fully loaded elevator cabin has a mass of 1200kg. In 3.0 minutes, the cabin must be raised to a height of 54 meters. Since the counterbalance has a mass of just 950kg, the elevator's engine must assist in balancing the cabin. What is the average power of the motor's tractive force operating on the cabin through a tow rop

fully loaded elevator cabin has a mass of 1200kg. In 3.0 minutes, the cabin must be raised to a height of 54 meters. Since the counterbalance has a mass of just 950kg, the elevator's engine must assist in balancing the cabin. What is the average power of the motor's tractive force operating on the cabin through a tow rop

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

The input piston and output plunger of a hydraulic car lift at the same level, as shown in the drawing. The cross-sectional area of the input piston is 12cm^2, while that of the output plunger is 1200cm^2. The force F1 is applied to the input piston had a magnitude of 150 N. What is the weight W of the car? Neglect the weight of the piston and plunger.
If the maximum length of the spring is 40 cm, what average friction force opposes the motion of the mass?
Two box hang from the ends of a string suspended from a frictionless pulley. The mass on the left is chosen to create a tension of 4 N in the string. The box on the right has a weight of 2 N. What will be the acceleration of the box on the right? Assume the acceleration of gravity is 9.8 m/s?. 4 N 2 N
find the mass of the automobile by treating it as an undamped single-degree-of-freedom system?(Need handwritten solution only please otherwise downvote)
Q2/ The out – of - balance of a machine rotor is equivalent to 5 kg at 10 mm radius in one plane A, together with an equal mass at 15 mm radius in a second plane B. AB = 375 mm and the two radii are 120°. Find the mass required in third plane C at a radius of 125 mm and its angular position with respect to the given radii so that there is no resultant out - of - balance force. Find also the position of C along the axis for the residual couple to be a minimum and of this couple when the speed is 500 г.p.m.
Q2/ The out - of - balance of a machine rotor is equivalent to 5 kg at 10 mm radius in one plane A, together with an equal mass at 15 mm radius in a second plane B. AB = 375 mm and the two radii are 120°. Find the mass required in third plane C at a radius of 125 mm and its angular position with respect to the given radii so that there is no resultant out - of - balance force. Find also the position of C along the axis for the residual couple to be a minimum and of this couple when the speed is 500 r.p.m.
A 30kg mass is tied to a uniform rod whose mass and length are 80-kg and 8-m, as shown below. The rod is attached to the floor via a hinge and makes an angle of 70° relative to the ground; a massless string is also attached to the rod at the ¼ point of the rod and makes an angle of 20° relative to the horizontal. What tension must be provided by the rope so that the system remains in stationary? If at some point the string breaks, what will be the angular acceleration of the system the instant that the string breaks?
Consider a uniform ladder of length 4.3 m and mass 10 kg. The ladder is falling over, pivoting about the end that is touching the ground. Someone is pushing on the top end of the ladder with a horizontal force of size 415 N. At the instant when the ladder makes a 46 degree angle with the horizontal, calculate the net torque on the ladder about its bottom end, in N m. Make your answer positive, and use g = 10 m/s2. (Please answer to the fourth decimal place - i.e 14.3225)
The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of the fulcrum. The hook which carries the load,weights 4kg and is also attached on the left-hand side of the fulcrum at a distance of 12cm.if graduation mark 72cm from the fulcrum reads 50kg. Find (a).the weight of rider (b). How far is the zero graduation from fulcrum (c).What is the movement of riderper kg of graduation?
A 6-m long ladder has a mass of 16 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal.How far up along the ladder can a 79-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B.
A uniform ladder 8 meters long and weighing 350 N rest against a smooth vertical wall at an angle of 30° to the wall. A 700-N man stands 6 meters up from the bottom of the ladder. Find the horizontal force necessary at the base to keep the ladder from slipping. please use the end at the top as the reference point.
A 6-m long ladder has a mass of 10 kg, and its center of gravity is 2.4 m from the bottom along the ladder. The ladder is resting on a 5° upward sloping floor at A and on a wall inclined to the right at 5° from the vertical at B, so that it makes an angle of 60° with the horizontal. How far up along the ladder can a 78-kg man climb before the ladder is on the verge of slipping? The angle of friction at all contact surfaces is 15°. Also determine the total reaction at A and B in Newton. Note: Point A is at the left of point B. SOLVE ASAP