Given are the interior angles of a heptagon. Determine the discrepancy for the given observation and the most probable value of each angle. ABCDEFG 128°34′17" 112°49'02* 83°12'38" 132°11'44" 128°26'19" 194°45'09 120°0'44"

Given are the interior angles of a heptagon. Determine the discrepancy for the given observation and the most probable value of each angle. ABCDEFG 128°34′17" 112°49'02* 83°12'38" 132°11'44" 128°26'19" 194°45'09 120°0'44"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Calculate the ultimate moment capacity of the section in PART B in kN.m.0

A: Given- A simply supported beam carrying different loading system. Required- To calculate ultimate…

Q: Investigate the flexural adequacy of the beam sections of figures 1 and 2 to carry the given loads…

A: Given- A simply supported beam carrying different loading system Required-To check the flexural…

Q: Q4: A simply supported I-beam of (2 m) span carries a central load of (4 kN). The load acts through…

A: Calculation of Maximum Bending stress at mid Span and Location of NA ##

Q: 20ft P= 20K Mmax= A max =

Q: 22/ Complete the settlement table below and verify the correctness of the calculations. Then check…

A: We knowHIn=Elvn-BS1Elvn+1=HIn+FSn+1

Q: Define Cast-in-drilled-hole (CIDH) pile

A: Cast-in-drilled-hole (CIDH) pile are simply reinforced concrete piles cast in holes drilled to…

Q: Saturated clay has the void ratio of 1.65 and density of solids (or density of solid particles) of…

A: Answer We know that horizontal total stress for at rest earth pressure is given by σH = Ko*σV σH =…

Q: A soil sample has a moist unit weight of 18.02 KN/m^3 and a water content of 22.50 %. Determine the…

Q: The cantilever beam shown in the figure consists of a rectangular structural steel tube shape [E =…

A: Given:E=200 GPaI=95×106 mm4PB=20 KNPC=53 KNwAB=61 KN/mwBC=19 KN/mL1=1.6 mL2=3.3 mNow,Using the…

Q: 3. The body on the 30° incline is acted upon by a force P inclined at 20° with the horizontal as…

Q: Consider the following data for designing a taxiway for operating Boeing 707-320 aeroplane: Wheel…

A: Given data: Wheel base, w = 17.70 m Tread of main landing gear = 6.62 m Turning speed, v = 40 km/h…

Q: The following subtended angles were read on a 2m long subtense bar using a theodolite. Compute for…

Q: What is the main difference between satellite images and aerial photographs?

A: Difference between satellite images and aerial photographs are mentioned in fallowing table

Q: V=445 suced by 2070: Q5/ A circular curve of 145.00 m radius is to be set out between two straights…

Q: Determine the force in each member of the truss. Indicate if the members are in tension or…

Q: Calculate the horizontal distance between the staff and instrument, if the staff readings are 1.4 m…

A: Given- Staff readings=1.4 m & 2.9 m,Anallactic lens. It is needed to find the horizontal…

Q: A hollow steel column has to carry an axial load of 2,00,000 kg and the ultimate stress for the…

Q: 4. In a closed watershed where ground water does not cross the watershed bounda have the following…

A: given data, BF, Baseflow = 10 in/yr OF, overland flow = 2 in/yr P, rainfall = 50 in/yr ET,…

Q: The gradient for a B.G. railway line such that grade resistance together with the curve resistance…

A: given- B.G. railway line, 4 degree curve, gradient 1 in 250.

