710 rpm  The diameter…

Q: 1).Derive the expression for torsion formula of a circular bar?

A: A circular bar or shaft will be called in torsion(more accurately in pure torsion), If there is…

Q: Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear…

A:

Q: 3 An aluminum (shear modulus = 2.8× 1010 Pa) rod is 25 mm in diameter and 50 cm long. One end is…

A: Write the formula for the angle of twist of the aluminum rod. θ=TLGJ Here, θ is the angle of twist,…

Q: A hollow aluminum rod has a max shear stress of 0.075 GPa. What is the maximum torque that can be…

A:

Q: Calculate the required thickness (in mm) of a hollow shaft with outer radius 27.9 mm, required to…

A: Given data: The outer radius is r0=27.9 mm The torsional moment is T=975 Nm Maximum allowable…

Q: A steel shaft 1.4375 inches in diameter transmits 40 hp at 1400 rpm. Assuming a modulus of rigidity…

A:

Q: Question 4 fixed. The shear modulus G and the polar moment of inertia I, of the bar's cross-section…

A:

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given  Su = 345 Mpa  Force = 13 kN  Given figure

Q: 12 mm diameter CE and 18 mm diameter DF bar, ABCD connected to rigid summation. Rods compared to…

A:

Q: A solid 11 mm diameter shaft is subjected to an axial load of P= 33 kN and a torque of T acting as…

A: Sum of moment of intera of two perpendicular axes is known as polar moment of inertia.

Q: 2 Figure 2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: a) In your own words, explain in detail the concept of torsion; ensure that the most important…

A: Given questions are related to solid mechanics.

Q: Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the…

A:

Q: Q-A solid 75-mm-diameter Aluminum [E 80 GPa and 0.3 Poisson ratio] shaft that is 1.25-m long extends…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.