Given:Find:••VLoad = 120VLoad 1: Balanced Delta connected load with the phase impedance ZLoad = 8+ j4nLoad 2: Balanced Wye connected load with the phase impedance Zload2 = 2-j1nLoads are connected in parallel.Line impedance is RLine = 0.20Sketch the circuit.The total real power delivered to Load 1.The total real power delivered to Load 2.The power lost in the line.

In this question, the given details are,,Load 1: Balanced Delta connected load with the phase…

Given: • VLoad 120V = Load 1: Balanced Delta connected load with the phase impedance ZLoad = 8 + j4n Load 2: Balanced Wye connected load with the phase impedance ZLoad2 = 2 - jin Loads are connected in parallel. Line impedance is RLine = 0.20 Find: • • Sketch the circuit. The total real power delivered to Load 1. The total real power delivered to Load 2. The power lost in the line.

Given: • VLoad 120V = Load 1: Balanced Delta connected load with the phase impedance ZLoad = 8 + j4n Load 2: Balanced Wye connected load with the phase impedance ZLoad2 = 2 - jin Loads are connected in parallel. Line impedance is RLine = 0.20 Find: • • Sketch the circuit. The total real power delivered to Load 1. The total real power delivered to Load 2. The power lost in the line.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What are the real, reactive, and apparent powers seen at load 1? Give also the power factor.
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
In a balanced Y-Y circuit shown in Figure 5, the magnitude of the phase voltage at the source is Vp = 2520 V (rms) and Van = 252020° V (rms). The load impedance is Zy = 135 + j55 Q per phase and the wire impedance is Zw=85 + j65 per phase. All the voltages and currents are in rms in this problem. (a) Find the phasors for line currents IA, IB, Ic in rms. (b) Find the load voltage VAN = IAZY. Also find VBN, and VCN. (c) Find the line voltages VAB, VBC, VCA at the load. (d) Find the complex power SL of the load. ZW ZY Van a A IA ZW ZY Vbn b В IB N ZW ZY Vcn IC Figure 5
Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a 55ohm resistance and a 0.05H inductance per phase 3. second load consumes 1kW and power factor of 0.7 lagging per phase 4. RMS of voltage across the loads are 220V, frequency 120Hz per phase 5. single phase equivalent is shown in the figure: Question: What is the total power drawn from the 3 phase source?
A balanced delta connected load contains 8 + j4 ohms per phase, while a balanced wye connected loadconsists of 2 – j1 ohms per phase. Both loads are connected in parallel to a three-phase three-wire system inwhich the line voltage is 120 V rms at the loads. The three lines extending from the loads to the source eachhave a resistance of 0.2 ohms. Determine the power lost in the wires.a. 1.42 kW b. 1.38 kW c. 1.24 kW d. 1.83 kW ( please stay on choices, thanks) ..
3 The load Z, in the circuit of Figure P7.28 consists of a 25-2 resistor in series with a 0.1-mF capacitor. Assuming f = 60 Hz, find %3D
Draw a 3-phase wye-connected generator with transmission lines connected to a 3-phase delta-connected load. Assume the lines connecting them have an inductance of j5 per phase. The generated voltages are 120 Vrms with phase 'a' having a phase angle of 0°. The loads are 10 Ohm resistors per phase. When drawing, make sure to label all 3 phases with voltage phasors, line inductances, and load resistances.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Suppose that a current source with Is amperes of current is connected in parallel to a pair of impedances Z₁ and Z2. Let I₁ be the current through Z₁ and 12 be the current through Z₂. Then, the total voltage Is is divided between 1₁ and 12 in proportion to impedance values Z₁ and Z2. a. True O b. False
7. Consider an equivalent single phase circuit as shown in the figure V=22020⁰ i) a I ii) iii) 22092 J22002 Find the currents I II and I Find the total real power supplied by the source Find the total reactive power supplied by the source XIS -J22092