Q: For Problem 19.22 , determine the probability (assuming normal distribution) that a light bulb would…

A: Given:-series of experiments=135To find:-plot the data and calculate the mean and standard deviation

Q: Disregarding material cost, how much is the total salary expenses for Design 1 and for Design 2.…

A: Given Data:Design 15 men costing P500/day Duration = 4monthsDesign 210 men costing P350/dayDuration…

Q: Mma A max: lax=

A: Given: Length of cantilever beam, L = 20 ft Uniformly distributed load on full span, w = 1 klf The…

Q: show complete solution) 2. A stadia rod held at a distant point B is sighted by an instrument set…

A: Given Lower value =0.5 Upper value =1.6

Q: The built-up steel beam section is shown in the figure. Determine the center of gravity (mm)…

A: Given data:

Q: Assuming the plates are 15 feet tall and 6 feet long, and are arranged with three mechanical…

A: Given Data The plates are 15 ft tall and 6 ft long H = 15 ft L = 6 ft Number of mechanical fields…

Q: solve and show complete solution The following subtended angles were read on a 2m long subtense bar…

Q: Find the value of the pull required to eliminate the effect of sag when the 50 m long tape weighing…

A: Given: L=50 m =50000 mmA=0.05 cm2=5 mm2Po=10 kg=10×9.81=98.1 NE=200 GPa=200×1000=2×105 Nmm2w=0.03…

Q: Q for the shown in Fig (5), find the force in members "a and b" using approximate analysis. 20N A…

Q: For the beam shown in Fig. (5) construct the influence line for the shear force at C and moment at…

Q: Q- A simply supported rectangular concrete beam of span 8 m has to be prestressed with a force of…

Q: A saw-tooth loading is applied as shown in the figure. The flexural stiffness (EI) of the beam is…

A: Given a propped cantilever beam carrying UVL loading. Required- To calculate support reactions.

Q: A river barge, whose cross section is approximately rectangular, carries a load of grain. The barge…

Q: supports

Q: Current Attempt in Progress A 2-ft-thick block constructed of wood (SG = 0.6) is submerged in oil…

Q: A component made of Aluminium 6061-T651 has an edge crack with length equal to 15 mm, as shown The…

Q: SOLVE FOR THE ANGLES: N.20 25 50"W S.20° 25' 50"W. S.52 21' 30"W. S.85 30' 16"E. + S.69 59' 10"W.…

Q: Situation 1: The crate has a mass of 50 kg. ps = 0.25 μk = 0.20 30° 1. Determine the minimum…

A: To find out the, a) Minimum horizontal force P required to hold the crate from sliding down. b)…

Q: 3. The average rainfall rate in a watershed with an area of 50 mi² in the upstate of South Carolina…

A: Given: Area=50 mi2Avg rainfall rate=62 in/yrAvg stream discharge=26 in/yr We need to calculate…

Q: Using Double Integration Method derive an expression for the following: a) Reaction at propped…

Q: Part A Determine the magnitude of the resultant hydrostatic force the water exerts on the face AB in…

A: Given : To Find : FR & thetha ?

Q: 1. The taped distance of a line is 99.182 m using a 100 m steel tape weighing 2 kg at standard pull…

Q: Concrete overhang beam is to support the concrete slab w/ tributary width 2.70 m. The beam also…

A: Given Data- a concrete overhang beam of span 6m concrete slab of 150mm thick with tributary width…

Q: A timber beam AB of span 5 m, width 100 mm and height 200 mm is to support three concentrated loads…

Q: 1. WHAT IS THE AREA OF A REGULAR HEPTAGONAL FIELD (IN m^2) IF ONE SIDE OF THE HEPTAGON IS 1500 FEET.…

Q: At a certain station, the mean of the average temperature is 25°C and mean of the maximum daily…

A: GIVEN :- Average mean temperature = 25° C Maximum mean daily Temperature = 46 °C To Determine :-…

Q: Current Attempt in Progress A 2-ft-thick block constructed of wood (SG = 0.6) is submerged in oil…

Q: Line Distance AB BC CD DE EF FG 62.56 29.49 65.07 41.14 43.70 26.74 Forward Bearing N 81-02-05 W N…

A: Given: LINE FB BB AB N 81-02-05 W S 79-26-30 E BC N 08-16-07 W S 13-18-15 E CD S 87-34-45 E…

Q: Determine the adjusted forward bearings of the following survey data LINE CD DISTANCE 65.07 FORWARD…

Q: Explain Predrilling, Jetting, and Spudding

A: Pre-drilling is the process of creating a hole in a piece of work that is smaller in diameter than…

Q: unstretched. Neglect the weight of the bar. 30 N 1 m wwww B 2 m Probs. 5-39/40 ne www springs are

Question

II.
Theory of Errors
1. Given are the interior angles of a heptagon. Determine the discrepancy for the given
observation and the most probable value of each angle.
ABCDEFG
128°34*17"
112°49'02"
83°12'38"
132°11'44"
128°26'19"
194°45'09"
120°0'44"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Note: Use sketch wherever necessary! (Q1) Compute the coordinate of point P in the below figure, if you know the azimuth of AB equal (αAB= 240°10′05") and horizontal distance pf line CP equal (Scp=250.34 m). P(?, ?) C(?, 1227.52) 82 01 B(1030.10, ?) A (1372.71, 1215.30) 01- 113°56'39" 02 92°20'18"
Q4: From the figure below find the azimuth for each leg, then esimate the allowable angular error. 270° 67 310° 16 120° 0 6 19 AZIMUTH MARK STATION A NORTHING 740.79 EASTING - 5497.53 313 28
Compute the angle (0) from the below figure: A(11150.509, 11825.802) B(11807.821, 11582.456) 402 F(10844.768, 11314.065- 43 E(11573.364, 10708.791) D 0 C 41= 144°47' 29" 2=116° 47' 52" 43=126° 04′ 33"
Find the distance of AB = S (m) and azimuth (AB) in grad between two points whose coordinates are given below. Pick the correct answer from below. PN Y(m) X(m) A 42356.25 67452.79 B 64526.63 74523.65 Oa.23270.64m and 799.1081 Ob. 23270.64 m and 80% 3454 Oc34228.64 m and 919 2984 Od. 24228..64 m and 819,9984 Oe. 24228.64 m and 819.3454
Pleasedraw the figure in this problem The following data were obtained by stadia observation: vertical angle Ѳ = +9degree25min, upper stadia hair and lower stadia hair readings are 2.352 m and 0.995 m, respectively. The stadia interval factor is known to be 99.0 and C = 0.381 m. The height of the instrument above the instrument station (point A) is 1.496 m and the rod reading is taken at 1.589 m. Elevation of point A is 776.545. determine the inclined distance AB? In Problem 1, Determine the elevation of B In Problem 1 determine the vertical distance In Problem 1 determine the horizontal distance
Which one is the CORRECT expression for the horizontal distance between the instrument and the staff for the anallactic telescope, if S is the staff intercept, K and C are multiplying and additive constant? 100C S 100S
Theory of Errors1. Given are the interior angles of a heptagon. Determine the discrepancy for the given observation and the most probable value of each angle. A 128°34’17”B 112°49’02”C 83°12’38”D 132°11’44”E 128°26’19”F 194°45’09”G 120°0’44”
Complete the table below. C 118°37 9 105°22' Sta A B C D E 108° 28' E B 120°28' N30°00'W MERIDIAN 87°05' DEFLECTION ANGLE ANGLE TO THE RIGHT
Distance by Tachymetry (show complete solution) 2. A stadia rod held at a distant point B is sighted by an instrument set up at A. Determine the length of line AB if the upper and lower stadia readings were observed as 1.60 and 0.50 respectively
Thank you
The angles about a point R have the following observed values. A = 120°5’ 20”, B = 132°27’30”, and C = 107°27’40”. Determine the adjusted measured angle A by assuming that the error is the same for each angle. a.130°15’ 30” b. 120°5’ 30” c. 130°15’ 10” d. 120°5’ 10” e. not listed
Compute the angle 0 in the below figure (in grad), if you know the directions in grads aAB=128.5772° and ABc=245.91268 (Example answer 35.2345) A B